RM05 Touch Screen Streaming Video Rear View Mirror

Important Notice

• NOTICE: Due to high power consumption, this unit must always be connected to an external power supply. It will not power on without one.
• This product is intended for use in motor vehicles only. Do NOT install the device where it might block the driver's view of the road (including mirrors) or the deployment of the airbag.
• Before using this device, insert the memory card first and format it to FAT32 on a PC. Then, format the memory card in the camera menu.
• This device records video at high resolution. Use a high-speed memory card (Class 10 or above recommended, 16GB or 128GB cards are recommended).
• Perform a benchmark test to ensure the unit is working perfectly before installing it in your vehicle.
• Ensure the lens is clean and unobstructed.
• Use only the original included power adapter.
• DO NOT leave the device in direct sunlight for extended periods or where temperatures may exceed 170°F (75°C).
• The GPS function requires the customized GPS module. Download "GXplayer" (contact the seller for details).

Installation Guide

1. Before installation, insert a high-speed memory card and format it in the unit's settings. Perform a simple test to ensure the unit is working perfectly.
2. Mount the mirror over the original rearview mirror using the included rubber rings. Ensure it is securely in place.
3. Adjust the mirror angle according to your driving position for a clear view.
4. Adjust the lens angle for optimal coverage of the hood and road ahead.
5. Connect the power adapter to the mirror and the cigarette lighter. Route the power cable along the interior trim board, hiding excess cable in gaps for a clean look.
6. The rearview camera should be installed at the rear of the car, typically above the license plate. It can be fixed with the sticker or screw.
7. (Note: Check if the backup camera is installed correctly before securing with screws.)
8. The RED lead near the rear view camera is for reverse status sensing. Connect the RED cable to the positive lead of the reverse lamp power.
9. Route the backup camera cable to the front of the car and connect it to the main unit.
10. (NOTICE: Holes may need to be drilled. Check if the backup camera cable is long enough for your car before installation.)
11. After installation, start the engine and test all functions.
12. NOTICE: Wiring and installation require manual dexterity and professional skills. Seek professional help if unsure.

Wiring Method A & B are illustrated to show cable routing.

Adjust the Reversing Camera

Adjust the reversing camera angle so it covers the rear of the car and the ground surface beneath the rear end.

Notice: When the car is in reverse, the rear camera will automatically display in full screen and adjust to the lowest angle, allowing you to see the ground surface under the rear end.

Interface and Button Functions

The unit automatically powers on and starts recording when the car engine starts.

Interface Icons:

• Mute Icon: Click to turn ON/OFF audio recording in video.
• Photo Icon: Click to take a photo.
• Record Video Icon: Click to start/stop video recording.
• Setup Icon: Click to enter the Setup menu.
• Playback Icon: Click to enter the camera playback interface.
• Lock Icon: Click to manually lock the current video.

Shortcut Operation

In the recording interface:

• Slide horizontally to the right to enter Playback Mode.
• Slide horizontally to the left to switch between Front and Rear camera display modes.
• On the right side of the screen, slide vertically up and down to adjust screen brightness.
• On the left side of the screen, slide vertically up and down to adjust the lens view angle.

Playback Mode

In Playback Mode, you can:

• Exit
• Folder Selection
• Multiple Selection
• Delete
• Playback

Setup Menu

Featured Function

Dual Recording

The RM05 mirror has dual channel lenses, recording video in Front 4K (3840*2160) and Rear 1080P (1920*1080) simultaneously.

Loop Record

Set video file length to 1/3/5 minutes. When storage is full, the camera loops back to the earliest file and overwrites it. For example, with a 3-minute setting, clips are recorded in 3-minute intervals. When the card is full, it continues recording and overwrites the earliest unprotected 3-minute file.

G-Sensor

The built-in Gravity sensor triggers and locks the current video file in case of a serious vehicle collision or rapid acceleration/deceleration, preventing it from being overwritten by loop recording.

Parking Guard

The Parking Monitor protects your car after parking. When the car is stopped and the unit is off, it enters standby. Upon detecting a significant shock, it automatically turns on, records a 20-second video, and then shuts down. Videos recorded under parking monitor are protected and not overwritten by loop recording.

Screen Saver

Set the time after which the unit automatically turns off the screen to save power and reduce driving distractions. If the unit is not operated for a set time (e.g., 3 minutes), the screen turns off while recording continues. Any button operation or screen touch reactivates the display.

Streaming Media

The "Back Mirror" function displays the rear camera view in full screen by default, acting as a real rearview mirror.

GPS Function

With the GPS module connected, the RM05 can display the current speed. Check the GPS signal status in the setup menu. Speed units (KM/H and MPH) are optional.

NOTICE: The displayed speed is an average calculated from locations and time, and may have errors, especially at low speeds. It is for reference only.

GPS Logger

With the GPS module connected, the RM05 records real-time GPS coordinates in the video file, viewable with the customized GPS player.

NOTICE: The GPS playback requires the customized player "GXPlayer" (contact seller support). Available for Windows operating systems only.

Specification

Common Problem and Solution

Recorder shows memory full, unable to loop video, etc.

1. When using a new memory card for the first time, format it to FAT32 on PC, then format it in the camera. If the card was previously used on another device, it needs to be formatted on this camera. Consider using a new SANDISK 32G Micro SD CARD.
2. Check the G-sensor sensitivity. High sensitivity can trigger the G-sensor due to bumping and shaking, locking files that cannot be overwritten. Accumulated locked files prevent loop recording. Shaking also causes stray files when parking guard is on, affecting card reading/writing.

The device will automatically turn on or turn off.

1. Format the memory card to FAT32 on PC, then format it in the camera.
2. Check if the parking guard function is enabled. With parking monitor on, the device turns on and records upon detecting a collision or shaking.
3. Check the car charger connection. An unstable power supply due to a loose connection can cause the camera to turn on and off automatically.

The rear camera does not display image

1. Switch the camera display mode to check the rear camera status.
2. Ensure the AV plug and cable are properly connected.
3. Disconnect the camera, clean the connector with medical alcohol, and reconnect.

Screen operation or button reaction is slow during recording

1. Ensure the memory card is high-speed (Class 10). Using a non-high-speed card can lead to missed seconds, video playback jams, screen display issues, and crashes.
2. Reset the camera if necessary.

Change in the setting menus won't save.

1. After changing settings, manually press the Power button to shut down; this saves the device settings.
2. Abnormal power-off may prevent settings from being saved.
3. Low battery levels might cause customized settings to be lost.

Even though set the screen saver, but the screen will randomly come back on.

The power supply might be unstable. Try using a different car charger.