BULLSEYE TRX

Introduction

Congratulations on selecting the White's Bullseye TRX pinpointer. The Bullseye TRX is unlike any other pinpointer on the market. Using the latest miniaturized components, White's has integrated a complete ground-balancing Very Low Frequency (VLF) circuit inside the TRX housing. The Bullseye TRX offers excellent sensitivity and "grabs" the ground to detect deeper targets.

The Bullseye TRX packs in more features than any other pinpointer. Features include ratcheting ground grab, proportional response, selectable beeper and/or vibrator, LED light, lanyard loops, dual battery operation, and a weatherproof housing with depth markings, making the Bullseye TRX a comprehensive pinpointer.

Batteries

The Bullseye TRX can accept either two AA batteries (included) or a single 9V battery.

Two AA Batteries: Illustration shows two AA batteries and a battery adapter. The adapter has contacts for the AA batteries and a connector that fits into the pinpointer.

One 9V Battery: Illustration shows a 9V battery and a battery adapter. The adapter has contacts for the 9V battery and a connector that fits into the pinpointer.

Battery installation is easy and is illustrated in the diagrams.

To see complete details or to purchase the White's Bullseye TRX Pinpointer, visit: http://www.metaldetector.com/whites-bullseye-trx-pinpointer

Features

Audio alert

Produces a repeating beep on target detection. The repetition rate of the beeps increases as the probe gets closer to the target. Most targets within 1/4" of the probe result in a continuous tone. The audio alert can be turned off.

Vibrate alert

A vibrator produces short, repeating vibrations in sync with the audio alert. The vibrator can be turned off or used alone, without the audio alert.

LED light

An LED provides illumination while probing and acts as a power-on indicator.

Ground balance

A quick-press of the button "grabs" the ground reading for accurate ground balance.

Target ratcheting

A quick-press of the button ratchets in on strong target signals.

Overload indicator

An excessively large target will create a series of long responses.

Low battery alert

During power-on, three cycles of a two-tone alarm indicate a low battery. During operation, each button press will create the same alarm if the battery is low. The LED also blinks continuously to indicate a low battery.

Holster

Bullseye TRX includes a carry holster, which fits up to a 3-inch wide belt. It also includes a lanyard attachment loop.

Ruler

The Bullseye TRX has a ruler imprinted into the housing for determining target depth.

Dual battery operation

The Bullseye TRX operates with either two AA batteries or a single 9V battery using the included adapter.

Lost pinpointer alarm

If you leave your Bullseye TRX powered on, after five minutes of inactivity it sounds a long beep every 15 seconds to help you relocate it. A quick-press of the button resets the five-minute timer. The bright orange battery cap also helps in finding a lost Bullseye TRX.

Automatic power-off

After five minutes, the lost pinpointer alarm ceases and the Bullseye TRX powers down with a two-tone beep.

Replaceable shell

Scraping around in the dirt will eventually wear through the plastic of any pinpointer. The Bullseye TRX is built to last with an easily replaceable shell that saves you money.

Operation

Power On

1. Hold the unit away from the ground and any metal.
2. Quickly press and release the button. The Bullseye TRX will beep once followed by two short beeps indicating that it's ready to use. ▶️

Power Off

1. Press and hold the button for half a second.
2. When you hear a two-tone beep, release the button. The unit will power down. ⏹️

Ground/Target Reset

During operation, a quick press of the button performs a "grab" function. In the absence of a target, this grabs the ground phase and resets the ground balance. In the presence of a target, it can be used to ratchet in on strong target signals.

Beep or Vibration Selection

The Bullseye TRX can indicate target proximity with either an audible beep or a vibration response. Both are "on" by default, but it is recommended that you choose one or the other to minimize battery drain.

To change selection:

1. Turn the unit on.
2. Press and hold the button for half a second, and listen for the two-tone power-down jingle.
3. Continue holding down the button. After two more seconds, the Bullseye TRX will enter Setup Mode, signified by a two-tone "boo-beep".
4. Continue holding down the button. After another two seconds, the Bullseye TRX will begin to cycle through the beeper/vibration selections:
   • Beeper and vibrator
   • Beeper only
   • Vibrator only
   Note: the selection always starts with the currently selected mode.
5. When you reach the desired selection, simply release the button and the Bullseye TRX will exit setup, indicated by two short beeps. ✔️

Changes to this setting are automatically saved when the TRX is powered off.

Locating and Digging

When you locate a target with your primary detector, before digging a hole, use the Bullseye TRX to scan the surface of the ground. Do this by pointing the unit straight down and moving it around the suspected area. Often the target will be less than 3" deep and can be detected with the Bullseye TRX, making recovery easier.

If a surface scan doesn't detect the target, dig an appropriate plug or flap cut in the turf. Use the Bullseye TRX to scan both the plug (or flap) and down into the hole. In some cases, a coin on edge will be difficult to pinpoint and may be in the sidewall of the hole. Be sure to scan the walls of the hole.

Scanning the surface: The Bullseye TRX's area of detection is concentrated around the tip, making it easy to zero in on the target.

Be mindful of proper digging techniques when extracting the target. Use the smallest appropriate digging tool, especially in public areas. Learn to cut plugs that avoid turf damage or, better yet, how to "pop" coins using only a screwdriver. There are numerous videos on YouTube that demonstrate good target extraction protocol. ▶️

Scanning a dirt pile or hole: When scanning a dirt pile, hold the Bullseye TRX at an angle between 90° (perpendicular) and 45°.

Coins in sidewall: Coins that are on edge are often in the wall of the hole. As the tip is lowered into the hole, the peak response is produced as the tip passes the coin.

To see complete details or to purchase the White's Bullseye TRX Pinpointer, visit: http://www.metaldetector.com/whites-bullseye-trx-pinpointer

Troubleshooting

Specifications

To see complete details or to purchase the White's Bullseye TRX Pinpointer, visit: http://www.metaldetector.com/whites-bullseye-trx-pinpointer

Warranty

If within two years (24 months) from the original date of purchase, your White's detector fails due to defects in either material or workmanship, White's will repair or replace, at its option, all necessary parts without charge for parts or labor.

Simply return the complete detector to the dealer where you purchased it or to your nearest Authorized Service Center. The unit must be accompanied by a detailed explanation of the symptoms of the failure and proof of date-of-purchase.

This is a transferable manufacturer warranty, which covers the instrument two years from the original purchase date, regardless of the owner.

Items excluded from the warranty: non-rechargeable batteries, accessories that are not standard equipment, shipping/handling costs outside the continental United States, Special Delivery costs (Air Freight, Next Day, 2nd Day, Packaging Services, etc.) and all shipping/handling costs inside the continental United States 90 days after purchase.

White's registers your purchase only if the Sales Registration Card is filled out and returned to the factory address by your dealer, soon after original purchase.

The warranty does not cover damage caused by accident, misuse, neglect, alterations, modifications, unauthorized service, or prolonged exposure to corrosive compounds, including salt. Duration of any implied warranty (e.g., merchantability and fitness for a particular purpose) shall not be longer than the stated warranty.

Neither the manufacturer nor the retailer shall be liable for any incidental or consequential damages.

Some states, however, do not allow the limitation on the length of implied warranties, or the exclusion of incidental or consequential damages. Therefore, the above limitations may not apply to you. In addition, the stated warranty gives you specific legal rights, and you may have other rights which vary from state to state.

The foregoing is the only warranty provided by White's as the manufacturer of your metal detector. Any extended warranty period beyond two years, which may be provided by a dealer or other third party on your detector, may be without White's authority, involvement and consent, and might not be honored by White's Electronics, Inc.

To see complete details or to purchase the White's Bullseye TRX Pinpointer, visit: http://www.metaldetector.com/whites-bullseye-trx-pinpointer

Quick Start

1. Quick-press the button to turn on. ▶️
2. Quick-press the button to "grab" a ground reading or to ratchet in on a strong target. ?
3. Press and hold the button for half a second to turn off. ⏹️

Customer Support

Questions concerning your Bullseye TRX? You can contact White's Electronics via internet, phone, or mail:

Internet: http://whiteselectronics.com/support.html

US Contact:
1-800-547-6911
White's Electronics
1011 Pleasant Valley Road
Sweet Home, Oregon 97386

UK Contact:
(0044) 1463 223456
White's Electronics
35 Harbour Road
Inverness, Scotland IV1 1UA

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by White's Electronics could void the user's authority to operate the equipment. ✔️