VEVOR Tile Cutter

Product Overview

This document provides instructions and safety information for the VEVOR Tile Cutter, Model: 8106C-8L/48".

VEVOR is committed to providing tools at competitive prices. While phrases like "Save Half" or "Half Price" represent an estimate of potential savings compared to major brands, customers are encouraged to verify savings for specific categories.

Specifications

Safety Information

General Warnings:

• ⚠️ Warning: To reduce the risk of injury, user must read instructions manual carefully.
• ⚠️ Warning: This symbol indicates a kind of precaution, warning, or danger. Ignoring it may lead to an accident. Follow recommendations to reduce risk of injury, fire, or electrocution.
• ? Warning: Be sure to wear eye protectors when using this product.
• ? Warning: Be sure to wear gloves when using this product.

General Safety Precautions: Read and understand all instructions before using this tile cutter. Follow basic precautions to reduce the risk of personal injury and/or damage to the equipment. Familiarize yourself with hazard notices. Failure to follow instructions may result in property damage, injury, or death.

Work Area Safety

1. Operate in a safe, clean, well-lit work environment, free of distractions.
2. Keep anyone not wearing appropriate safety equipment away from the work area.
3. Store new tools properly in a safe and dry location to prevent rust or damage. Keep the tile cutter away from children.
4. Always place the tile cutting machine on a level and firm surface.

Personal Safety

WARNING! Wear personal protective equipment approved by the Canadian Standards Association (CSA) or American National Standards Institute (ANSI).

Personal Protective Equipment (PPE)

1. Always wear impact safety goggles that provide front and side protection for the eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI Z87.1 standards.
2. Wear gloves that provide protection based on the work materials or to reduce the effects of tool vibration.
3. Caution! The edges of cut tiles are sharp.

Personal Precautions

Control the tile cutter, personal movement, and the work environment to avoid personal injury or damage to the tile cutter.

1. Do not operate the tile cutter when tired or under the influence of drugs, alcohol, or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the tool's moving parts. Keep long hair covered or bound.

Specific Safety Precautions

1. The tile cutting machine is fitted with a replaceable circular blade. Keep the tile cutter and blade away from children.
2. Use the correct tile cutter for the job. This tile cutter is designed for a specific function; do not modify or alter it for unintended purposes.
3. After use, store the machine in a safe and dry place.
4. This machine is designed for cutting and breaking ceramic, glazed, porcelain, and polished tile with a flat surface. It shall not be used for any other purpose.

WARNING! Do not let comfort or familiarity with the product replace strict adherence to the tile cutter safety rules. Unsafe or incorrect use can lead to serious personal injury.

WARNING! Direct exposure of pressurized air or fluids to skin could result in severe bodily injury.

Parts Included

• 1. Cutter *1PCS
• 2. AAA Battery*2PCS
• 3. Ruler *1PCS
• 4. Spare Cutting Wheel Φ22*Φ6*6mm *1PCS

Note: Diagrams illustrating parts and assembly are not included in this text-based conversion.

Operation Instructions

Straight Cutting

Step 1: Place the cutting wheel on the rear edge of the tile. Slide the wheel forward by pushing the handle down with medium pressure, scoring the tile surface glaze. Make one continuous motion, scoring the surface only once per time.

Step 2: After scoring and without moving the tile position, ensure the breaker is slightly in the front edge of the tile and front stop. Raise the handle slightly so the breaker is flat on the tile. Apply increasing pressure on the handle until the tile snaps along the score line.

Tips: After scoring, it is better to pull back the handle to let the breaker slightly backtrack 5-10mm; this is the best position to break the tile. Do not press in the middle or the end.

Diagonal Cutting

Step 1: Put the tile on the machine against the adjusted angle ruler. Place the cutting wheel on the rear edge of the tile. Slide the wheel forward by pushing the handle down with medium pressure, scoring the tile surface glaze. Make one continuous motion, scoring the surface only once per time.

Step 2: After scoring and without moving the tile position, ensure the breaker is slightly in the front edge of the tile and front stop. Raise the handle slightly so the breaker is flat on the tile. Apply increasing pressure on the handle until the tile snaps along the score line.

Tips: Do not place the tile too far inside to ensure the scoring line is a whole line. After scoring, it is better to pull back the handle to let the breaker slightly backtrack 5-10mm; this is the best position to break the tile.

Laser Device Instruction

The laser device has four adjustment screws:

1. Screw 1 & 2: For left/right bias adjustment. If the laser is biased to the left, adjust screw No. 2 clockwise or screw No. 1 counterclockwise. If the laser is biased to the right, adjust screw No. 1 clockwise or screw No. 2 counterclockwise.
2. Screw 3 & 4: For irradiation distance/height adjustment. When the laser irradiation is too far/high, adjust screws No. 3 and 4 clockwise. When the laser irradiation is too close/low, adjust screws No. 3 and 4 counterclockwise.

Note: Diagrams illustrating laser adjustment are not included in this text-based conversion.

Company Information

Manufacturer/Origin: Made In China

Original Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai

Imported to USA: VEVOR STORE INC, 9448 RINCHMOND PL #E, RANCHO CUCAMONGA, California, 91730 United States of America

UK Representative: Pooledas Group Ltd, Unit 5 Albert Edward House, The Pavilions, Preston, United Kingdom

EU Representative: SHUNSHUN GmbH, Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany