VEVOR Tile Cutter

Need Help? Contact Us!

Have product questions? Need technical support? Please feel free to contact us:

? CustomerService@vevor.com

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. VEVOR will not provide further notice for any technology or software updates on our product.

Specifications

Safety Information

Symbol Guide:

• [ℹ️] Warning - To reduce the risk of injury, user must read instructions manual carefully.
• [⚠️] This symbol, placed before a safety comment, indicates a kind of precaution, warning, or danger. Ignoring this warning may lead to an accident. To reduce the risk of injury, fire, or electrocution, please follow the recommendation below.
• [?] Warning - Be sure to wear eye protectors when using this product.
• [?] Warning - Be sure to wear gloves when using this product.

General Warning: Read and understand all instructions before using this tile cutter. The operator must follow basic precautions to reduce the risk of personal injury and/or damage to the equipment. Please familiarize yourself with the hazard notices found in this manual. A notice is an alert that there is a possibility of property damage, injury or death if certain instructions are not followed.

Work Area

1. Operate in a safe work environment. Keep your work area clean, well-lit, and free of distractions.
2. Keep anyone not wearing the appropriate safety equipment away from the work area.
3. Store new tools properly in a safe and dry location to prevent rust or damage. Lock tile cutter away and keep out of the reach of children.
4. Always place the tile cutting machine on a level and firm surface.

Personal Safety

Personal Protective Equipment

1. Always wear impact safety goggles that provide front and side protection for the eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work performed.
2. Wear gloves that provide protection based on the work materials or to reduce the effects of tool vibration.
3. Caution! The edges of cut tiles are sharp.

Personal Precautions

Control the tile cutter, personal movement, and the work environment to avoid personal injury or damage to the tile cutter.

1. Do not operate any tile cutter when tired or under the influence of drugs, alcohol, or medications.
2. Avoid wearing clothes or jewelry that can become entangled with a tool's moving parts. Keep long hair covered or bound.

Specific Safety Precautions

1. The tile cutting machine is fitted with a replaceable circular blade. Keep the tile cutter and blade away from children.
2. Use the correct tile cutter for the job. This tile cutter was designed for a specific function. Do not modify or alter this tile cutter or use it for an unintended purpose.
3. After use, the machine must be stored in a safe and dry place.
4. This machine has been designed for cutting and breaking ceramic, glazed, porcelain, and polished tile, and which surface must be flat. It shall not be used for any other purpose.

WARNING! DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to the tile cutter safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.

WARNING! Direct exposure of pressurized air or fluids to skin could result in severe bodily injury.

Included Parts & Setup

SAVE THESE INSTRUCTIONS

The package includes:

• 1. Cutter (1 piece)
• 2. AAA Batteries (2 pieces)
• 3. Ruler (1 piece)
• 4. Spare Cutting Wheel (Φ22x6x6mm, 1 piece)

Battery Installation: Insert 2 AAA batteries into the device, ensuring correct polarity. Close the cap.

Operation Controls: The 'Turn on/off' switch is located on the device.

Operation

Straight Cutting

1. Place the cutting wheel on the rear edge of the tile.
2. Slide the wheel forward by pushing the handle down with medium pressure, scoring the tile surface glaze as the handle is pushed forward. It is important to make one continuous motion, scoring the surface only once per time.
3. After scoring and without moving the tile position, the breaker is slightly in the front edge of the tile and front stop. Raise the handle a little so that the breaker is flat on the tile. Apply increasing pressure on the handle until the tile snaps along the score line.

Tips: After scoring, it is better to pull back the handle to let the breaker slightly backtrack 5-10mm; this is the best position to break the tile. Do not press in the middle or the end.

Diagonal Cutting

1. Put tile on the machine against the adjusted angle ruler.
2. Place the cutting wheel on the rear edge of the tile. Slide the wheel forward by pushing the handle down with medium pressure, scoring the tile surface glaze as the handle is pushed forward. It is important to make one continuous motion, scoring the surface only once per time.
3. After scoring and without moving the tile position, the breaker is slightly in the front edge of the tile and front stop. Raise the handle a little so that the breaker is flat on the tile. Apply increasing pressure on the handle until the tile snaps along the score line.

Tips: Do not put the tile too inside to make sure the scoring line is a whole line. After scoring, it is better to pull back the handle to let the breaker slightly backtrack 5-10mm; it's the best position to break the tile.

Blade Replacement: Use a screwdriver to replace the blade.

Laser Device Instruction

The laser device requires 2pcs of AAA batteries. Please turn off the power when not in use. If the battery is exhausted, replace it.

• Laser Adjustment: There are four screws for the laser device.
• If the laser is biased to the left, adjust the No. 2 screw clockwise or the No. 1 screw counterclockwise.
• If the laser is biased to the right, adjust the No. 1 screw clockwise or the No. 2 screw counterclockwise.
• When the laser irradiation is too far/high, adjust the No. 3 and 4 screws clockwise.
• When the laser irradiation is too close/low, adjust the No. 3 and 4 screws counterclockwise.

Company Information

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai

Imported to USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK Representative: Pooledas Group Ltd, Unit 5 Albert Edward House, The Pavilions, Preston, United Kingdom

EC Representative: SHUNSHUN GmbH, Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany

Made In China