Shark VERTEX™ UltraLight Corded Stick Vacuum

Important Safety Instructions

Household Use Only

WARNING: To reduce the risk of electric shock, this vacuum cleaner has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.

General Warnings

• Your vacuum cleaner may consist of a motorized nozzle, wand, hose, and/or vacuum pod. This device contains electrical connections, electrical wiring, and moving parts that potentially present risk to the user.
• Use only identical replacement parts.
• Carefully observe and follow the instructions provided below to avoid improper use of the appliance. DO NOT use the vacuum for any purpose other than those described in this manual.
• Before use, carefully inspect all parts for any damage. DO NOT use if any parts are damaged.
• The use of an extension cord is NOT recommended.
• This vacuum cleaner contains no serviceable parts.

Use Warnings

• This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children. Keep the appliance and its cord out of reach of children. DO NOT allow the appliance to be used by children. DO NOT allow to be used as a toy. Close supervision is necessary when used near children.
• Always turn off the vacuum cleaner before connecting or disconnecting any motorized nozzles or other accessories.
• DO NOT handle plug or vacuum cleaner with wet hands.
• DO NOT use without filters in place.
• Only use Shark branded filters and accessories.
• DO NOT damage the power cord: DO NOT pull or carry vacuum cleaner by the cord or use the cord as a handle. DO NOT unplug by pulling on cord. Grasp the plug, not the cord. DO NOT run the vacuum cleaner over the power cord, close a door on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces.
• DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
• DO NOT use if nozzle or accessory airflow is restricted. If the air paths or the motorized floor nozzle become blocked, turn the vacuum cleaner off and unplug from electrical outlet. Remove all obstructions before you plug in and turn on the unit again.
• Keep nozzle and all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.
• DO NOT use if vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.
• Use extra care when cleaning on stairs.
• DO NOT leave the vacuum cleaner unattended while plugged in.
• When powered on, keep the vacuum cleaner moving over the carpet surface at all times to avoid damaging the carpet fibers.
• DO NOT place vacuum cleaner on unstable surfaces such as chairs or tables.
• Your Shark® vacuum may not be designed to stand up on its own. When taking a break from cleaning, you may need to lean it against furniture or a wall, or lay it flat on the floor. Using the vacuum for an application where the unit lacks stability may result in personal injury.
• DO NOT use to pick up: Liquids, Large objects, Hard or sharp objects (glass, nails, screws, or coins), Large quantities of dust (drywall dust, fireplace ash, or embers), Smoking or burning objects (hot coals, cigarette butts, or matches), Flammable or combustible materials (lighter fluid, gasoline, or kerosene), Toxic materials (chlorine bleach, ammonia, or drain cleaner). DO NOT use as an attachment to power tools for dust collection.
• DO NOT use in the following areas: Poorly lit areas, Wet or damp surfaces, Outdoor areas, Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust).
• Turn off all controls before plugging in or unplugging the vacuum.
• Unplug from electrical outlet when not in use and before any maintenance or cleaning.
• Hand wash with water only. Washing with cleaning chemicals could damage the unit.
• During cleaning or routine maintenance, DO NOT cut anything other than hair, fibers, or string wrapped around the brushroll.
• Allow all filters to air-dry completely before replacing in the vacuum to prevent liquid from being drawn into electric parts.
• Make sure the dust cup and all filters are in place after routine maintenance.
• If provided, secure the power cord around the two cord hooks during storage.

Assembly

1. Insert Wand into Floor Nozzle.

2. Insert Handheld Vacuum into wand.

3. For compact storage, hang the handheld vacuum from the Storage Hook on the wand.

Note: For proper operation, ensure all parts are firmly clicked into place. Accessories may vary depending on the model.

Controls

The control panel is located on top of the handheld vacuum.

• Power Button: Press the Power button to begin vacuuming. Press again to turn off power.
• Floor Type Button: Press the FLOOR TYPE button to toggle between Bare Floor and Carpet settings.

Settings

• Bare Floor Setting: For Bare Floor/Small Area Rugs. When powered on, the vacuum will be in Bare Floor setting. In this setting, the brushrolls spin slowly to clean bare floors and small area rugs.
• Carpet Setting: Press the FLOOR TYPE button to switch to Carpet setting. The brushrolls spin faster to pick up debris below the surface of your carpets. Use the floor selector to toggle between Bare Floor and Carpet settings. For deep cleaning per ASTM F 608 (embedded dirt in carpets) please use the Carpet setting. Select Carpet for stuck-on dust and debris.

Cleaning Modes

Floor Mode

To clean floors, step on floor nozzle and tilt handheld vacuum back.

Above-Floor Handheld

To detach the handheld vacuum, press the Wand Release button and lift the handheld vacuum off the wand. Great for cleaning stairs, furniture, and countertops.

Above-Floor with Wand

For more reach, detach the wand. Stand the vacuum upright, step on the Foot Pedal on the side of the nozzle, and pull up the wand to detach.

Stair Cleaning

To clean stairs or other narrow spaces, attach the handheld vacuum to the floor nozzle.

Note: All accessories are compatible with both the wand and the handheld vacuum.

Storage Mode

Handheld Storage Hook

Press the Wand Release button near the top of the wand to detach the handheld vacuum. Align the Catch on the side of the handheld vacuum with the Storage Hook on the wand, then hang the handheld vacuum from the hook. Wrap the cord around the two cord hooks. Start with the top hook, and leave a little slack in the cord.

Maintenance

IMPORTANT: Unplug the vacuum before performing any maintenance.

Emptying the Dust Cup

Empty the dust cup each time you vacuum and periodically during cleaning, when debris in the dust cup reaches the MAX fill line.

1. Press the Wand Release button and lift off the handheld vacuum.

2. Hold the dust cup over a trash receptacle. Press the 'Empty' button and pull open the dust cup lid until it clicks and locks in the open position.

3. Gently tap the cone-shaped screen inside the dust cup to dislodge dust and debris.

4. To remove the dust cup from the handheld vacuum, simultaneously press the two dust cup release buttons and slide the dust cup away.

5. To reinstall, close the lid, then insert the front end of the dust cup into the handheld vacuum first, then the back end, until it clicks into place.

Cleaning the Soft Roller

1. To remove the Soft Roller, slide the 'Eject Roller' button on the floor nozzle.

2. Tap loose debris off the Soft Roller. Use a dry towel to wipe it clean and remove debris caught in the teeth behind the roller.

3. Hand-wash the Soft Roller with water only, and allow it to air-dry completely for at least 24 hours.

4. Reinsert the Soft Roller and press it in until it clicks securely.

Note: For best performance, keep the Soft Roller clean with regular maintenance.

Cleaning Filters

Regularly rinse and replace the filters to maintain your vacuum's suction power. To prevent damage from cleaning chemicals, rinse filters with cold water only. Do not use soap. Allow all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electronic parts.

Pre-Motor Filters

With the dust cup detached, press the Filter Access buttons on both sides of the back of the dust cup, then pull out the filter housing. Pull the foam filter out of the housing, then lift out the felt filter by its pull tab. The Pre-Motor Filters should be washed once a month.

Post-Motor Filter

To access the post-motor filter, press the release latch on the filter cover on the handheld vacuum. Remove the cover and lift out the filter. The Post-Motor Filter should be washed once every 9 months.

Note: The pre-motor filters should be replaced every 2.5 years. The post-motor filter should be replaced every 3 years.

Checking for Blockages

• Check Handheld: Remove the handheld vacuum from the wand and inspect all dust cup intake openings for debris or blockages.
• Check Wand: Detach the wand and check it for blockages.
• Check Floor Nozzle: Detach the wand, tilt the floor nozzle back, and check openings for blockages. Specifically, check the Debris Intake. Pinch the tabs on the bottom of the nozzle to open the cover, lift up the intake tube, clear any blockages, push the tube down, and press the nozzle cover closed until it clicks.

Floor Nozzle Maintenance

Self-Cleaning Brushroll: If hair wrap occurs, continue vacuuming; the brushroll automatically removes it. If some hair remains, carefully clear it away.

Debris Intake: Check the Debris Intake and clear away any dirt or blockages. Push the cover down until it clicks into place.

Troubleshooting

Vacuum is not picking up debris. No suction or light suction.

• Empty the dust cup.
• Check filters to see if they need cleaning. Follow instructions for rinsing and completely air-drying the filters before reinstalling them.
• Clear any blockages in the nozzle, wand, handheld vacuum, or accessories. See Checking for Blockages section for more information.
• If any string, hair, or carpet fibers remain wrapped around the brushroll after continued use, carefully clear them away.

Vacuum lifts area rugs.

Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges. Turn off the unit to disengage the brushrolls. To restart, press the power button on the handle.

Note: During above-floor cleaning, accessories are optimized for different types of debris.

Vacuum nozzle stops working or the indicator light is red.

If the brushroll indicator light turns solid red, immediately turn off and unplug the vacuum. Disconnect the wand from the floor nozzle and clear any blockages. Reconnect the wand, plug in the vacuum, and turn on the power. If the brushroll indicator light on the floor nozzle is green, the blockage has been successfully cleared. If the light is still red, please contact a service center.

Vacuum turns off on its own or the indicator light flashes red.

If your vacuum overheats, the thermostat will automatically turn off the motor. Perform the following steps to restart:

1. Turn off the vacuum and unplug it.
2. Empty the dust cup and clean the filters. See Emptying the Dust Cup and Cleaning Filters sections.
3. Check for blockages in the wand, floor nozzle, handheld vacuum, inlet openings, and accessories.
4. Reassemble the entire vacuum and ensure all parts click into place.
5. Allow unit to cool for a minimum of 60 minutes.
6. Plug in vacuum and turn it on.

Vacuum is making a loud noise.

If you vacuum up a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught behind the brushroll. See Checking for Blockages section for more information.

Handheld vacuum is warm.

Due to the strong suction power of the vacuum, it is normal to experience warmth around the filter exhaust area after use. Turn off the vacuum and wait for 10 minutes for it to cool down. If the warmth continues, clean the pre-motor and post motor filters. Refer to the Maintenance section for filter cleaning instructions.

Technical Specifications

Voltage: 120V~, 60Hz