GIGABYTE GS34WQC Gaming Monitor User Guide

Package Contents

The following items come with your packaging box. If any of them is missing, please contact your local dealer.

• Monitor
• Monitor Base
• Stand
• Power Cable
• DP Cable
• Screws
• Warranty Card
• Quick Start Guide

Note: Please keep the packaging box and packing materials for possible transportation of the monitor.

Rear View

The rear of the monitor features several ports and controls:

• 1 HDMI ports (x2)
• 2 DisplayPort
• 3 Headphone jack
• 4 AC IN jack
• 5 Control button
• 6 Kensington lock

A Power LED indicates the monitor's status.

Installing the Stand Base

1. Place the monitor on the lower EPS foam, with the screen facing down.
2. Install the stand onto the base and fasten it with the thumb screw from the bottom of the base.
3. Align the monitor stand with the rear housing hole and lock it on the rear housing with four screws. Then install the base onto the stand.
4. Lift the monitor to an upright position and place it on a table. The monitor's height may be adjusted after certain components are removed.

Adjusting the Viewing Angle

Adjusting the Tilt Angle

1. Place one hand on the base to prevent the monitor from tipping over during the adjustment.
2. Place the other hand on the top-center of the screen and apply forward or backward pressure to adjust the angle to the desired viewing angle (-5° to 20°).

Adjusting the Screen Orientation

Raise the screen to the maximum height (100 mm).

Installing a Wall-Mount Bracket (Optional)

Use only a 100 x 100 mm compliant wall mount kit. Install the wall mount according to the manufacturer's instructions.

1. Position the monitor face down with its protective foam or with a nonabrasive cloth underneath.
2. Align the wall-mount bracket installation holes with the screw holes on the back of the monitor.
3. Use the screws to secure the bracket in place.

Note: To mount the monitor on the wall, refer to the installation guide included with the wall-mount bracket kit. The monitor supports 100 mm mounting holes that comply with VESA industrial standards. For third-party solutions, four 4 mm screws with a pitch of 0.7 mm and a length of 10 mm are required. Using longer screws may damage the monitor. Ensure the bracket complies with VESA standards and can support the monitor body. Use the provided power and video cables for optimal performance.

Turning the Power On/Off

Power On

1. Connect one end of the power cable to the AC IN jack at the rear of the monitor.
2. Connect the other end of the power cable to a power outlet.
3. Press the Control button to turn on the monitor. The Power LED will light white, indicating the monitor is ready to use.

Note: If the power LED fails to turn on, check the LED settings in the Settings menu (refer to page 20).

Power Off

Press the Control button for 2 seconds to turn off the monitor. Alternatively, when the Main menu is displayed, move the Control button down (↓) to turn off the monitor (refer to page 13).

Selecting the Input Source

1. Move the Control button right (→) to enter the Input menu.
2. Move the Control button center (●) to select the desired input source, then press the Control button to confirm.

Quick Menu

Hot Key

By default, the Control button is assigned specific functions. To change these, refer to the "Quick Switch" section on page 20.

Accessing Hot Key Functions:

• Move the Control button up (↑) to enter the Black Equalizer menu. Use the Control button up/down (↑/↓) to adjust the setting and press the Control button to confirm.
• Move the Control button down (↓) to enter the Picture Mode menu. Use the Control button center (●) to select the desired option and press the Control button to confirm. Available Picture Modes include: Standard, Gaming, Movie, Reader, sRGB, Custom, ECO.
• Move the Control button left (←) to enter the Crosshair menu. Use the Control button up/down (↑/↓) to select the desired option (OFF, Style 1, Style 2, Style 3, Style 4) and press the Control button to confirm.
• Move the Control button right (→) to enter the Input menu.

Note: To close a menu, move the Control button left (←).

Function Key Guide

Press the Control button to display the Main menu. The menu includes options for Settings, Crosshair, Game Assist, Exit, and Power Off. Use the Control button to navigate and select functions.

Game Assist

When the Main menu is displayed, move the Control button right (→) to enter the Game Assist menu. This menu allows configuration of game-related settings:

• Game Info: Configure FPS (First Person Shooting) game settings.
• Gaming Timer: Select countdown timer mode. Set to OFF to disable.
• Refresh Rate: Enable/disable real-time refresh rate display.
• Info Location: Specify the location of the information on the screen.

Configure the Device Settings

When the Main menu is displayed, move the Control button up (↑) to enter the Settings menu. Use the Control button to navigate and make adjustments.

Gaming Settings

Configure game-related settings:

• Aim Stabilizer: Reduces motion blur in fast-moving games. Note: Not available when frequency is below 100Hz or when FreeSync Premium is activated.
• Black Equalizer: Adjusts the brightness of dark areas.
• Super Resolution: Sharpens low-resolution images.
• Display Mode: Select aspect ratio. Options include Full (fills the screen) and Aspect (displays without geometric distortion). Note: Not compatible with FreeSync Premium and PIP/PBP functions.
• Overdrive: Improves response time.
• FreeSync Premium: Eliminates screen lag and tearing during gameplay.

Picture Settings

Configure image-related settings:

• Standard: For documents or browsing.
• Gaming: For playing games.
• Movie: For watching movies.
• Reader: For viewing documents.
• sRGB: For viewing photos and graphics.
• Custom: For customized picture mode settings.
• ECO: For energy saving.

Note: The "Standard" picture mode and "Low Blue Light Level 10" are optimized settings compliant with TUV Low Blue Light Certification.

Display Settings

Configure display screen settings:

• Input: Select the input source (HDMI 1, HDMI 2, DisplayPort).
• Overclock: Select ON/OFF.
• RGB Range: Select RGB range setting or auto-detect (only available for HDMI input).
• Overscan: Enlarges the input image slightly to hide outermost edges.

PIP/PBP Settings

Configure multi-image settings:

• OFF: Disables PIP/PBP.
• PIP (Picture-in-Picture): Divides the screen into two parts (main and inserted window). Settings include Signal source, PIP size, Position, Display switch, and Audio switch.
• PBP (Picture-by-Picture): Displays a 1x1 split screen (left and right windows). Settings include Signal source, PBP size, Display switch, and Audio switch.

Note: PIP/PBP is not compatible with HDR and FreeSync Premium functions.

System Settings

Configure system-related settings:

• Audio: Configure headphone settings (Volume, Mute).
• OSD Settings: Configure on-screen display menu settings, including Display Time, OSD Transparency, and OSD Lock. If OSD Lock is enabled, no OSD adjustment is allowed. To disable OSD Lock, press the Control key and confirm with 'Yes'.
• Quick Switch: Assign functions to hot keys (Aim Stabilizer, Black Equalizer, Crosshair, Low Blue Light, Volume, Input, Contrast, Brightness, Picture Mode). Default assignments: Up (↑) for Black Equalizer, Down (↓) for Picture Mode, Right (→) for Input, Left (←) for Crosshair.
• Other Settings:
  • Resolution Notice: Displays current resolution when switching input sources.
  • Input Auto Switch: Automatically switches to an available input source.
  • Auto Power Off: Turns off the monitor after a set time.
  • LED Indicator: Configures the Power LED behavior (Always OFF, Always ON, Standby ON).
  • Quick Boot: Improves the boot-up speed of the screen.

Language Settings

Select an available language for the OSD menu.

Reset All

Restores the monitor to its factory default settings.

Specifications

Note: Specifications subject to change without notice.

Supported Timing List

Troubleshooting

Note: If the problem persists, please contact customer service for further assistance.

Basic Care

• Wipe the screen with a soft, lint-free cloth to remove any residual dust.
• Spray or apply cleaning fluid onto a soft cloth, then wipe the screen gently with the damp cloth.

Note: Ensure the cloth is damp, but not wet. Avoid applying excessive pressure on the screen. Acidic or abrasive cleaners can damage the screen.

GIGABYTE Service Information

For more service information, please visit the GIGABYTE official website: https://www.gigabyte.com/

Safety Precautions

Read through the following Safety Precautions before using the monitor:

• Only use accessories provided with the monitor or recommended by the manufacturer.
• Keep plastic packaging away from children.
• Before connecting to a power outlet, ensure the power cable's voltage rating is compatible with your location's power specification.
• Connect the power cord plug to a properly wired and grounded power outlet.
• Do not touch the plug with wet hands to avoid electric shock.
• Place the monitor in a stable and well-ventilated area.
• Do not place the monitor near heat sources like electric radiators or direct sunlight.
• Do not cover or block ventilation holes.
• Do not use the monitor near water, drinks, or liquids to prevent electric shock or damage.
• Unplug the monitor before cleaning.
• Avoid touching the screen surface with hard or sharp objects as it can be easily scratched.
• Use a soft lint-free cloth for cleaning. A glass cleaner may be used if necessary, but never spray directly onto the screen.
• Disconnect the power cable if the monitor will not be used for an extended period.
• Do not attempt to disassemble or repair the monitor yourself.

Stability Hazard Precautions

The product may fall, causing serious personal injury or death. To prevent injury, this product must be securely attached to the floor/wall according to installation instructions. Many injuries, especially to children, can be avoided by taking simple precautions:

• Always use stands or installation methods recommended by the manufacturer.
• Always use furniture that can safely support the product.
• Ensure the product does not overhang the edge of supporting furniture.
• Educate children about the dangers of climbing on furniture.
• Route cords and cables so they cannot be tripped over or pulled.
• Never place the product in an unstable location.
• Never place the product on tall furniture without anchoring both the furniture and the product.
• Never place the product on cloth or other materials between the product and furniture.
• Never place items that might tempt children to climb (toys, remotes) on top of the product or furniture.
• If relocating the product, apply the same considerations.
• To prevent injury or damage from tipping due to shocks (e.g., earthquakes), install in a stable location and take measures to prevent falling.

User Comfort Recommendations

The monitor uses Flicker-Free technology to reduce eye strain and fatigue. For comfortable viewing:

• Optimal viewing distances range from approximately 510 mm to 760 mm (20" to 30").
• Position the monitor so the top of the screen is at or slightly below eye-height when seated comfortably.
• Use adequate lighting for your task.
• Take regular breaks (at least 10 minutes) every half-hour.
• During breaks, look away from the screen at a far object for at least 20 seconds.
• Perform eye exercises: (1) look up and down, (2) roll eyes slowly, (3) move eyes diagonally.

This model has passed Flicker Free and Low Blue Light verification by TUV Rheinland. Learn more: https://www.gigabyte.com/tw/Support/FAQ/4310

This section contains regulatory compliance statements for various regions, including the United States (FCC), Canada (DOC), and European Union (CE, RoHS, WEEE). It also includes compliance information for India (E-waste) and Japan (VCCI).

United States, FCC Statement: This equipment complies with Part 15 of the FCC Rules for Class B digital devices, designed to provide reasonable protection against harmful interference in residential installations. If interference occurs, users are encouraged to reorient the antenna, increase separation, connect to a different circuit, or consult a technician.

Canadian Department of Communications Statement: This digital apparatus complies with Canadian ICES-003.

European Union (EU) CE Declaration of Conformity: This device complies with directives such as EMC (2014/30/EU), Low-voltage (2014/35/EU), ErP (2009/125/EC), and RoHS (2011/65/EU & 2015/863). Compliance is assessed using harmonized European Standards.

European Union (EU) RoHS Statement: GIGABYTE products are manufactured without hazardous substances like Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP, DBP, and DIBP, meeting RoHS requirements.

WEEE Directive Statement: GIGABYTE adheres to the WEEE directive for the proper treatment, collection, recycling, and disposal of electronic equipment. Products must not be disposed of with general waste; they should be taken to designated collection centers.

India RoHS: This product complies with the "India E-waste (Management and Handling) Rule 2011", prohibiting certain hazardous substances above specified concentrations, with exceptions as noted.

Japan Class 01 Equipment Statement & VCCI Class B Statement: These statements provide compliance information for Japanese regulations regarding grounding and electromagnetic interference.

China RoHS Compliance Statement: This statement details the environment-friendly use period and lists the presence of hazardous substances in product components according to Chinese regulations.