Important Safety Information & Preparation
General Safety: Read all instructions thoroughly before handling or assembling the product. Retain these instructions for future reference. For your safety, this product must be used with the provided anti-tip device. Installation must be performed by a competent person. Incorrect installation can lead to danger, injury, or property damage. Keep small parts away from children and do not leave children unattended in the assembly area. Furniture tip-over can cause serious or fatal crushing injuries. To prevent tipping, the unit must be permanently fixed to the wall using appropriate wall fixings (not included). Do not overtighten fixings as this may damage the product. Be careful of sharp edges and wear gloves during installation.
Preparation: Ensure all parts are present before starting. Check packaging carefully as components may be concealed. Do not dispose of packaging until all parts are located. Do not use knives to open boxes. Clear a spacious, clean, and dry area for assembly. Have the right tools ready. If any pre-installation work (e.g., electrical, gas, water) is required, ensure it is carried out by a qualified person in compliance with local regulations.
Parts List
| Part Code | Description | Quantity |
|---|---|---|
| 01 | Base Panel | x1 |
| 02 | Top Panel | x1 |
| 03 | Side Panel | x1 |
| 04 | Side Panel | x1 |
| 05 | Back Panel Support | x3 |
| A | Fastener (e.g., Cam Bolt) | x10 |
| B | Fastener (e.g., Dowel/Screw) | x6 |
| D | Screw | x68 |
| F | Drawer Runner (Cabinet Side) | x2 |
| I | Drawer Runner (Cabinet Side) | x2 |
| J | Screw | x2 |
| K | Drawer Runner (Cabinet Side) | x2 |
| M | Adjustment Screw | x4 |
| N | Drawer Runner (Drawer Side) | x1 |
| P | Fastener (e.g., Cam Lock) | x12 |
| T | Screw | x2 |
| U | Fastener | x4 |
| V | Fastener (e.g., Cam Lock) | x6 |
Assembly Instructions
Step 01: Attach Side Panels to Base
Action: Connect side panels (03, 04) to the base panel (01) using fasteners (A). Ensure panels are correctly oriented as per the diagram.
Step 02: Install Drawer Runners on Side Panels
Action: Attach drawer runners (01, 02) to the inner sides of panels (03, 04) using screws (D) and cam locks (P, V). Pay close attention to the diagram for correct placement and orientation.
Step 03: Insert Back Panel Supports
Action: Slide back panel supports (05) into the designated slots on the side panels (03, 04) and secure them with fasteners (B).
Step 04: Attach Top Panel
Action: Place the top panel (02) onto the assembled side panels (03, 04) and secure it using fasteners (B).
Step 05: Prepare Drawer Runners (Cabinet & Drawer Sides)
Action: (Recommendation) Seal any raw edges with silicone sealer. Attach the cabinet-side drawer runners (F, I) to the side panels of the cabinet structure using screws (D). Attach the drawer-side runners (N) to the drawer boxes using screws (D). Note the 15mm measurement for runner placement on drawer sides.
Step 06: Attach Back Panel
Action: Secure the back panel (not explicitly numbered but shown in diagrams) to the cabinet frame using screws (D).
Step 07: Install Drawer Runners in Cabinet
Action: Insert the remaining drawer runners (K) into the pre-drilled holes on the inside of the cabinet side panels. Secure them with screws (D, J).
Step 08: Assemble Drawer Boxes
Action: Assemble the drawer boxes by connecting drawer sides (08, 09) to the drawer front/back panels (10) using fasteners (D, T, U). Repeat for all drawers (x3).
Step 09: Attach Drawer Fronts
Action: Attach the drawer fronts to the assembled drawer boxes. Ensure correct alignment and secure using appropriate fasteners.
Step 10: Install Drawers and Adjust Leveling
Action: Slide the assembled drawers into the cabinet runners. Use the adjustment screws (M) to level the drawers and ensure smooth operation. The diagram shows a close-up of the adjustment mechanism.
Step 11: Completed Cabinet
Description: The diagram shows the fully assembled base cabinet with all drawers installed.
Step 12: Final Check and Adjustment
Description: The diagram shows the cabinet with drawers, highlighting the adjustment screws (M) for fine-tuning the drawer level and alignment, indicated by +/- 1.5mm adjustments.
Guarantee Information
This product comes with a 2-year manufacturer's guarantee against manufacturing defects, valid from the date of purchase for normal household use. To make a claim, you must present proof of purchase. The guarantee covers product failures and malfunctions provided the product is used as intended and maintained according to instructions. It does not cover normal wear and tear, misuse, or accidental damage. This guarantee is in addition to, and does not affect, your statutory rights. For queries, contact the store where the product was purchased.
Manufacturer & Support
UK Manufacturer: Kingfisher International Products Limited, 1 Paddington Square, London, W2 1GG, United Kingdom
EU Manufacturer: Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011VM Amsterdam, The Netherlands
For online instruction manuals and product information, visit: www.kingfisher.com/products
Turkey Importer: KOÇTAŞ YAPI MARKETLER TİCARET A.Ş.
For support and spare parts in Turkey, contact Koçtaş Customer Services at 0850 209 50 50.
