Product Overview

A diagram shows the VEVOR S12C Hydroponic Grow Kit. The system consists of a base unit containing a water reservoir and control panel, topped with a stand supporting an adjustable LED grow light. The base has multiple planting sites.

Need Help? Contact Us!

For product questions or technical support, please contact:

Technical Support and E-Warranty Certificate: www.vevor.com/support

WARNING

To reduce the risk of injury, the user must read the instructions manual carefully before using the product.

Notes before Installation: Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

1. Non-professional technicians should not repair or modify this product without authorization. Contact a qualified electrician for installation.
2. Turn off the power and follow proper procedures before installation to avoid improper operation and risk of electric shock.
3. To ensure the product's lifetime, do not use it in a place with strong acid mist.
4. Check if the voltage marked on the luminaire is consistent with the input voltage to be connected to avoid electric shock and damage to the luminaire.
5. Ensure installation on a flat place without vibration, swinging, or fire hazards.
6. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
7. DO NOT use an extension cord near water or wherever water may accumulate.
8. This appliance can be used by children aged 8 years and above, and persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, if they have been given supervision or instruction concerning safe use and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be performed by children without supervision.
9. The luminaire shall be positioned such that prolonged gazing at it is not permitted.

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

Before using the product, please read the instructions carefully and keep them properly.

Note: Please ensure that children are always supervised by an adult when using this product. After adding water, make sure your hands are dry before plugging the adapter into a power source. The machine requires water in the tank and a 12V DC power supply to operate.

To prevent any damage to the machine, ensure that no electrical components are directly exposed to water. If water splashes onto or spills onto any electrical components, thoroughly dry all related parts.

COMPONENTS

• Planting Machine (x1)
• Planting Basket (x13)
• Planting Sponge (x15)
• Circular Seedling Lid (x13)
• Identification labels (x12)
• Support bar (x4)
• Top cover (x6)
• A&B Nutrient Solution (x1)
• Filling funnel (x1)
• Water Level Indicator (x1)
• Adaptor (x1)

Unboxing guide

1. Remove the machine from the packaging box. Pull up the extendable pole of the lamp surface.

   Note: Lift the extendable pole with one hand and hold the water tank with the other hand to prevent lifting the entire device.

2. Remove the water tank lid and take out the accessories from the water tank, such as the adapter, planting basket, planting sponge, etc.

How to plant

1. Prepare nutrient solution. Follow the instructions on the 2 bottles of nutrients in the accessories box.

   Diagram description: Shows bottles labeled 'A' and 'B' with '+' signs indicating mixing.

2. Install the water level indicator and filling funnel.

   Diagram description: Shows the water level indicator and filling funnel being inserted into the planting lid.

3. Add water through the water injection port, ensuring the water level indicator does not exceed the maximum line.

   Diagram description: Shows water being poured into the machine via the filling funnel.

4. Install the planting basket and planting sponge. Soak the sponge in water for 5 minutes. Then, place the seeds in the sponge. For normal germination, it is recommended to soak seeds in warm water for about 1 hour before sowing them in the planting sponge. Place the basket into the water tank lid.

   Diagram description: Shows a hand placing a seed into a planting sponge within a basket, and then placing the basket into the lid.

5. Insert the adapter, then press the power button. The light will turn on, and the machine will start working. The light automatically turns on for 12 hours and off for 12 hours. This cycle setting is active only when the cycle function is turned on.

   Note 1: Make sure your hands are dry before inserting the adapter.

   Note 2: Light is not needed before seeds germinate. Turn on the light after the seeds have germinated.

Control Panel Description

The control panel features several indicators and buttons:

• 1. Fertilization Display: Shows the number of days remaining until fertilization is needed.
• 2. Time Display: Adjustable planting time.
• 3. Humidity Display: Sensor Intelligent Display for humidity.
• 4. Temperature Display: Sensor Intelligent Display for temperature.
• 5. Plant Times Button: Press to change the growing days.
• 6. Power Button: Activates the 12-hour on/12-hour off automatic light cycle.
• 7. [plant-icon] Button: Sets the light to 8 hours on/16 hours off.
• 8. [mode-icon] Button: Sets the light to 14 hours on/10 hours off.
• 9. [+] Button: Adjusts planting time, growing days, and fertilization days.
• 10. [-] Button: Adjusts planting time, growing days, and fertilization days.
• 11. Menu Button: Tap to switch between planting time, growing days, or fertilization days.

Long press the Menu button for five seconds to reset the growing days and fertilization days; the time setting remains unchanged.

Made In China