Assembly Instruction
STORAGE BENCH
If you have any questions, please feel free to contact us.
Email:hdteam @aminalife.com
Model Number: N715P293344
IMPORTANT NOTE :
- PLACE ALL PARTS ON A CLEAN AND SMOOTH SURFACE SUCH AS A RUG OR CARPET TO AVOID THE PARTS FROM BEING SCRATCHED.
- BEFORE YOU BEGIN, KINDLY FOLLOW THE ASSEMBLY INSTRUCTIONS STEP BY STEP.
- DO NOT TIGHTEN ALL SCREWS AND BOLTS UNTIL THE TABLE IS FULLY SET-UP
Detail View
Please read these instructions fully before starting assembly:
- Check you have all the components and tools listed on the following pages.
- Keep children and animals away from the work area, small parts could choke if swallowed.
- Remove all fittings from the plastic bags and separate them into their groups.
- Make sure you have enough space to layout the parts before starting.
- During assembly do not stand or put weight on the product, this could cause damage.
- Assemble the item as close to its final position (in the same room) as possible.
- Assemble on a soft level surface to avoid damaging the unit or your floor.
- Parts of the assembly will be easier with 2 people.
- To reduce the likelihood of damaging your product please ensure that your power drill is set on a low torque setting.
- Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts
- Regularly check and ensure That all bolts and fittings are tightend properly.
- Please do not place items that exceed the load capacity.
Care and maintenance:
Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
PART LIST
- 1 CUSHION (1pc)
- 2 TOP FRAME (1pc)
- 3 BOTTOM SHELF (1pc)
- 4 BACK FRAME (1pc)
- 5 RIGHT SIDE FRAME (1pc)
- 6 LEFT SIDE FRAME (1pc)
- 7 FRONT FRAME (1pc)
- 8 CENTER SUPPORT DRAWER (2pcs)
- 9 LEFT SUPPORT DRAWER (1pc)
- 10 RIGHT SUPPORT DRAWER (1pc)
- 11 LEGS (4pcs)
- 12 FRONT DRAWER (3pcs)
- 13 BACK DRAWER (3pcs)
- 14 SIDE DRAWER (6pcs)
- 15 BOTTOM DRAWER (3pcs)
HARDWARE LIST
- A BOLT (8pcs) - Ø1/4" x 35mm
- B SPRING WASHER (8pcs) - Ø1/4"x11mm
- C FLAT WASHER (8pcs) - Ø1/4"x19mm
- D ALLENKEY (1pc) - 4 mm
- E WOOD SCREW (20pcs) - #4x15mm
- F WOOD SCREW (48pcs) - #4x25mm
- G HOLES (2pcs)
- H FOLDED (1pc)
- I HANDLE (3pcs) - Ø5/32x28mm
- J HANDLE BOLT (3pcs)
Assembly Steps
Step 1
Attach side frames (5, 6) to the back frame (7) using bolts (A), spring washers (B), and flat washers (C). Use Allen key (D) for tightening.
Hardware used: 4x A, 4x B, 4x C, 1x D
Step 2
Attach center support drawers (8) to the side frames (5, 6) and back frame (7) using bolts (A), spring washers (B), and flat washers (C). Use Allen key (D) for tightening.
Hardware used: 4x A, 4x B, 4x C, 1x D
Step 3
Attach the front frame (7) to the side frames (5, 6) using bolts (A), spring washers (B), and flat washers (C). Use Allen key (D) for tightening.
Hardware used: 4x A, 4x B, 4x C, 1x D
Step 4
Attach the legs (11) to the bottom of the assembled frame.
Hardware used: 4x Legs (11)
Step 5
Place the bottom shelf (3) onto the assembled frame and secure it using wood screws (G).
Hardware used: 4x G
Step 6
Attach the top frame (2) to the assembled unit using wood screws (G) and wood screws (E). Also, attach the folded part (F) to the top frame.
Hardware used: 14x G, 2x E, 1x F
Step 7
Attach the top frame (2) to the side frames (5) and back frame (7) using wood screws (G) and folded part (F).
Hardware used: 2x G, 1x F
Step 8
Assemble the drawers. Attach side drawers (14) to the back drawer (13) and bottom drawer (15) using wood screws (H).
Hardware used: 24x H
Step 9
Continue assembling the drawers. Attach side drawers (14) to the back drawer (13) and bottom drawer (15) using wood screws (H).
Hardware used: 24x H
Step 10
Attach the handles (I) to the front drawers (12) using handle bolts (J).
Hardware used: 3x I, 3x J
Step 11
Insert the assembled drawers (12) into the storage bench.
Complete
Your storage bench is now assembled.
