User Manual for BAANOOL models including: BAANOOL, 405CD, GPS Tracker, Vehicle Tracker, Asset Tracking, User Manual, Installation Guide, SMS Commands
新GPS103AB型说明书
A
[PDF] GPS Tracker User Manual - Global Sources
Google Play、App Store search “BAANOOL IOT” to download it. Register. Open BAANOOL IOT, register a new account and login, Choose “BAANOOL car “to enter it.
GPS Tracker User Manual
Thank you for purchasing the tracker. This manual shows how to operate the device correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual.Any change will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.
405CD-V1.2
1 Specifications
Product name Model DIM. Weight Network
Band
GPS sensitivity GPS accuracy
Time To First Fix
Applicable car power Battery Storage Temp. Operation Temp. Humidity
GPS TRACKER 405CD 9.6×5.4×1.9cm 70g GSM/GPRS/WCDMA/LTE 4GB1/B2/B3/B4/B5/B7/B8/B28A/B28B/B40 3GB1/B2/B5/B8 2G850/900/1800/1900Mhz -165dBm 5m
Cold status 45s Warm status 35s Hot status 1s
12V-24V Chargeable 3.7V 90mAh Li-ion battery
-40°C to +85°C -20°C to +45°C 5%--95% non-condensing
2 Hardware Description
Status light
SIM card slot
3 Terminal Installation
1. Please ask a qualified engineer to install it. 2. The installation environment should ensure that the GSM and GPS signals are good 3. Please do not install it in a dusty and humid environment. 4. Find the 14PIN wiring harness provided with the product, insert it into the corresponding wiring
hole of the product, and connect to the original car circuit as shown in the following Wiring Diagram
1
5. The pink wire can be connected to the original car alarm horn or the alarm horn purchased together.
6. Understand that the vehicle door trigger type is positive trigger or negative trigger. Connected to the green wire if it is positive trigger, and connected to the blue wire if it is negative trigger.
7. The gray wire is connected to the temperature and humidity sensor, the red and black wires are connected to the temperature and humidity sensor power supply.
8. Please install the SOS button where the driver can touch it. 9. SIM card installationOpen sealed buckle of sim card, insert the sim card , then ,Put sealed
buckle back. Please be sure to confirm that the SIM card network frequency band is the network frequency band supported by the tracker. Caller ID must be turned on and the PIN code must be turned off. The call forwarding function cannot be turned on.
10. After inserting the SIM card, connect the positive and negative (red and black) wires of the power supply to the 12V or 24V power supply of the car. Wait the device works normally After 1 minute of power-on.
4 Device Status Light
Indicators Power LED (Red)
GSM LED (Green)
Flash Always ON OFF Always ON Flash 1 time each second Flash 2 times each second
Status
Low battery Charging Fully charged No GSM signal GSM signal ok GSM signal okGPS signal ok
5 This tracker supports mobile APP, web server,Bluetooth and SMS to track and manage in multiple ways.
2
If use the mobile APP and web server, need a SIM card activated a data package or use a data sim card. If use SMS mode, need SIM card activated functions of SMS, voice call, and call display is on
6 Mobile APP
Scan the QR code to download APP
Google PlayApp Store search "BAANOOL IOT" to download it Register Open BAANOOL IOT, register a new account and login, Choose "BAANOOL car "to enter it.
Bind Device click this button(show in the picture below) to add the device or scan the QR CODE on the device or enter the IMEI manually to bind the device.
Click to add the device
Scan QR CODE or enter the IMEI
use the device Usually, the device can automatically select the APN,username and password without setting it. If the device is still offline after 3 minutes of binding, you need to set the APN and username and password in Bluetooth or SMS according to 11.19 and 11.20. After the device comes GPRS online normally, you can view and manage the device.
7 BAANOOL IOT's Web Server
3
Open www.baanooliot.com , The login account name and password is the same as mobile App's
8 Mobile APP and web server functions
8.1 Positioning Strategy
You can click "tracking" button to select the working mode and tracking interval, when not move, set
a longer time interval to report the location (eg: 1 hour), when move, you can set a short time interval
for report location frequently(eg: 10 seconds).when gps device is moving will show the motion trace.
8.1.1 Work Mode
Work mode
Descriptions
GPRS is always online, GPS device report location according to the set
Real time tracking
time interval. When moving or not move GPRS always online is defaulted, and report location every 10 seconds
when moving or report location every hour when not move.
GPRS offline when not move (phone calls, SMS messages, and alarms
triggered get GPRS online, SOS/door open alarm /illegal ignition
Smart mode
alarms are triggered, the device will be always GPRS online until these alarms cancled ).
when moving, GPS device Wake up and go online , no matter move or
not move, the device will report location at the set time interval.
8.1.2 Tracking Time Interval
8.2 Playback
you can click "playback" to check the history motion trace
4
8.3 Remote Immobilizing
no quick Remote immobilizing, Remote immobilizing quickly ,Remote fuel resume
8.4 Arm/Disarm
armSilent Armingdisarm
8.5 Alarm function in arming state
8.5.1 Door Opening Alarm When the door is opened in arming state, tracker will send SMS notification "Door alarm+latitude & longitude" to authorized numbers. The siren will beep for 20 seconds, and if the door is still open, then the siren will beep for another 20 seconds with 20 seconds pause, disarming to quit the alarm. 8.5.2 ACC Alarm In arming state, if the ignition of the vehicle has been switched "ON"(Key is rotated to "ACC ON" position or vehicle is started, ignition alarm is triggered,The siren will beep for 20 seconds, and if the ignition is still on, then the siren will beep for another 20 seconds with 20 seconds pause, disarming to quite the alarm. 8.5.3 Shock Alarm In arming state,the tracker detect the movement and shock, will send "Sensor alarm + latitude / longitude" to authorized numbers, and only send once in 3 minutes. Siren will beep for 5 seconds for the first trigger and second trigger, and then ,Siren beep 10 seconds for another trigger,
8.6 Other Alarms
8.6.1 Low Battery Alarm when the battery voltage is close to 3.55V, tracker will send message"low battery + latitude & longitude" to authorized numbers for 2 times at 15 minutes interval. 8.6.2 External Power Alarm This function activate by default. Tracker will send "Power alarm+latitude& longitude" to authorized numbers when external power disconnected. 8.6.3 SOS Alarm
Press SOS button for 3 seconds(For model B/D, press key on the remote control), tracker will
send SMS notification "Help me+latitude& longitude" to all the authorized numbers. 8.6.4 Geo-fence After Several Geo-fences are set on APP or web serverGeo-fence alarm will be triggered When the
5
tracker move out or move in these Geo-fences.
8.6.5 Movement Alarm on platform ,you can draw a circle regarding the device current position as the center. When the device leaves the current position and exceeds the circle range, Movement alarm will be triggered.
8.6.6 Over speed Alarm After set up the speed value (km/h), over speed alarm will be triggered. when the device runs over the speed set before 8.6.7 Fuel Alarm When the vehicle's fuel consumption exceeds the normal standard while the vehicle is running, or there is fuel leakage or fuel stealing when the vehicle is stopped, tracker will send "oil: ××%+latitude & longitude" to the authorized numbers. The siren will beep for 20 seconds. 8.6.8 Temperature Alarm (Option) When the device operating temperature exceeds the set temperature range, the device will trigger temperature alarm. The available temperature range is from -40 to 80.
8.7 WiFi hotspot (For C/D model)
This function is deactivated by default. When the hotspot is turned on, user's other devices can use the wifi name and password to connect to the Internet. If a camera is installed, the hotspot should be turned on to use the photography and video functions.
8.8 WiFi camera (Optional for C/D model)
8.8.1 Configure the network for the camera Open the app After turn on the wifi hotspot in the APP menu, the hotspot name will come out, Click the hotspot name will display the QR code for Network configuration. Point the camera at the QR code to scan the code,The camera prompts "Network configuration successful". 8.8.2 Photography function When the vehicle detects DOOR/ACC/SOS alarm, the device will report alarms and automatically turn on the camera, then, upload the captured photos to the monitoring platform and send the link of photos to all authorized numbers.
6
8.8.3 View real-time video Both the monitoring platform and APP can open a live video stream to view the surrounding environment of the vehicle.When the video is playing, you can click the camera button to capture video frames. Audio is off by default, you can click the mute button to turn on real-time audio. 8.8.4 Video playback You can view the video playback on the App, and the playback is muted by default. Click the mute button to turn on the sound.
8.9 Listen
You can listen for 15 second each time set this function.
8.10 Bluetooth configuration parameters
You can click the Bluetooth icon on the App login page or the home page after login to enter the Bluetooth configuration parameter function interface, and click "Bn405" to directly modify device parameters after the connection is successful.All SMS commands can be set via Bluetooth.
8.11 Other functions
You can control functions of deactivate alarm, SIM Card Balance enquiry, firmware update, restart, initialization Settings. and set shock sensitivity, authorization, times of alarm, time zone, external power on /off, Fuel sensor calibrating, vibration sensitivity, angle, SMS password, and check device details, Operation record, installation.
9 Bluetooth automatic arm/disarm
Open the phone Settings, find the Bluetooth menu, open Bluetooth, search for Bluetooth named "Bn405", click Connect, enter the machine password, and then the pairing succeeds. When you are far away from the terminal and the Bluetooth connection is disconnected, the terminal automatically arm. When close to the terminal, Bluetooth automatically connected, the terminal automatically disarm. Note: When using other methods (remote control, SMS command, app, web version, Bluetooth setting parameters) after arm, Bluetooth sensor automatic arm/disarm will be invalid, until through other means of disarm, Bluetooth sensor automatic arm. If you do not use Bluetooth sensing, please unpair in the Bluetooth menu of your phone.
10 Remote controllerFor D model
Key Function Descriptions Arming Press for 0.5 second, siren beep one time .If the vehicle is in the
7
Disarmin g
Silent arming
SOS
Deterrenc e/Car locate
ignition state(Represents ths key not pulled),it cannot enter the armed state ,siren not beep
Press for 0.5 second, siren beep 2 times, all alarms are stopped
Press for 0.5 second in disarm state, siren beep one time. In silent mode, the siren will not sound even if alarm is triggered. DISARM will quit from silent mode. Press for 3 seconds, Tracker will send SOS alarm to authorized phone numbers. Siren won't beep. Press for 0.5 second in arm state, siren will keep beep for 10 seconds,
press disarm key to quit
*If prefer to use APP and web server for set gps device , You can ignore the following instructions
11 SMS Functions
The device defaults to working in GPRS mode and SMS mode at the same time. If you only use SMS mode to manage the device, it is recommended to turn off GPRS by referring to the command on 11.23 to save power and GPRS data . Attention When reading this user manual, you will notice that we have used "+" and "space"between some words;"+" between two words means they should be written together as one word and "space" between two words means you should leave one character space between two words.
11.1 Changing Password
SMS command: password+oldpassword+space+new password, Tracker response: password OK . The default password is 123456,please changed password in the first time use it.
11.2 Authorization
Setup SMS command: admin+password+space+mobile phone number , Tracker response: admin ok Cancel SMS command: noadmin+password+space+authorized number Tracker response: noadmin ok Call the tracker 10 times in succession, the number will be authorize automatically as the first number and tracker response "add master ok" Up to 5 numbers can be authorized. Alarm information can only be received if authorized cell phone No. is set
11.3 Single Positioning
SMS Commandposition+password it will reply a SMS with a location reportClick the link to check the tracker's location on the map, Make a call to the tracker and it will automatically hang up and reply a SMS with positioning. If there aren't any authorized numbers set-up, it will reply all calls with a location report; if there are authorized numbers set-up, then it will not respond when an unauthorized number calls it
8
11.4 Positioning Strategy
11.4.1 Working mode Real time trackingonline+passwordgsm signal always online, the location can be queried at any time, and whether the device is stationary or moving, the location will be reported at set intervals. Smart modesleep+passwordThe tracker sleeps when it is stationary (phone calls, SMS, and alarms can trigger the tracker to go online. After SOS, door opening alarms, and illegal ignition alarms are triggered, the device will be online in real time until the alarm is lifted). It wakes up when it is in motion. Whether it is stationary or moving, the device will follow the set track interval time as accord to the location. 11.4.2 Setting Positioning Time Interval SMS Commandfix+020s+002h+005n+password, tracker will report at 20 seconds interval when the device is moving and update a position at 2 hours interval when motionless, and only 5 times are updated, 005n means 5 times, ***n means unlimited times. Cancel the setting: nofix+passwordTracker response: nofix ok
11.5 Remote Immobilizing
Delayed immobilizing Command: stop+password. When the current speed of the vehicle is greater than 20km/h, the command will not be executed immediately. It will be executed only after the vehicle speed is less than 20Km/h. Immobilizing immediately Command: quickstop+password, no matter whether the vehicle speed is greater than 20km/h, the command will be executed immediately. Remote fuel resume Command: resume+password, restore fuel and power supply.
11.6 Arming / Disarming
Armingarm+passwordResponseTracker is activatedthe vehicle terminal enters the armed state. If the vehicle is in the ignition state(Represents ths key not pulled),it cannot enter the armed state, and then reply "set up fail! pls turn off ACC". Silent Armingsilent+passwordRespondSilent ok!the terminal enters the silent arming state. After the alarm is triggered, the siren does not sound, but an alarm text message will be sent to the authorized number. Disarmingdisarm+passwordTracker responseTracker is deactivatedthe vehicle terminal will be deactivated, and these alarms won't be triggered any more.
11.7 Alarm function in arming state
11.7.1 Door Opening Alarm When the door is opened in arming state, the vehicle terminal will send SMS notification "Door alarm+latitude & longitude" to authorized numbers. The siren will beep for 20 seconds, and if the door is still open, then the siren will beep for another 20 seconds with 20 seconds pause, disarming to quit the alarm.
9
11.7.2 ACC Alarm Tracker will send "ACC alarm + latitude / longitude" to authorized numbers if the ignition of the vehicle has been switched "ON" (Key is rotated to "ACC ON" position ) or start the vehicle directly when tracker works in arming state. The siren will beep for 20 seconds, and if the ignition is still on, then the siren will beep for another 20 seconds with 20 seconds pause, disarming to quite the alarm. 11.7.3 Shock alarm The vehicle moves and shock when it in arming state and tracker will send "Sensor alarm + latitude / longitude" to authorized numbers, and only send once in 3 minutes. Siren will beep for 5 seconds for the first trigger and second trigger, and then beep 10 seconds for another trigger , disarming to quit the alarm There are three different levels for Vibration alarm, the defaults is level 2, SMS command: sensitivity+password+space+2
11.8 Alarms
11.8.1 Low battery alarm This feature is activated by default, when the battery voltage is close to 3.55V, tracker will send mess age "low battery + latitude & longitude" for 2 times at 15 minutes interval. SMS command to deactivate: lowbattery+password+space+off Tracker response: lowbattery off ok Example: lowbattery123456 off SMS command to activate: lowbattery+password+space+on Tracker response: lowbattery on ok Example: lowbattery123456 on 11.8.2 External power disconnection alarm This feature activate by default. Tracker will send "Power alarm+latitude& longitude" when external power disconnected. SMS command to deactivate: extpower +password+space+off Tracker response: extpower off ok Example: expower123456 off SMS command to activate: extpower +password+space+on Tracker response: extpower on ok Example: expower123456 on 11.8.3 SOS alarm
Press SOS button for 3 seconds(For model B/D, press key on the remote control), the tracker
will trigger SOS alarm 11.8.4 Movement alarm SMS command: move+password+space+ radius , Tracker response: move ok Cancel the setting: nomove+password , Tracker response: nomove ok Draw a circle with the current position of the device as the center, Once the device exceeds the radius, the movement alarm will be triggered. 11.8.5 Over speed alarm SMS commandspeed+password+space+ speed threshold , Tracker response: speed ok Cancel : nospeed+password, Tracker response: nospeed ok
10
When the speed exceeds the set speed threshold, an overspeed alarm will be triggered 11.8.6 Fuel alarm When the vehicle's fuel consumption exceeds the normal standard while the vehicle is running, or the re is fuel leakage or fuel stealing when the vehicle is stopped, tracker will send "oil: ××%+latitude & longitude" to the authorized numbers. The siren will beep for 20 seconds. SMS command to stop the notification: nooil+password For reasons such as different fuel tank heights and specifications of fuel sensor, tracker needs to set the proper height to zero and full values in order to read the correct percentage value. Calibrate 0% when the fuel tank is empty: SMS command: oilzero+password Tracker response: oilzero ok! Example: oilzero123456 Calibrate 100% after fill the fuel tank 100%: SMS command: oilfull+password Tracker response: oilfull ok! Example: oilfull123456
11.9 Configure times of alarm
The times of SOS, power, oil, door, ACC alarm sending can be set. SMS command: xtime+password+times value Response: xtime ok Send once by default.
11.10 Temperature alarm(Option)
The available temperature range is from -40 to 80. Send SMS command "temperature+password+space+the lowest temperature( the number should be 2 digits), the highest temperature ( the number should be 2 digits)"to the tracker, it will reply "temperature ok" .When the temperature is beyond the limited range, the tracker will send SMS alarm to the authorized numbers. Deactivate temperature alerts notemperature+password , Tracker response: notemperature OK
11.11 WiFi hotspot (For C/D model)
This function is deactivated by default. When the hotspot is turned on, user's other devices can use th e wifi name and password to connect to the Internet. activate: hotspot+password+space+on, Tracker Response: wifi name and password deactivate: hotspot+password+space+off, Tracker Response: hotspot off ok Check WiFi hotspotscheckhotspot+passwordTracker Responsewifi name and password Modify WiFi hotspot password SMS command: hotspotpwd+password+space+hotspot new password,Tracker Responsehotspotpwd ok
11.12 Listen
The default mode is Track mode, dial the device, reply position SMS command: listen+password, switch to Listen mode, dial the device, enter call
11
SMS command: tracker+password, restore to Track mode
11.13 ACC ON/OFF Alert
This function is OFF by default.
SMS command to activateACC+passwordTracker ResponseACC ok SMS command to deactivatenoACC+passwordTracker responsenoACC ok
11.14 SIM Card Balance Enquiry
First way: SMS command: balance+password+space+phone number of operator +space+code The tracker will forward the received text message from the operator to the sender of the command
Second way: SMS commandforward+password+space+phone number of operator When the network operator sends a text message requiring recharge, the tracker will forward it to the authorized number
11.15 Check Status
SMS command: check+password, Response: Power, Battery %, GPS signal, GSM signal, GPRS, APN, UP, IP, Port, Temperature, Humidity etc
11.16 Check IMEI
SMS command: imei+password Tracker response: xxxxxxxxxxxxxxx (A 15 digits IMEI of your device) Example: imei123456
11.17 Time zone setting
Tracker works in the local time zone by default. If you find that the time zone is incorrect, you can configure the time zone SMS command: time+space+zone+password+space+time zone value Tracker responds: time ok Example: time zone123456 8
11.18 Reset Hardware
SMS Command: reset+password Tracker Response: reset ok Example: reset123456
12
11.19 APN Setting
SMS command: APN+password+space+local APN ,Tracker response: APN OK Settings are only required to use the APP and web version platform.
11.20 Configure user name and password of GPRS
SMS command: up+password+space+user+space+password Tracker response: up ok Settings are only required to use the APP and web version platform
11.21 Configure Server IP/DNS
SMS command: adminip+password+space+IP/DNS domain name+space+port,Tracker response: dns success! No setup required to use baanooliot.com
11.22 TCP / UDP switch
SMS command: tcp+password, Tracker response: tcp ok SMS command: udp+password, Tracker response: udp ok No setup required to use baanooliot.com
11.23 SMS Mode
SMS command: SMS+passwordTracker response: sms ok The tracker turns on GPRS by default. If you prefer SMS and phone calls to manage the tracker, it is recommended to use this command to turn off GPRS.
11.24 GPRS Mode
SMS commandgprs+passwordTracker response: gprs ok
11.25 Initialization
SMS command: begin+password Tracker response: begin ok The tracker returns to default factory settings.
12 Package contents
No.
Photo
Name
Specifications
Applicable model
1
Harness
14PIN
Standard
2
Microphone
Length with 1.5 meters Standard
3
Relay
12V/40A or 24V/40A Standard
13
4
Siren
12V/24V
Optional
5
Fuel Sensor
Optional
6
Remote control
For D model
7
Temperature and Humidity sensor
Optional
8
Wifi Camera
Optional for C/D model
13 Cautions
Please be sure to follow when using: 1. Keep the tracker used in a dry environment. The humid environment can easily damage internal ci rcuits. 2. Please do not put it in a dusty environment. 3. Do not put the tracker in overheated or overcooled places. 4. Handle carefully. Don't vibrate or shake it violently. 5. Please clean with a dry cloth, do not use chemicals and detergents. 6. Please do not paint the device; this may lead to internal circuit failure. 7. Please read the user manual carefully before installation and operation, and understand voltage ran ge. Otherwise, it won't work properly or damage the tracker.
14 Troubleshooting
Faults Fail to turn on
No GSM signal
No GPS signal No response for SMS command
Solution
1. Please check if the power wiring is correct?
1. Check whether the SIM card is put in place. 2. Whether the SIM card is a GSM network SIM card. 3. Don't turn on the PIN code. 4. Call forwarding cannot be opened. The device needs to be in an unobstructed position to ensure that it can receive GPS signals normally. 1. No credit on SIM card. 2. The password is incorrect or the format of the SMS command
is incorrect.
14
1. Did you have set up the authorized phone number? No response for a call/No 2. If authorized number exists, did you make the call from an alarm notification message authorized phone number?
3. The format of the phone number is incorrect.
Fail to stop engine
1. Please check whether the engine stop wiring connected correctly?
Remote control cannot be used
Turn off tracker, and turn it on to program the remote control again.
15
WPS 文字
Related Documents
BAANOOL 303FG GPS Tracker User Manual Comprehensive user manual for the BAANOOL 303FG GPS Tracker, covering specifications, hardware description, installation, device status, mobile app, web version, SMS functions, and troubleshooting.
BAANOOL GPS Tracker Model 407 User Manual Comprehensive user manual for the BAANOOL GPS Tracker Model 407, covering specifications, installation, hardware description, mobile app usage, web version, positioning strategies, SMS functions, troubleshooting, and cautions.
BAANOOL 311 GPS Tracker User Manual Comprehensive user manual for the BAANOOL 311 GPS Tracker. Covers installation, hardware, specifications, device status, mobile app, web platform, SMS commands, alarms, accessories, and troubleshooting.
GSM/GPRS/GPS Portable Tracker User Manual User manual for the GSM/GPRS/GPS Portable Tracker, detailing its features, specifications, setup, functions, and troubleshooting.
Portable GPS Tracker User Manual - BAANOOL 408 Comprehensive user manual for the BAANOOL Portable GPS Tracker (Model 408/408B). Covers specifications, hardware details, installation, app/web/SMS operation, positioning strategies, alarms, and troubleshooting. Learn how to set up and manage your device for optimal tracking and security.
Portable GPS Tracker User Manual User manual for the Portable GPS Tracker, detailing its specifications, hardware description, installation, operation via mobile app and web platform, SMS functions, and troubleshooting.
GSM/GPRS/GPS Tracker User Manual - BAANOOL Comprehensive user manual for the BAANOOL GSM/GPRS/GPS Tracker, detailing installation, setup, features, functions, and troubleshooting for vehicle tracking and security.
GPS Tracker User Manual - BAANOOL Model 403 User manual for the BAANOOL GPS Tracker (Model 403). Provides detailed instructions on installation, SIM card setup, device operation, GPRS configuration, mobile app usage, web platform access, and various functional details for tracking and security.
