SpeaKa Professional SP-MM-980 Dual Monitor Arm

Important Safety Information

IMPORTANT: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty.

Instructions of Safety and Warnings:

• Make sure that the mounting surface is strong enough to handle the mounted product and equipment.
• [Warning] Do not exceed the maximum listed weight capacity.
• Always use an assistant or a mechanical lifting device to safely lift and position heavy products.
• Tighten screws firmly, but do not over tighten. Over tightening can cause product damage that greatly reduces the holding power.
• Keep a clear area and distance from moving parts when using the product.
• Use only as intended. Never stand, hang, or climb on the product.
• This product is intended for indoor use only.
• Any attempts to reconstruct the construction are not allowed.
• This product may contain small items that could be a choking hazard if swallowed. Keep children away unless they are intended users and have fully reviewed and understood all instructions and manuals.
• Check that the product is secure and safe to use at regular intervals (at least every three months).

Should you ever have any questions or feel you require help, please contact your place of purchase for assistance.

Product Specifications

• VESA Mount Support: 75 x 75 mm and 100 x 100 mm
• Maximum Reach: 124.46 cm (49 inches)
• Weight Capacity: 2-20 kg per arm (x2)
• Monitor Compatibility: Suitable for Flat/Curved monitors

Parts List

• Part A (x1): Desk Clamp Base
• Part B (x1): Lower Pole Section
• Part C (x1): Upper Pole Section
• Part D (x1): Lower Arm Segment
• Part E (x1): Upper Arm Segment
• Part F (x1): VESA Mounting Plate
• Part G (x1): Pole Clamp
• Part H (x1): Tension Adjustment Knob
• Part I (x1): Desk Clamp Screw (long)
• Part J (x1): Pole Locking Screw (short)
• Part K (x2): M4x12 screws
• Part L (x2): M5x12 screws
• Part M (x1): M8x25 screws
• Part N (x1): M8x50 screws
• Part O (x1): M8x130 screws
• Part P (x1): Allen Key (4mm)
• Part Q (x1): Allen Key (6mm)
• Part M-A (x4): M4x10 screws (for monitor attachment)
• Part M-B (x4): M5x12 screws (for monitor attachment)
• Part M-C (x4): M6x14 screws (for monitor attachment)

Assembly Instructions

Step 1: Desk Mount Setup

• 1a. Attach the Desk Clamp Base (A) to the edge of your desk (thickness 12-50mm) using the Desk Clamp Screw (I).
• 1b. Insert the Lower Pole Section (B) into the Desk Clamp Base (A). Secure it using the Pole Locking Screw (J). Attach the Upper Pole Section (C) to the Lower Pole Section (B) and secure it with the Pole Clamp (G) and Pole Locking Screw (J).

Step 2: Arm Assembly to Pole

Attach the main arm assembly (Lower Arm Segment D and Upper Arm Segment E) onto the pole structure (B/C). Secure it using the Pole Clamp (G) and Pole Locking Screw (J).

Step 3: Tension Adjustment Knob Installation

Install the Tension Adjustment Knob (H) onto the Lower Arm Segment (D).

Step 4: VESA Plate Attachment to Arm

Attach the VESA Mounting Plate (F) to the end of the Upper Arm Segment (E) using the M4x12 screws (K).

Step 5: Monitor Attachment to VESA Plate

Position your monitor onto the VESA Mounting Plate (F). Secure the monitor using the appropriate screws: M4x10 (M-A), M5x12 (M-B), or M6x14 (M-C), depending on your monitor's VESA mounting holes. Ensure the monitor is oriented correctly, noting any "TOP" indicators.

Step 6: Arm Joint Securing

Use the M8x25 (M), M8x50 (N), or M8x130 (O) screws to secure the arm joints as needed for stability and desired movement range.

Step 7: Final Check

Ensure all connections are secure and the monitor is stable.

Arm Balancing and Tension Adjustment

To properly balance the arm with the monitor mounted, adjust the spring tension using the supplied Allen Key (P or Q).

Procedure:

1. Position and firmly hold the arm horizontally. Seek assistance if needed.
2. If the arm drops: Turn the adjustment screw (H) counter-clockwise until it stays in a horizontal position.
3. If the arm rises: Turn the adjustment screw (H) clockwise until it stays in a horizontal position.

CAUTION: To avoid damage to the monitor or mount, always keep the arm in a horizontal position while making adjustments. Seek assistance if required.

CAUTION: Do not over-tighten the screws.

Cable Management

Route your monitor cables (power and video) through the designated channels within the arm segments to keep your workspace tidy and prevent cable strain.