POS Mounting Solution

Important Safety and Warning Instructions

IMPORTANT: Failure to read, understand, and follow all instructions can result in serious personal injury, equipment damage, or voiding of the factory warranty.

General Safety Precautions:

• Ensure the mounting surface is strong enough to support the mounted product and equipment.
• DO NOT EXCEED THE MAXIMUM LISTED WEIGHT CAPACITY.
• Always use an assistant or a mechanical lifting device for safe lifting and positioning of heavy products.
• Tighten screws firmly, but do not over-tighten. Over-tightening can cause product damage and significantly reduce holding power.
• Maintain a clear area and distance from moving parts when using the product.
• Use only as intended. Never stand, hang, or climb on the product.
• This product is intended for indoor use only.
• Reconstruction of the product's construction is not permitted.
• This product may contain small items that could be a choking hazard if swallowed. Keep children away unless the product is intended for their use and all instructions and manuals are fully reviewed and understood by them.
• Check that the product is secure and safe to use at regular intervals (at least every three months).

Assistance:

Should you have any questions or require assistance, please contact your place of purchase.

Product Specifications

This POS mounting solution supports monitors with VESA compatibility (75x75mm and 100x100mm).

Maximum supported screen size: 32 inches.

Maximum weight capacity: 9 kg (19.8 lbs).

Includes holders for terminal, printer, and scanner.

Features adjustable cable clips.

Included Parts

• Part A (x1): Base Plate
• Part B (x1): Pole
• Part C (x1): Pole Clamp
• Part D (x1): Monitor Arm
• Part E (x1): Arm Clamp
• Part F (x1): VESA Plate
• Part G (x1): Base Screw (M-A) - For through-hole mounting
• Part H (x1): Pole Screw (M-B) - For desktop mounting and attaching arm to pole
• Part I (x1): Arm Clamp Screw (M-C) - For attaching arm clamp to monitor arm
• Part J (x1): VESA Plate Screw (M5x6) - For attaching VESA plate to arm clamp
• Part K (x2): Cable Clips
• Part L (x3): Washers
• Part M (x2): Screws for Terminal Holder
• Part N (x1): Printer Holder
• Part O (x4): Screws for Printer Holder
• Part P (x1): Scanner Holder
• Part Q (x1): Allen Key (4mm)
• Part R (x1): Allen Key (6mm)
• Monitor Mounting Screws: Various sizes (e.g., M4x12, M5x12) for attaching monitor to VESA plate.

Assembly Instructions

Step 1: Prepare Mounting Surface

Two mounting options are available:

• Option 1 (Through-Hole): Use a surface with a hole (Ø 10-60mm). Attach Base Plate (A) using Base Screw (G) and Washers (L).
• Option 2 (Desktop): Use a desktop surface (10-40mm thick). Attach Base Plate (A) using Pole Screw (H) and Washers (L).

Step 2: Attach Pole to Base

Insert Pole (B) into Base Plate (A). Secure using the appropriate screw from Step 1 (G for through-hole, H for desktop).

Step 3: Attach Arm to Pole

Slide Pole Clamp (C) onto Pole (B). Attach Monitor Arm (D) to Pole Clamp (C) using Pole Screw (H).

Step 4: Attach VESA Plate

Attach Arm Clamp (E) to Monitor Arm (D) using Arm Clamp Screw (I). Attach VESA Plate (F) to Arm Clamp (E) using VESA Plate Screw (J).

Step 5: Mount Monitor

Attach the monitor to the VESA Plate (F) using the provided monitor mounting screws (M-A, M-B, M-C). Ensure correct screw length is used to avoid damage. [Note: Select screws that fit snugly without being too long or too short].

Step 6: Attach Holders and Cable Management

Attach the Terminal Holder using screws (M).

Attach the Printer Holder (N) using screws (O).

Attach the Scanner Holder (P).

Use Cable Clips (K) for cable management, adjusting them as needed. The cable clips can be adjusted by demand [adjustment-symbol].

Step 7: Adjustments

Fine-tune monitor tilt by loosening and tightening screws on the arm [adjustment-symbol].

Adjust the width of the arm according to the connected device.

The cable clip (K) can be adjusted as needed.