Bodet BTX8020 SET Scoreboard

1. Electrical and Mechanical Safety Standards

It is recommended to read this manual carefully before installing the product. Failure to observe these instructions may cause irreversible damage and invalidate the warranty. Bodet shall not be responsible for any damage arising due to non-observance of these instructions.

Identification of Pictograms

Installing the Product

[warning symbol] This equipment must be fitted and maintained by a qualified person.

Electrical Installation

The scoreboard must be powered through the building's electrical installation. It is designed for Category II overvoltage with a maximum peak voltage of 2500V. If necessary, provide mains power supply protection compliant with CEI 61643. The electrical installation must comply with the rules laid down in the standards in force in the country where the product is used, including the IEC 364 standard. A differential circuit breaker with a maximum rating of 30mA per phase-neutral and 16A maximum, rapidly accessible upstream from each power-supply line, is required for permanent power supply. This circuit breaker provides power supply protection and disconnecting, and must be switched off during maintenance. Conductors on the same circuit must be attached to each other close to the terminal block to avoid reduced isolation should one of the terminals become loose. The equipment should not be powered up until it has been mounted to the wall, and the scoreboard must be closed.

2. Installation

2.1 Checking the Equipment

BTX8020 SET (Ref. 916091):

• Scoreboard BTX8020 SET.
• Installation and operating instructions.

BTX8020 SET Scoreapp (Ref. 916092):

• Scoreboard BTX8020 SET.
• Installation and operating instructions.
• Box Scoreapp (installed inside the scoreboard BTX8020 SET).

2.2 Presentation

The scoreboard features a display per sport with 5 red digits of 20 cm per team.

• Tennis and Padel: Displays sets, games, and points.
• Badminton and Squash: Displays sets and points.
• Volleyball and Table Tennis: Displays the number of sets won and points in the current set.

[service indicator symbol] A service indicator is represented by a red dot (Ø36 mm) per team or player.

Stickers labeled 'A' and 'B' are provided for team or player identification.

CAUTION: The maximum distance for communication via HF control between the keyboard and the scoreboard is 100 meters in an open field.

2.3 Mechanical Installation

Wall Mounting

Attach the scoreboard to the wall using 4 screws (Ø8 mm) and suitable wall plugs (not supplied). Utilize the 4 keyhole slots located on the rear of the BTX8020 SET scoreboard.

Post Mounting (Ref. 915170)

1. Pour two blocks of concrete for the two posts using the provided jigs (915196). The dimensions for each concrete block are L = 75 cm, I = 75 cm, P = 75 cm.
2. Seal 8 anchor bolts (915178) in each block (4 anchors per block) and then tighten the nuts. Ensure careful checking of the spacing and height of the anchor bolts.
3. Attach the panel to the 2 posts using the 4 clamps and the threaded rods (B).

Diagram Descriptions for Mechanical Installation:

• Wall Mounting Dimensions: The scoreboard unit has overall dimensions of approximately 2000mm (width) x 620mm (height) x 560mm (depth), with a main display width of 1560mm and a side panel width of 122mm.
• Post Mounting Dimensions: The upright posts are approximately 3365mm in height. The base of the post is approximately 220mm wide, with anchor bolt spacing of 200mm. The post itself is approximately 100mm wide.
• Anchor Bolt Assembly: Consists of a bent anchor bolt M16, a flat washer M16, and a nut HU M16.
• Post Base: Features a rigid insulating PVC tube (Ø20) and plate edge clips.
• Panel Attachment: The panel is attached to the posts via clamps and threaded rods. The panel dimensions are approximately 1560mm (length) x 125mm (height) x 113mm (width). It includes a cable cover and flange.

2.4 Electrical Connection

Connect the scoreboard's power supply to a mains outlet.

[power symbol] Connect to mains outlet.

3. Commissioning

3.1 BTX8020 SET (Ref. 916 091)

The Scorepad keyboard is not included with reference 916 091 and must be ordered separately.

HF Installation

From the Scorepad keyboard:

1. On the Scorepad homepage, click the menu icon [menu icon].
2. Click 'Technician menu' (code: 4934).
3. Select the 'Communication' menu.
4. Click one of the previously created configurations.
5. Click 'Communication type'.
6. Select 'HF'.

The link between the Scorepad and the BTX8020 SET scoreboard is established via an 868MHz HF modem. For this mode, the installation number and the channel number must be configured.

Configuration Example:

• Scoreboard: BTX 8020 SET
• No. Installation: 1
• No. Scoreboard: 1
• No. Channel: 1

Wired Installation

From the Scorepad keyboard:

1. On the Scorepad homepage, click the menu icon [menu icon].
2. Click 'Technician menu' (code: 4934).
3. Select the 'Communication' menu.
4. Click one of the previously created configurations.
5. Click 'Communication type'.
6. Select 'Wired'.

Connection Details:

• Power: 230VAC
• Required Cable: Ref. 916014 (keyboard/connection box cable + DIN wall outlet)

Connecting the Scorepad to the BTX8020 SET scoreboard:

1. Unscrew the 4 cross-headed screws on the right side of the BTX8020 SET to remove the side panel.
2. Slide the glass to the right. [warning symbol] Do not press on the glass as this may damage the LEDs.
3. Unscrew the middle LED module on the second line.
4. Connect the keyboard cable to the MDM terminal block (RT+: white / Brown: RT-).
5. Reassemble the glass and side panel by carrying out steps 1 and 2 in reverse order.

3.2 BTX8020 SET Scoreapp (Ref. 916 092)

The Scoreapp box is factory installed and connected inside the BTX8020 SET scoreboard. No additional installation action is required after connecting the mains power supply to the BTX8020 SET scoreboard (refer to paragraph 2.4 Electrical Connection).

3.3 Dip-Switch Settings

Dip-switch settings are only necessary if you intend to use two (or more) BTX8020 SET scoreboards simultaneously. Refer to the "Bodet scoreboard installation guide" for specific DIP-switch settings for multi-scoreboard installations and for testing the display of the scoreboard(s) and the Scorepad keyboard.

4. Use

4.1 BTX8020 SET (Ref. 916 091)

Use the Scorepad keyboard for operation. Download the relevant sport's manual from the following link:

https://www.bodet-sport.com/support/documents-database/scorepad.html

4.2 BTX8020 SET Scoreapp (Ref. 916 092)

Use the Scoreapp application for operation. Download the Scoreapp manual from the following link:

https://www.bodet-sport.com/support/scoreapp.html

5. Technical Features