ROPOX 4SingleElectric
User Manual & Mounting Instructions
This document provides comprehensive instructions for the ROPOX 4SingleElectric height-adjustable table.
1. Introduction
The 4SingleElectric is a multi-function table, electrically adjustable to suit seated or standing activities. Its unique design allows for a variety of applications, making it ideal for wheelchair users.
⚠️ This document must ALWAYS accompany the product and be read by and available to users.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless supervised by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.
All users must follow these instructions. It is crucial that the instructions are read and understood prior to operation.
Correct use, operation, and inspection are decisive factors for efficient and safe performance.
⚠️ This product is electrically adjustable in height, posing a risk of trapping. Operation must be made or supervised by an adult who understands the safety precautions.
The frame is provided with an infrared remote control, which must always be kept out of reach of children.
2. Conformity with EU-Directives and UK-Directives
This product has CE-marking and meets the safety requirements of the Machinery Directives. If the table frame is assembled with other electrical components, it will be considered a new unit and require a risk assessment for CE-marking.
This product has UKCA-marking in accordance with UK SI 2008 No. 1597 - The Supply of Machinery (Safety) Regulations 2008, and its amendments.
3. Application
The 4SingleElectric is designed to provide optimum working height. It is an activity table and should not be used as a lifting table or person lifter.
The product must be used indoors, under normal room temperatures and humidity. It is not designed for use in damp rooms.
The control unit has IP32/II protection and must be installed in accordance with low voltage directives or corresponding national/international legislation.
4. Technical Data
| Product Name | 4SingleElectric |
|---|---|
| Item Number | Set of legs, Electric |
| Height 55-85 cm / 21.6 – 33.4 in (H1) | 50-41120 |
| Height 65-95 cm / 25.6 – 37.4 in (H2) | 50-41220 |
| Front fascias for frame L = xxx cm (60-300cm increments of 1cm / 23.6-118.1in increments of 0.4in) | 50-43xxx |
| Side fascias for frame W = xxx cm (60-200cm increments of 1cm / 23.6 - 78.7in increments of 0.4in) | 50-45xxx |
| Options | Wheels: Increase table height by 6.5cm/2.5in; Flexible safety strip |
| Material | Welded steel tubes St. 37 and various plastic components |
| Surface treatment | Blue chromate, powder coating: Standard CWS 81283 RAL 7021 mat |
| Power supply | 220-230V~/ 50-60Hz, 5.0A |
| Standby primary | 0.3W |
| Control voltage | 24VDC |
| Duty circle | Max. 10% conform to 2 min. active / 18 min. pause |
| Max. load of frame | 150 kg / 330 lb evenly distributed |
| Speed/lifting time | Approx. 32 mm/sec. (approx. 10sec.) |
| Increased load of frame (option) | 250 kg / 551 lb evenly distributed |
| Speed/lifting time (increased load) | Approx. 12 mm/sec. (approx. 25sec.) |
| Temperature | 5-45°C |
| Air humidity | 5-85% (non-condensing) |
| Producer | Ropox A/S, DK-4700 Naestved, Tel.: +45 55 75 05 00, e-mail: info@ropox.dk - www.ropox.com |
5. Schematic Diagram of Frame
All electrical connections to the control unit must be flexible to ensure the table moves freely within its adjustment range.
Frame Dimensions:
- Width: 60-200cm / 23.6-78.7in (Frame width is 0.4cm less than table top width).
- Length: For table top length 60-300cm / 23.6-118.1in (Frame length is 0.4cm/0.2in less than table top length).
- Height: 55-85cm (H1) / 21.6-33.4in; 65-95cm (H2) / 25.6-37.4in. Height with wheels adds 6.5cm/2.5in.
Table Sizes:
- Without middle support: Length 60cm-300cm / 23.6-118.1in; Width 60cm-120cm / 23.6-47.2in.
- With middle support: Length 60cm-300cm / 23.6-118.1in; Width 121cm-200cm / 47.6-78.7in.
Illustration showing the frame structure with dimensions for length, width, and height, including notes on frame width and length relative to tabletop dimensions. Also shows configurations with and without a middle support, and the addition of wheels.
6. Mounting Instructions & Description
Mounting must always be carried out by competent personnel. Prior to mounting, check that all parts have been provided (see Section 7).
6.1 Assembly of Frame
- 6.1.1 Mount hexagonal shaft and motor cable: Illustration shows hexagonal shaft and motor cable being installed.
- 6.1.2 Mount motor on side fascia: Illustration shows motor mounted on side fascia, with the profile cut away from the table top.
- 6.1.3 Mount the spring for retention of motor plug: Illustration shows the spring being fitted to secure the motor plug.
- 6.1.4 Check and adjust leg height: Illustration shows checking that all four legs are identical in height. Adjustment is made on the hexagonal shaft using the provided open-end wrench. Side fascias are placed on a plane surface and legs are mounted. Refer to labels on legs.
- 6.1.5 Mount front fascias: Illustration shows mounting the two front fascias. Push side and front fascias firmly against the leg before retightening. Tighten bolts securely with the provided wrench.
- 6.1.6 Position angle plate for control unit: Illustration shows positioning the angle plate for the control unit on the front fascia and fastening it.
- 6.1.7 Attach control unit: Illustration shows attaching the control unit to the angle plate and fastening it.
- 6.1.8 Place frame on tabletop: Illustration shows placing the frame on the tabletop and pushing cover plates between legs and tabletop. Centre the frame.
- 6.1.9 Fasten tabletop: Illustration shows fastening the tabletop with screws through the fascia holes.
- 6.1.10 Mounting of fixed control switch: Illustration shows pulling the cable through the front fascia and inserting it into the control unit.
- 6.1.11 Connection to control unit: Diagram illustrates connections: Motor cable M1, Motor cable M2, mains cable, adapter cable for safety strip, and cable for control switch to the control unit.
6.2 Mounting of Safety Strip
Ropox recommends the use of safety strips on electrically adjustable frames.
⚠️ Be careful not to damage the safety strip during transportation or mounting. If the safety strip is bent or twisted, it may not function correctly.
The surface for adhesion must be clean and dry for optimal adhesion.
- 6.2.1 Attach safety strip: Illustration shows pushing the safety strip through all four legs and fitting it to the underside of the fascia using the provided double-adhesive tape. Remove protection paper and press firmly. Observe minimum bending radius (2cm inside). Refer to separate instructions for mounting and handling the safety strip.
6.3 Performance Test
All functions must be tested after mounting and before first use. A performance test should be carried out at least annually by competent personnel.
Testing prior to switching on power:
- Check that mounting instructions have been observed.
- Check that all bolts are tightened.
- Check that all cables are connected correctly and plugs are home.
- Ensure no load is on the table.
- Ensure no objects obstruct free movement within the height adjustment range.
Start-up Procedure:
- Connect the net cable and turn on power.
- Connect motor cables to M1 and M2.
- Connect the control switch to HS.
- Press DOWN on the control switch to move the frame to the bottom position. Check for even, smooth movement and that hose connections are not squeezed. The frame is now reset.
- Press UP on the control switch to move the frame to the top position. Check for even, smooth movement and that hose connections are not squeezed.
Safety Strip Test (if fitted): Press the DOWN button, allowing the table to move 2-5cm/0.8-1.9in downward while activating the safety strip. The table must stop downward movement, move 1-2cm/0.4-0.8in upward, and then stop.
The table is ready for use once all tests are successfully completed.
7. List of Components
The following components are included:
- Set of legs H1 (Item number 50-41120): Illustration of four legs. (1 set)
- Set of legs H2 (Item number 50-41220): Illustration of four legs. (1 set)
- Front fascias for L=xxx cm (Item number 50-43xxx): Illustration of two front fascia profiles. (1 set)
- Side fascias for W=xxx cm (Item number 50-45xxx): Illustration of two side fascia profiles. (1 set)
- Control unit (26.5x10.5x3.7cm, 50-41500, 230VAC, incl. mains cable 300cm/118.1in): Illustration of the control unit box. (1 pc.)
- Contained in control unit:
- Control switch, small press pad (3x6cm, 30-67840): Illustration of a compact control panel. (1 pc.)
- Control switch, standard (Incl. 150cm/59in cable): Illustration of a standard control panel. (1 pc.)
- Adhesive plate (Item number 96000155): Illustration of a triangular adhesive plate. (5 pcs.)
- Strips black (Item number 96000165): Illustration of black strips. (5 pcs.)
- Angle plate for control unit (Item number 50*40000-039): Illustration of an angle bracket. (1 pc.)
- Motor (Item number 96000553): Illustration of an electric motor. (2 pcs.)
- Motor cable (Item number 96000573): Illustration of a motor cable. (2 pcs.)
- Adapter cable (Item number 96000557): Illustration of an adapter cable. (2 pcs.)
- Allen screw M8x16 (Item number 95010003): Illustration of an Allen screw. (16 pcs.)
- Screw Ø4.8x13, Torx (Item number 95091012): Illustration of a Torx screw. (6 pcs.)
- Screw Ø4.2x6.5 (Item number 95090806): Illustration of a screw. (2 pcs.)
- Spring (Item number 50-40000-040): Illustration of a spring. (2 pcs.)
8. Options
- Split cable for control switch (Item number 96000629): For use with more than one control switch. Illustration of a Y-shaped cable splitter. (1 pc.)
- Safety strip (Item number 30-69xxx): Illustration of a safety strip. (1 pc.)
- Brake wheels, grey (4 wheels) (Item number 50-41600): Increases table height by 6.5cm/2.6in. Illustration of four grey wheels. (1 set)
- Increased lifting power, set of legs H1 (Item number 50-41320): Max. load 250kg/551lb evenly distributed. Gear housing will be green and black. (To be ordered with main order). (1 set)
- Increased lifting power, set of legs H2 (Item number 50-41420): Max. load 250kg/551lb evenly distributed. Gear housing will be green and black. (To be ordered with main order). (1 set)
9. Safety in Use
- 4Single must only be used by persons who have read and understood these instructions.
- The infrared remote control must always be kept out of reach of children.
- As an electrically operated height-adjustable table, the use of a safety strip is recommended to prevent damage and accidents. Always ensure no persons, animals, or objects are under the table during use, even with a safety strip fitted.
- 4Single is an activity table and should not be used as a lifting table or person lifter.
- Always use the table in a manner that excludes the risk of damage to persons or property. The operator is responsible for avoiding damage or injury.
- Children or persons with reduced observation capability should only operate the table when supervised.
- In publicly accessible locations, operators must pay attention to present persons to prevent dangerous situations.
- Ensure free space above and below the table for height adjustment.
- Do not operate the table if it has defects or damage.
- Do not overload the table and ensure correct load distribution.
- Do not use the table in an explosive environment.
- When performing inspections, service, or repairs, always remove loads from the table.
- When installing power or water connections, observe national authority regulations.
- Modifications affecting operation or construction are not allowed.
- Installation, service, and repairs must be carried out by competent personnel.
- Failure to assemble according to these instructions may void the right to complain.
- Only use Ropox original spare parts. Using other spare parts may void the right to complain.
10. Cleaning/Maintenance
10.1 Cleaning of Frame
⚠️ WARNING: The frame must NOT be connected to mains voltage during cleaning. Do NOT flush electrical components with water.
Clean the frame with a wrung cloth using lukewarm water and a mild detergent. Do not use harsh chemicals, abrasives, grinding cloths, brushes, or sponges.
Dry the frame after cleaning.
10.2 Maintenance
Inspections, service, and repairs must be carried out by competent personnel.
The frame is maintenance-free, and moving parts are lubricated for life. For safety and reliability, inspection of the frame once a year is recommended:
- Check that all bolts are tightened.
- Check that the table moves freely and without problems from bottom to top position.
- Resetting of frame: Press the DOWN button to adjust the frame to the bottom position. Press the DOWN button again and hold for 5 seconds to reset the control unit.
- Check that the movement is smooth and even. Ensure the mains cable moves freely.
- Check that water connection hoses and draining hoses (if applicable) are tight and functional.
- Check that the cable to the hotplate (if applicable) is undamaged and moves freely.
- Check that all cables are correctly mounted and undamaged.
After each inspection, fill in the service schedule (See 10.3). Only use Ropox original spare parts.
10.3 Service Schedule, Operation and Maintenance
Sections for recording Service and Maintenance details, including Serial No., Date, Signature, and Remarks, are provided.
11. Trouble Shooting
11.1 The frame seems loose or unstable
- The screws assembling the frame may not be securely tightened. Tighten all screws as per mounting instructions.
11.2 The height of the frame cannot be adjusted (adjustment seems very difficult)
- Check mains voltage to the control unit and ensure power is switched on.
- Check cables and plug-in connections between the control unit and motors.
- Check cable and plug-in connection between the control unit and control switch.
- Check connection of cables for the safety strip to the control unit and safety strip. (If no safety strip is fitted, a short-circuit plug must be on the safety strip cable; see mounting instructions fig. 6.2.2).
- If a safety strip is fitted: Check that the safety strip has not been activated. Remove the short-circuit plug from the safety strip to the Y-cable of the control unit (see mounting instructions fig. 6.2.2). If the table works without the safety strip connected, the safety strip has been activated.
11.3 The frame does not move straight
- If the frame does not move straight, it must be reset (see Maintenance, Section 10.2).
- ⚠️ If there has been a power failure, the table must always be reset before use.
12. Complaints
For complaints, please refer to the General Terms of Sale and Delivery available on www.ropox.com.
ROPOX A/S
Ringstedgade 221
DK-4700 Naestved
Tel.: +45 55 75 05 00
Fax.: +45 55 75 05 50
E-mail: info@ropox.dk
www.ropox.com
mailto:info@ropox.dk
Ropox - World's leading disability friendly solutions
