ROPOX FlexiElectric Corner Mounting Instructions

1. Introduction

Any design, installation, and normal use must only be carried out if the FlexiElectric Manual is used in combination with these Mounting Instructions. All other information, including use and technical data, will be found in the FlexiElectric Manual.

Producer: Ropox A/S, DK-4700 Næstved, Tel.: +45 55 75 05 00, E-mail: info@ropox.dk, www.ropox.dk

Mounting Steps

1. Slide the first leg onto one of the aluminium profiles and pass the hexagonal shaft through the hole of the leg. Tighten the screws lightly.

   [Diagram: First leg being attached to an aluminium profile beam with a hexagonal shaft inserted.]

2. Slide the bracket into the aluminium profile. It MUST be placed over the leg. Tighten the screws lightly.

   [Diagram: Bracket being slid into the aluminium profile, positioned over the leg.]

3. Slide the nut of the motor fixture into the aluminium profile on the underside and guide the hexagonal shaft through the motor. Tighten the screws lightly.

   [Diagram: Motor fixture nut sliding into the underside of the profile, hexagonal shaft going into the motor.]

4. Place the motor beside the leg and tighten the screw lightly.

   [Diagram: Motor positioned next to the leg, screw being tightened.]

5. Slide the next leg into the aluminium profile. Tighten the screws lightly.

   [Diagram: Second leg being attached to the aluminium profile.]

6. Place the next bracket over the second leg. If extra brackets are required between the two shown, they must be mounted first. Tighten the screws lightly.

   [Diagram: Second bracket placed over the second leg.]

7. Slide the two nuts of the angular fitting into the aluminium profile. Tighten the screws lightly.

   [Diagram: Two nuts of an angular fitting sliding into the aluminium profile.]

8. Slide the nut of the angular gear casing into the aluminium profile. Ensure the gear is placed as illustrated. Place the hexagonal shaft in the gear casing. Tighten the screws lightly.

   [Diagram: Nut of angular gear casing sliding into profile, hexagonal shaft inserted into gear casing.]

9. Assemble the other side following the same procedure. Do not tighten screws until the whole frame is assembled. Place the leg.

   [Diagram: The second side of the frame being assembled, mirroring the first side.]

10. Place the bracket.

    [Diagram: Bracket being placed on the second side.]

11. Place the motor.

    [Diagram: Motor being placed on the second side.]

12. Place the leg.

    [Diagram: Leg being placed on the second side.]

13. Place the outermost bracket.

    [Diagram: Outermost bracket being placed.]

14. Assemble the two frames in the angular fitting. Ensure both hexagonal shafts are fully seated in the gear casing.

    [Diagram: Two frame sections being joined at the angular fitting, shafts inserted into gear casings.]

15. Place the aluminium profiles so that they are flush in the corner.

    [Diagram: Aluminium profiles aligned flush in the corner joint.]

16. Tighten the four screws of the angular fitting and one screw of the gear casing fitting.

    [Diagram: Screws on the angular fitting and gear casing fitting being tightened.]

17. Mount the assembly fitting on the two brackets in the corner of the frame. Move the legs from side to side until the brackets fit as illustrated. Tighten the two screws.

    [Diagram: Assembly fitting being mounted onto corner brackets, legs adjusted for fit.]

18. Tighten the two screws.

    [Diagram: Two screws being tightened on the assembly fitting.]

19. When all legs and brackets have been aligned and placed in the required position, tighten all screws!

    [Diagram: Final tightening of all screws on the assembled frame.]

20. If a support arm (bracket) is not level but points upwards, this can be rectified by mounting the included angle piece between the support arm and the aluminium profile.

    [Diagram: Illustration showing how to add an angle piece to level a support arm.]

Final Instructions

Before use, follow the instructions of the FlexiElectric User Manual!

Contact:

ROPOX A/S

Ringstedgade 221

DK-4700 Næstved

Tel.: +45 55 75 05 00

Fax: +45 55 75 05 50

E-mail: info@ropox.dk

www.ropox.dk

[Certifications: CE, UK CA]