Outsunny 845-425 Garden Shed Assembly Instructions

Product Information

Model Numbers: 845-425, 845-425V00, IN230600095V01_GL

This document provides assembly instructions for the Outsunny garden shed.

Assembly Preparation

Before beginning construction, please check local building codes regarding footings, location, and other requirements. Study and understand this owner's manual for important information and helpful tips for easier and more enjoyable assembly.

Assembly Instructions: Review all instructions and appropriate information before you begin. Ensure you follow the step sequence carefully for successful results.

Flooring Base Preparation

The site must be prepared so that the base of the shed is level all around, verified with a spirit level. The base can be constructed from treated timber or concrete to prevent moisture ingress. The shed is not designed to be built directly onto lawn; the ground may become muddy during rainy days.

If a concrete pad is made, it is important that it slopes towards the edges to prevent water ingress. Allow adequate time for any concrete or cement to dry before building the shed on top.

Bases can also be constructed from bricks, blocks, or mounted on a concrete pad. Bricks or blocks should be cemented onto firm, level concrete footings, and the shed frame drilled and screwed to the base.

Parts and Parts List

Before starting, separate and identify all parts and hardware to ensure you have all necessary components for your building. Refer to the Parts List for details.

Do not attempt to assemble the building if parts are missing, as a partially assembled building can be seriously damaged by light winds.

Tools Recommended

✂️, ?️, ?, ?, ?, ?️, ?, ?‍?‍?

Parts List

Safety First

Safety must be put in the No. 1 position:

1. Select a dry and calm day for your assembly. Teamwork (Two or more people) is required during assembly.
2. Wear safety gloves, eye protection, and long sleeves during assembly to prevent injury. Pay attention to the sharp edges of some parts.
3. Children and pets are not allowed on the construction site.
4. Never concentrate your total weight on the roof of the building. When using a step ladder, ensure it is safe.

Care & Maintenance

1. Keep the shed clean with a soft cloth, using water if necessary.
2. Keep the door tracks clear of dirt and other debris that prevent them from sliding easily.
3. Clean snow with necessary tools to ensure safe entry. Heavy snow may cause collapse; ensure safety before entering.
4. The shed is not made for living but for storing items.

Assembly Steps

1. Step 1: Connect part 2L and part 2R.
2. Step 2: Connect part 1L and part 1R to the frame from Step 1, using fastener F1.
3. Step 3: Connect part 3L and part 3R to the frame using fastener F1.
4. Step 4: Assemble the floor frame using part 5 and fastener F1. Ensure the floor frame is square and level.
5. Step 5: Verify diagonal measurements are equal for a square frame. The floor frame must be both square and level for proper hole alignment.
6. Step 6: Attach part P1 to the floor frame using fasteners F1 and S3.
7. Step 7: Attach part P4 to the floor frame using fasteners S3 and F2.
8. Step 8: Attach part P3 to the floor frame using fasteners F1 and S3.
9. Step 9: Attach part P4 to the frame using fasteners S3 and F1.
10. Step 10: Attach part P9 to the frame using fasteners S3 and F2.
11. Step 11: Attach part P3 to the frame using fasteners F1 and S3.
12. Step 12: Attach part P4 to the frame using fasteners S3 and F1.
13. Step 13: Attach part P4 to the frame using fasteners S3 and F1.
14. Step 14: Attach part P9 to the frame using fasteners S3 and F2.
15. Step 15: Attach part P1 to the frame using fasteners S3 and F1.
16. Step 16: Attach parts 9 and 11 to the frame.
17. Step 17: Connect parts B3, B4, 21L, 21R, and 12 to form bracing or roof structure components.
18. Step 18: Attach parts 10L and 10R to the top of the structure.
19. Step 19: Attach parts 7 and 8 to the roof structure using fastener G2.
20. Step 20: Slide parts P3 into place.
21. Step 21: Attach part 16 using fastener F3.
22. Step 22: Attach parts 4L, 4R, and 6 to the structure using fasteners S3 and F2.
23. Step 23: Attach parts P11 and P10 to the roof.
24. Step 24: Attach parts P12 to the roof.
25. Step 25: Secure roof panels P11 and P10 using fasteners F1 and S3.
26. Step 26: Attach part 19.
27. Step 27: Attach parts 17L, 17R, and GE.
28. Step 28: Attach parts 15 and GC to the roof.
29. Step 29: Connect D1, D2, and GB using fastener F2.
30. Step 30: Attach part 18 to D1&D2 using fastener F2.
31. Step 31: Attach GD using GE, S3, and F2. The shed is now complete.