SILVERGLANS Driver for Wireless Control
Manufacturer: IKEA of Sweden AB
How to Steer Your Lighting
When the driver is connected to the mains, it is possible to turn ON/OFF all products connected to the driver. To dim or connect your products to IKEA Smart lighting products, you need to purchase a separate steering device (e.g., a remote control).
The steering device must be paired with your driver(s). If you have more than one (1) driver, you can pair each one with the steering device, allowing the entire combination to be turned ON/OFF or dimmed simultaneously.
Pairing a Steering Device to Your Driver
- Connect at least one (1) product to the driver before starting the pairing process. Ensure the mains power is turned ON.
- Locate the pairing symbol on the driver. Hold the steering device close to the pairing symbol (no more than 5 cm away).
- Press and hold the pairing button on the steering device for at least 10 seconds. A red light will shine steadily on the steering device. The product connected to the driver will begin to dim and flash once to indicate that the driver is being paired to the steering device.
How to Factory Reset Your Driver
If the driver does not respond or if you wish to un-pair the driver from a steering device, you may need to perform a factory reset. The driver can be forced to factory reset by carefully pushing and holding the small button (marked RESET) with a pen tip on the driver enclosure, applying slight pressure. A factory reset can also be done by toggling the main switch 6 times.
Important Information
- The driver is for indoor use only and can be used in temperatures ranging from 5°C to 45°C (41°F to 113°F).
- Do not leave the driver in direct sunlight or near any heat source, as it may overheat.
- The declared radio range between the driver and the steering device is measured in open air. Different building materials and placement of the units can affect the wireless connectivity range.
Care Instructions
To clean the driver, wipe with a dry soft cloth. Never use abrasive cleaners or chemical solvents, as this can damage the product.
Product Servicing
Do not attempt to repair this product yourself. Opening or removing covers may expose you to dangerous voltage points or other risks.
Technical Data
| Specification | Details |
|---|---|
| Type | ICPSLC-24-30-IL44-1 |
| Input | 100-120 VAC, 50/60 Hz, 0.51A |
| Output | 24.0V DC |
| Max total load | 1.25 A, 30.0 W |
| Radio range | 10 m in open air |
| Operating frequency | 2405-2480 MHz |
| Output power | 14 dBm |
| IP-class | IP44 |
| Usage | Indoor use only |
Manufacturer: IKEA of Sweden AB
Address: Box 702, SE-343 81 Älmhult, SWEDEN
Compliance Information
This device complies with Part 15 of the FCC Rules. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE INFORMATION: According to RF exposure regulations, under normal operations, the end user shall refrain from being closer than 20 cm from the device.
License Rights and Limitations: No rights or licenses, express or implied, are granted to use third-party devices in combination with these products in a wireless mesh network, or to use third-party services to access, monitor, or control these products in a wireless mesh network via the internet or another external wide area network.
For use pursuant to U.S. Patent Nos.: US 6,914,893; US 7,697,492; US 8,964,708
Disposal Information
The crossed-out wheeled bin symbol [crossed-out-wheeled-bin] indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or landfill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store.
