FiberHome HG6245Y GPON ONU Labeling and Placement Guide

1. Material and Size Specifications

Material: White PET with permanent adhesive, coated with printable matte film.

Size: 138.5mm x 34.5mm ±0.2mm

Color: PANTONE BLACK

2. Final Label Layout and Content

Device Model: GPON ONU

Model Number: HG6245Y

Power Rating: 12V - 2.5A

FCC ID: 2AV2N-HG6245Y

WiFi 6 Certification: CE, FC CERTIFIED

Default 2.4G WLAN SSID Name: fh_nnnnnn

Default 2.4G WLAN Security: wlanxxxxxx

Default 5G WLAN SSID Name: fh_nnnnnn_5G

Default 5G WLAN Security: wlanxxxxxx

Default Terminal WEB IP: 192.168.1.1

Default Terminal WEB Username: user

Default Terminal WEB Password: user1234

MAC Address: XX-XX-XX-XX-XX-XX (Derived from production data 'MAC-START' column. Hyphens are separators. MAC address is not included in the barcode information. Requires a 12-character code readable by scanners: XXXXXXXXXXXX)

GPON SN: FHTTXXXXXXXX (Derived from production data 'SerialNO.' column. 'GPON SN:' is not included in the barcode information. Requires a 12-character code readable by scanners: FHTTXXXXXXXX)

Material Code & Production Serial Number: XXXXXXX-XXXX ZZYYYMNTXXXX (Material Code from FiberHome material number column. Production Serial Number follows general specification rules. Requires a 12-character code readable by scanners: ZZZYYYMNTXXXX)

3. Printing Rules

Font/Font Size: Helvetica Neue 65, size 5.5pt for main text, 5pt for clear text (can be slightly adjusted based on content and layout).

Barcode: 128 code. Barcode height must be no less than 3mm. Printing grade must be C or higher due to material and layout limitations.

QR Code: QR code. Size must be no less than 12x12mm. Minimum resolution 600dpi.

Spacing: Barcode spacing must be no less than 4mm.

Reading Notes: Supports scanning via mobile phones, barcode scanners, etc. Specific requirements are subject to printing rule descriptions.

General Printing: Chinese/English half-width characters are used unless otherwise specified.

Content Clarity: Content must be clear, readable, and resistant to abrasion.

RoHS Compliance: Must comply with RoHS standards. PET material must have UL certification.

Cutting: Edges must be complete. Printing should not have ink overflow, uneven color, or other defects.

4. Physical Performance Tests

Adhesion (A): A 25mm wide label is applied to a steel plate. The force required to pull the label at a 180° angle is measured. Copperplate paper/PET adhesion > 1.2KG/25mm.

Cohesion (B): A 25mm wide label is applied to a vertically fixed steel plate with an area of 25x25mm. A 1KG weight is hung for 8 hours. The label must not detach or shift.

Normal Temperature Resistance (C):

• On steel plate: Temperature range -20~100℃. After 8 hours at 80~100℃, the label must not peel, delaminate, detach, or bubble.
• On plastic/carton: Temperature range -20~65℃. After 8 hours at 65℃, the label must not peel, delaminate, detach, or bubble.

Temperature and Humidity Cycle Test (D):

• Cycle Conditions: Applied to textured plastic surface (PET); Applied to textured plastic surface/carton (copperplate paper).
• Temperature Setting: -20~60℃.
• Humidity Setting: 30~90%.
• After 96 hours, the label must not peel, delaminate, detach, or bubble.

5. Label Placement Diagrams

Detailed diagrams illustrate label placement on the following:

• Device Bottom Label: Shows the main nameplate label placement.
• Color Box Label: Shows placement on the corner of the color box.
• Collective Box Label: Shows placement on the packaging slip, facing outwards when stacked, and on both sides.
• Pallet Label: Two labels are required: one inside the protective film, and one between the two layers of protective film on the pallet.

Note: Stacking layers and methods are subject to requirement documents.

6. Revision History

5-1: 20220225 - Initial Version

5-1: 20210926 - Initial Version (This file is only for placement diagrams; if layout changes do not interfere with placement, this file will not be updated.)