Marley Stir It Up Wireless

MARLEY

ATTENTION, PLEASE READ QUICK START GUIDE BEFORE USE.

Product Map

• 1. Spindle
• 2. Turntable
• 3. 45 Adaptor
• 4. Balance Weight
• 5. Anti-Skating Knob
• 6. Tone Arm Lift Level
• 7. Tone Arm Rest Holder
• 8. Tone Arm
• 9. Stylus
• 10. Needle Cover
• 11. Off/33/45 Knob
• 12. Power Adaptor With 4 Interchangeable Plugs

Function Layout

• A. RCA Line Out
• B. Pre-Amp Switch Button
• C. USB to PC Recording
• D. Off/33/45 Knob
• E. Bluetooth® Button
• F. - VOL + Knob
• G. Headphone Jack
• H. Anti-skating Knob

Setup ⚙️

Powering On Your Stir It Up Wireless

Your Stir It Up Wireless uses an AC power supply and is powered by a standard wall outlet.

Connect the power adaptor to the wall outlet.

Bluetooth® Pairing

Power on the external Bluetooth® device first before turning on the BT function on the Turntable.

Press the BT button on the turntable to turn on the Bluetooth® transmitter.

Press the button again to enable the unit to search for the Bluetooth® device until the BT indicator light becomes solid. This indicates your devices are paired.

Indicator Status: Blue LED light flashes during search, Blue LED light stable when paired.

Disconnect Bluetooth® Pairing

Long press and hold the BT button until the BT indicator light turns off. The turntable will then disconnect from the external device.

Status: Blue LED light will turn off.

Playing a Record

1. Place a vinyl record on the turntable.
2. Assemble the balance weight and set it to a proper position.
3. To adjust the balance weight, rotate it counter-clockwise.
4. Lift and move the tone arm to the turntable. Place the tone arm on the edge of the record.
5. Turn the RPM Dial knob to select the speed according to the record you are playing (33 RPM for 33 vinyl disc, 45 RPM for 45 vinyl disc).
6. The turntable platter will auto-stop when the music has ended. Manually lift the tone arm and place it on the tone arm rest.

To listen to side B, flip the record and repeat the above steps.

To power the unit off, rotate the RPM Dial knob to the off position.

Notes on Handling:

• Remove the needle cover before balancing the tone arm.
• Hold the tone arm whenever making adjustments or actions to protect it.
• Do not adjust the balance weight while playing a record, as this could break the needle and scratch the record.
• Re-secure the tone arm before transportation to protect the needle.
• Remove the balance weight before transportation to prevent damage or breakage to the unit.
• Do not stop or turn the platter manually. Moving or jarring the turntable without securing the tone arm clamp could result in damage to the tone arm.

Anti-Skating

The anti-skating should normally be set to its minimum setting. Anti-skate compensates for inward tracking forces that occur when the stylus nears the center of the record. If the turntable experiences excessive skipping near the center spindle, try increasing the anti-skating in increments indicated on the dial. Start by adding an increment of 1, test its performance, then increase further if needed.

Note: During anti-skating adjustment, leave the tone arm and balance weight undisturbed to prevent damaging the stylus (needle).

Visual guide showing the balance weight adjustment for anti-skating, with a setting of 2.5 indicated. The text notes that settings are based on the included cartridge per a House of Marley setup video.

Volume Control

Increase Volume: Rotate the Volume Knob clockwise.

Decrease Volume: Rotate Volume Knob counter-clockwise.

Headphone Operation via Headphone Jack

Connect a set of headphones (not included) into the headphone jack.

Note: Never put on the headphones until they are plugged into the headphone jack.

USB to PC Recording

Download full instructions for the Audacity Software at: http://www.audacityteam.org/download/

• Connect the Turntable and the computer via the provided USB cable.
• Follow the software installation steps and operation interface instructions.

Non-Bluetooth® Connection Setup

CAUTION: Switch off the power to all equipment before making connections. Read the instructions of each component you intend to use with this unit. Ensure each plug is inserted securely. To prevent hum and noise, avoid bundling signal interconnection cables together with the AC power cord.

Line Out Operation

1. Switch the PRE-AMP OFF/ON SWITCH to the ON position.
2. Plug one end of the RCA cable (included) into the LINE OUT socket at the back of the unit. Ensure the color matches the socket.
3. Plug the other end of the cable into the LINE IN socket of your home amplifier device.
4. Switch on the unit and the amplifier device you connected.
5. Adjust the volume on the amplifier device.

Compliance Information ✔️

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure Statement: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

ISEDC Statement: This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The device complies with RF exposure guidelines; users can obtain Canadian information on RF exposure and compliance.

This Class B digital apparatus complies with Canadian ICES-003.

ISEDC RF Exposure Statement: The device is compliance with RF exposure guidelines; users can obtain Canadian information on RF exposure and compliance.

Battery Replacement Statement in Europe: Your Stir It Up Wireless includes a rechargeable battery designed to last the lifetime of the product. In the unlikely event that you should require a replacement battery, please contact Customer Services, who will supply details of the warranty and out-of-warranty replacement battery service.

Battery Directive: [battery disposal symbol] This symbol indicates that batteries must not be disposed of in the domestic waste as they contain substances which can be damaging to the environment and health. Please dispose of batteries in designated collection points.

WEEE Explanation: [WEEE symbol] This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Hereby, FKA Brands Ltd, declares that this radio equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be obtained from www.thehouseofmarley.co.uk/declaration-of-conformity.

To prevent possible hearing damage, do not listen at high volume levels for long periods. Full instruction and warranty details can be found at http://www.thehouseofmarley.com/instructionbooks.

Technical Specifications and Distributor Information

Manufacturer: FKA Distributing Co., LLC / China

Model Numbers: EM-JT002, EM-JT003

Product Name: Stir it Up Wireless Turntable, Simmer Down Wireless Turntable

Operation Frequency: Bluetooth (2402 – 2480 MHz)

Bluetooth Mode: BT 4.2

Output Power: 3mW

Antenna Gain: -0.58dBi

Modulation Type: GFSK, π/4-DQPSK

Power Supply: 12 V

Marley and the Marley logo are registered trademarks of Fifty-Six Hope Road Music Limited, and their use by House of Marley is under license. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc., and their use by The House of Marley is under license.

Operating frequency band: 2402 – 2480MHz

CE Maximum radio-frequency power transmitted: -5dBm

Distributed By: The House of Marley, LLC, 3000 North Pontiac Trail, Commerce Township, MI 48390 USA

Distributed in Europe By: FKA Brands Ltd., Somerhill Business Park, Five Oak Green Rd, Tonbridge, Kent TN11 0GP, UK.

Model Identifier: IB-EMJT002

Certification Marks: CE, BC

©2019 House of Marley, LLC. All Rights Reserved.