Marley Liberate Air Quick Start Guide
Attention: Please read this Quick Start Guide before use.
Inside the Box
- A. Earbuds
- B. Travel Case with Backup Battery
- C. USB to USB-C Charging Cable
- D. 2 sizes of ear tips (M, S)
- E. QSG (Quick Start Guide)
- F. Warranty Card
- G. Welcome Card
- H. Stickers
Product Overview
Legend
- A. Tap Control
- B. Earbud Status LED
- C. Microphone port
- D. Earbud Charging Contacts
- E. Case Battery Status LED
- F. USB-C charging port
- G. Force Pair Button
Function Layout
The earbuds feature tap controls on the outer surface. The status LEDs indicate power and pairing status. The case has a USB-C charging port and battery status LEDs.
Setup and Pairing
Opening the Case
Hold the case with your thumb and forefinger, and use your second hand to pull up the handle. The case closure is magnetic.
Placing Earbuds in Case
Place the earbuds into their respective cradles inside the case. When properly seated, the LED indicator light will be solid RED, indicating they are charging. A flashing RED light indicates low power.
Charging the Case
For a full charge, plug the small end of the USB to USB-C Charging Cable into the USB-C port located on the back right side of the case. When all 4 LEDs are lit, the case is fully charged.
Case Battery Status LED Indication:
- One LED Light: 25% Power
- Two LED Lights: 50% Power
- Three LED Lights: 75% Power
- Four LED Lights: 100% Power
Note: When an earbud's power level is low, an audible tone will signal every five minutes until it is placed in the charging case.
Powering On and Pairing
With the earbuds inside the charging case, open the case. They will automatically enter pairing mode.
On your device, enable Bluetooth and select "Liberate Air L" to connect the earbuds. You may receive an additional pairing request for "Headset"; accept this request.
The earbuds will now be paired to your device. Liberate Air remembers the last paired device.
Earbud Fitting
Remove both earbuds from the case. Place the Right Earbud in your right ear and the Left Earbud in your left ear. Insert by placing them vertically and rotating downwards until they rest comfortably.
Changing Eartips
To remove an eartip, grab the earbud near the nozzle with one hand, and the eargel with the opposite hand, then pry down. To attach a new eartip, place it on the nozzle and press upward until it is seated.
Advanced Features
Pairing Additional Devices
Enable Bluetooth on your device. Press and hold the Case MFB (Multi-Function Button) for 2 seconds to enter pairing mode. Select "Liberate Air L" and pair as before.
Unpairing a Device
Place the earbuds in the case with the lid closed. Then, go to your device's Bluetooth settings and select "Forget This Device." To clear the earbuds' memory, hold the MFB for six seconds until the LED lights flash red and white.
Music and Taking Calls
- Play/Pause Music: Tap the right earbud twice ([tap twice]).
- Track Control: Tap the left earbud thrice ([tap thrice]) to go to the previous track. Tap the right earbud thrice ([tap thrice]) to go to the next track.
- Answering/Ending Calls: Tap the right earbud twice ([tap twice]).
- Declining Calls: Tap the left earbud twice ([tap twice]).
Voice Command
Activate Siri, Google Assistant, or your device's supported voice assistant by tapping the left earbud twice ([tap twice]).
Master/Slave Switch & Mono Mode
Liberate Air supports a Master/Slave switch, allowing you to use either earbud independently. If one earbud powers off or has low battery, the connection will drop briefly and then re-pair to the other earbud, which will become the master. When the master earbud is placed in the charging case, the slave earbud automatically becomes the master.
Mono Mode Operation:
- Play/Pause Music: Tap the single earbud twice ([tap twice]).
- Track Control: Tap the single earbud thrice ([tap thrice]) for track forward.
- Answering/Ending Calls: Tap the single earbud twice ([tap twice]).
Compliance Information
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference. FCC RF Exposure Statement: This device complies with FCC radiation exposure limits for an uncontrolled environment. This transmitter must not be co-located or operating with any other antenna or transmitter.
ISEDC Statement (Canada)
This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference, and (2) this device must accept any interference. This Class B digital apparatus complies with Canadian ICES-003. ISEDC RF Exposure Statement: Users can obtain Canadian information on RF exposure and compliance.
Battery Replacement and Disposal
Your Liberate Air includes a rechargeable battery designed for the product's lifetime. For replacement, contact Customer Services. Batteries must not be disposed of in domestic waste; they contain substances harmful to the environment and health. Please dispose of batteries at designated collection points.
WEEE (Waste Electrical and Electronic Equipment)
This marking indicates that the product should not be disposed of with other household wastes throughout the EU. To prevent harm to the environment or human health from uncontrolled waste disposal, recycle responsibly to promote sustainable reuse of material resources.
EU Declaration of Conformity
FKA Brands Ltd. declares that this radio equipment complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be obtained from www.thehouseofmarley.co.uk/declaration-of-conformity.
FCC ID and IC Information
Left Earbud FCC ID: PVB-EM DE011, IC: 10613A-EM DE011
Right Earbud FCC ID: PVB-EM DE011R, IC: 10613A-EM DE011R
