KingForce D1F Smart Lock Installation & Operation Guide

1. Installation Guide

1.1 Prepare the Door and Check Dimensions

Ensure your door meets the following specifications using the provided template card:

• Door Frame Hole: Width 1" (25mm), Length 1-1/4" (30mm), Depth 1-1/4" (30mm).
• Door Thickness: 1-1/4" to 2" (30mm-50mm).
• Side Hole in Door: 1" (25mm).
• Backset: 2-3/8" or 2-3/4" (60mm or 70mm). Adjust the latch accordingly.
• Door Hole Diameter: 2-1/8" (54mm).

Note: Specifications are subject to change without prior notice.

1.2 Install the Latch and Striking Plate

Install the striking plate and hole-aligning device in the door frame using two screws (D). Insert the latch into the side of the door with the word "UP" facing upwards, and secure it with two screws (D).

Important: Ensure the latch bolt is fully retracted (in the unlocked position) before installation. [? Unlocked] vs [? Locked]

1.3 Install the Exterior Assembly and Mounting Plate

Insert the torque blade horizontally through the slot in the latch and route the cable below the latch. Install the mounting plate using two screws (G). Ensure screws are in the correct positions.

1.4 Adjustable Deadbolt Latch Set

To convert backset from 2-3/8" (60mm) to 2-3/4" (70mm): Rotate the latch clockwise, pull out, and twist the extension plate counter-clockwise until it locks.

To convert backset from 2-3/4" (70mm) to 2-3/8" (60mm): Rotate the latch clockwise, push in until the end, and twist the extension plate counter-clockwise until it locks.

Important: Ensure the latch bolt is fully retracted (in the unlocked position) before installation. [? Unlocked] vs [? Locked]

2. Install the Interior Assembly and Battery Cover

Connect the cable to the card slot, ensuring a tight connection. Install the interior assembly using three screws (J).

Important: Ensure the knob is in the vertical position and the latch bolt is fully retracted (in the unlocked position) before installation. [? Unlocked]

Load 4 batteries and install the battery cover. Finish the installation.

3. Detect Left/Right Hand Door Installation

Click the keypad's "KingForce" button. The lock will automatically enter the locking position. This process helps the smart lock memorize the door's orientation.

Note: Auto-lock is disabled by default. Refer to Quick Set Up 4: Set Auto Lock Time Delay to enable it.

4. Programming Instructions

4.1 Quick Set Up

Default Master Code: 123456.

Status Indicators: Red light flash indicates an error or wrong step. Long green light indicates success. All keypads flashing constantly indicates Management Mode.

Programming Steps:

1. Enter Management Mode: In lock state, press KingForce. (Long green light to proceed, Red light flash to exit).
2. Change Master Code: Press KingForce + KingForce, enter Master Code, press KingForce, enter New Master Code, press KingForce, press KingForce. (Long green light to proceed, Red light flash to exit).
3. Add User Code / Add User Fingerprint:
   • User Code: Press KingForce + KingForce, enter Master Code, press KingForce, enter New User Code, press KingForce. (Long green light to proceed, Red light flash to exit).
   • User Fingerprint: Press KingForce + KingForce, enter Master Code, press KingForce, scan fingerprint 8 times. (Long green light to succeed, Red light flash to exit). Repeat step 2 to add more users.
4. Set Auto Lock Time Delay: Press KingForce + KingForce, enter Master Code, press KingForce, enter new duration time (10-99 seconds; 0 seconds disables auto-lock). (Long green light to succeed, Red light flash to exit).
5. Add One-Time Code: Press KingForce + KingForce, enter Master Code, press KingForce, enter New User Code, press KingForce. (Long green light to succeed, Red light flash to exit).
6. Vacation Mode: Press KingForce + KingForce, enter Master Code, press KingForce. Select "Vacation Mode Disabled" or "Vacation Mode Enabled". (Long green light to succeed, Red light flash to exit).

   Note: Enabling Vacation Mode restricts all user codes until the Master Code is entered. Using the Master Code to unlock or enter management mode disables Vacation Mode.

7. Voice Setting: Press KingForce + KingForce, enter Master Code, press KingForce. Select "Voice Disabled" or "Voice Enabled". (Long green light to succeed, Red light flash to exit).
8. Delete User Code / Delete User Fingerprint:
   • User Code: Press KingForce + KingForce, enter Master Code, press KingForce, enter Unwanted User Code, press KingForce. (Long green light to succeed, Red light flash to exit).
   • User Fingerprint: Press KingForce + KingForce, enter Master Code, press KingForce, scan fingerprint once. (Long green light to succeed, Red light flash to exit).

5. Definitions

• Master Code: Required for programming and feature settings. Can be used to unlock the door in Vacation Mode. Keep this confidential.
• Auto Lock: The lock automatically locks after a set time delay after unlocking.
• Wrong Entry Limit: After 10 unsuccessful PIN code attempts, the unit shuts down for 30 seconds.
• Silent Mode: Mutes beep sounds from the keypad, but audible alerts remain.
• Vacation Mode: A security feature that restricts all user codes when enabled. User codes are only accessible after entering the Master Code.
• Unlock Direction: The lock automatically determines and records the unlocking direction upon the first successful unlock/lock operation. Manual turning of the knob does not record direction. To change, disconnect and reconnect power, then perform one successful unlock/lock.
• Unlock Method: Enter password and press KingForce, manually turn the knob, or press a registered fingerprint.
• Locking Method: Click KingForce to lock, manually turn the knob to lock, or auto-lock if enabled.
• Low Battery Alarm: When the battery voltage drops below 4.8V (±0.1V), a low power voice alert is issued upon successful unlock.
• Emergency Power Supply: The USB Type-C interface on the front panel can be connected to a mobile power supply for emergency unlocking.

6. Restore To Factory Default Settings

Default Master Code: 123456.

1. Open and unlock the door.
2. Remove one battery. Press a random keypad button to drain remaining power.
3. Press and hold the Reset Button (K) with the Reset Tool. While holding, replace the battery.
4. Continue holding the Reset Button until you hear a "succeeded" voice prompt. If you hear "failed", repeat from step 1.

7. Parts Illustrations

Exterior Assembly

• Keypad
• Multi-Function Button (KingForce)
• Cylinder

Interior Assembly

• Battery Cover
• Knob
• Reset Button

8. Get 24/7 Assistance

Visit: https://kingforce.afterservice.vip

Email: kingforce@afterservice.vip

Call: +1 (888) 839 1709