Endgame Gear OP1w 4k Wireless Gaming Mouse

Product Specifications

• Product Type: Wireless Gaming Mouse / Wireless Gaming Mouse Dongle
• Model Name: OP1w 4k
• Mouse FCC ID: 2A7CL-EGG005
• Dongle FCC ID: 2A7CL-EGG004D
• Radio Frequency: 2.4GHz SRD
• Operation Frequency Range: 2402-2480MHz
• Max. Output Power (dBm): Mouse: 7.33, Dongle: 5.42
• Modulation Type: GFSK

Ergonomic Information

Extended periods of repetitive motion, improper workspace setup, poor posture, and incorrect work habits may lead to physical discomfort and injury to nerves, tendons, and muscles. If you experience any pain, numbness, weakness, swelling, burning, cramping, or stiffness in your hands, wrists, arms, shoulders, neck, or back, consult a qualified health professional.

Safety Instructions

• Do not immerse the product in any liquid or expose it to heat and/or moisture, as moisture can corrode the inner electronics.
• The wireless mouse is not intended for use by children under 14 years old unless under the supervision of an adult.
• Operate the product within the temperature range of 0°C (32°F) to 40°C (104°F). If exposed to temperatures outside this range, power off the device until the temperature stabilizes within the specified operating range.

Proper Handling and Disposal

• Disconnect the USB cable and move the on/off switch to the off position before opening the product.
• Open the product only in a clean and dry environment with dry hands.
• Dispose of batteries, electronic, and electrical equipment at appropriate collection points to enable recycling and prevent environmental impact.
• Disassemble the product only to replace the switches.

Compliance Statements

The Endgame Gear OP1w 4k complies with relevant legal requirements for Restriction of Hazardous Substances (RoHS), management of waste electronic and electrical equipment (WEEE), EMC directive, and Product Safety.

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

NCC Statement

Obtaining certification for low-power radio frequency equipment does not authorize the company, firm, or user to modify the frequency, increase power, or change the characteristics and functions of the original design without approval. The use of low-power radio frequency equipment must not interfere with aviation safety and legitimate communications. If interference is detected, it should be immediately discontinued and improved until the interference is eliminated before resuming use. Legitimate communications refer to wireless radio communications conducted in accordance with telecommunications regulations. Low-power radio frequency equipment must tolerate interference from legitimate communications or industrial, scientific, and medical radio wave-emitting electrical equipment.

Warranty and Support

The Endgame Gear OP1w 4k Wireless Gaming Mouse is covered by a limited warranty depending on the regulations of your country of purchase. Please refer to the warranty terms and conditions of your reseller for details.

For warranty claims or support inquiries, contact Endgame Gear’s customer service email or visit the support website help.endgamegear.com.

Copyright and Authorization

The copyright of this document belongs exclusively to Pro Gamersware GmbH. It is prohibited to copy, use, reproduce, offer, or distribute this design without written authorization. All rights reserved.

Manufactured on behalf of: Pro Gamersware GmbH, Gaussstrasse 1, 10589 Berlin, Germany

Product design & quality control: in EU, Made in China

Document Version: v1.0, February 2024

Contact Information

• Support Email: customerservice@endgamegear.com
• Support Website: help.endgamegear.com
• Support Discord: discord.gg/endgamegear

Quick Start Guide

Package Contents

The package includes the Endgame Gear OP1w 4k mouse, a USB dongle, a USB-C charging cable, and a mouse dock/stand.

Connection

1. Plug the USB dongle into your computer.
2. Turn the mouse on using the power switch located on the bottom of the mouse. The indicator LED will show the status.

Charging

Connect the USB-C cable to the mouse and a power source. The indicator LED will show the charging status.

Downloads

Visit www.endgamegear.com/downloads for more information.

Button Functions

• 1. Back side-button
• 2. Front side-button
• 3. Left mouse button
• 4. Right mouse button
• 5. Scroll wheel / middle mouse button
• 6. Power switch
• 7. Mode button

Indicator LED

• Battery Level: 100-71% (green), 70-41% (yellow), 40-11% (orange), 10-0% (blinking red).

Mode Button Functionality

• Short press: Cycles through default CPI settings: 400CPI (blue), 800CPI (green), 1600CPI (yellow), 3200CPI (red).
• Long press: Cycles through polling rate settings: 4000Hz (indicated by 4 flashes), 2000Hz (indicated by 2 flashes), 1000Hz (indicated by 1 flash).