STABILA LD 320

Introduction and Safety

The safety instructions and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to them.

Symbols Used

• WARNING: Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
• CAUTION: Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage.
• Important: Paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.

Overview

The device features a display, control buttons, and a laser emitter. Key areas include: Display, On/Measure/Tracking button, Area/Volume/Pythagoras/Min/Max Tracking button, Clear/Off button, and Measuring reference/Unit indicator.

Instrument Set-up

Display Elements

The display shows Battery status, Area/Volume mode, Measuring reference point (front or rear of device), Info messages, Min/Max tracking status, Measurement units, and the Main measurement line.

Inserting Batteries

To ensure reliable use, do not use zinc-carbon batteries. Change batteries when the battery symbol is flashing. The device uses 2 x AAA batteries.

Operations

Switching ON/OFF

Press the 'Clear/Off' button for 2 seconds to turn the device ON or OFF.

Clear / Undo Last Action

Press the 'Clear' button once to undo the last action. Press it twice to leave the current function and return to the default operation mode.

Message Codes

If the 'Info' icon appears with a number, refer to the "Message Codes" section for details. For example, code 256 indicates a received signal that is too high, suggesting changing the target surface (e.g., to white paper).

Adjusting Measuring Reference

The measuring reference can be set to the front of the device (default) or the rear. When set to the front, the next distance is measured from the front. When set to the rear, it's measured from the rear.

Distance Unit Setting

Press and hold the 'Clear/Off' button for 2 seconds to switch between units such as meters (m), feet (ft), inches (in), and feet/inches with fractions.

Beep ON/OFF

Press and hold the 'On/Measure/Tracking' and 'Clear/Off' buttons simultaneously for 2 seconds to toggle the beep function ON or OFF.

Measuring Functions

Measuring Single Distance

Aim the active laser at the target and press the 'On/Measure/Tracking' button. The measured distance is displayed.

Permanent Measuring (Tracking)

Aim the active laser at the target. Press and hold the 'On/Measure/Tracking' button for 2 seconds. The device continuously measures and displays the distance. Press the button again to stop.

Area Measurement

Press the 'Area/Volume/Pythagoras/Min/Max Tracking' button once (1x) to select Area mode. Aim the laser at the first target point, press 'On/Measure/Tracking'. Aim at the second target point, press 'On/Measure/Tracking'. The result is shown in the main line and the measured value above.

Volume Measurement

Press the 'Area/Volume/Pythagoras/Min/Max Tracking' button twice (2x) to select Volume mode. Aim at the first target point, press 'On/Measure/Tracking'. Aim at the second target point, press 'On/Measure/Tracking'. Aim at the third target point, press 'On/Measure/Tracking'. The result is shown in the main line and the measured value above.

Pythagoras (2-point)

Press the 'Area/Volume/Pythagoras/Min/Max Tracking' button three times (3x) to select 2-point Pythagoras mode. Aim at the upper point, press 'On/Measure/Tracking'. Aim at the lower point, press 'On/Measure/Tracking'. The result is displayed. Pressing the measuring key for 2 seconds activates automatic Minimum or Maximum measurement.

Pythagoras (3-point)

Press the 'Area/Volume/Pythagoras/Min/Max Tracking' button four times (4x) to select 3-point Pythagoras mode. Aim at the upper point, press 'On/Measure/Tracking'. Aim at the rectangular point, press 'On/Measure/Tracking'. Aim at the lower point, press 'On/Measure/Tracking'. The result is displayed. Pressing the measuring key for 2 seconds activates automatic Minimum or Maximum measurement.

Minimum Tracking

Press the 'Area/Volume/Pythagoras/Min/Max Tracking' button five times (5x) to select Minimum Tracking. Aim the laser at the target. Press and hold the 'On/Measure/Tracking' button for 2 seconds. The device tracks the minimum distance measured. The current measured value and minimum distance are displayed.

Maximum Tracking

Press the 'Area/Volume/Pythagoras/Min/Max Tracking' button six times (6x) to select Maximum Tracking. Aim the laser at the target. Press and hold the 'On/Measure/Tracking' button for 2 seconds. The device tracks the maximum distance measured. The current measured value and maximum distance are displayed.

Note: Min/max measurement is also available for Pythagoras calculations.

Technical Data

Distance Measurement

• Accuracy (favourable conditions): ±1.5 mm / 0.06 in
• Accuracy (unfavourable conditions): ±3.0 mm / 0.12 in
• Range (favourable conditions): 0.05 - 60 m / 0.16 - 197 ft
• Range (unfavourable conditions): 40 m / 132 ft
• Smallest unit displayed: 1 mm / 1/16 in

Laser

• Laser Class: 2
• Laser Type: 636 nm, < 1 mW
• Automatic laser switch-off: after 90 s
• Automatic power switch-off: after 180 s

Power

• Battery durability (2 x AAA): up to 5000 measurements

General

• Dimensions (H x D x W): 100 x 54 x 30 mm / 3.94 x 2.13 x 1.18 in
• Weight (with batteries): 100 g / 3.53 oz
• Temperature range (Storage): -25 to 70°C / -13 to 158°F
• Temperature range (Operation): 0 to 40°C / 32 to 104°F

Accuracy & Range Notes

Favourable conditions include white, diffuse reflecting targets, low background illumination, and moderate temperatures. Unfavourable conditions involve targets with lower/higher reflectivity, high background illumination, or extreme temperatures. Tolerances may increase with distance and unfavourable conditions.

Functions Supported

• Distance measuring: Yes
• Min/Max measuring: Yes
• Permanent measuring: Yes
• Area: Yes
• Volume: Yes
• Pythagoras (2-point, 3-point): Yes
• Display illumination: Yes

Message Codes

If the "Error" message does not disappear after switching on the device repeatedly, contact the dealer. If the "Info" message appears with a number, press the Clear button and observe the following:

Care and Maintenance

• Clean the device with a damp, soft cloth.
• Never immerse the device in water.
• Never use aggressive cleaning agents or solvents.

Warranty

STABILA provides a two-year warranty for the STABILA LD 320. Further information can be found on the Internet at: www.stabila.de.

Safety Instructions

The person responsible for the instrument must ensure that all users understand these directions and adhere to them.

Areas of Responsibility

Responsibilities of the manufacturer of the original equipment:

STABILA Messgeräte Gustav Ullrich GmbH, P.O. Box 1340/D-76851 Annweiler, Landauer Str. 45/D-76855 Annweiler. The company is responsible for supplying the product, including the User Manual, in a completely safe condition.

Responsibilities of the person in charge of the instrument:

• To understand the safety instructions on the product and in the User Manual.
• To be familiar with local safety regulations relating to accident prevention.
• Always prevent access to the product by unauthorised personnel.

Permitted and Prohibited Use

Permitted Use

• Measuring distances
• Tilt measurement

Prohibited Use

• Using the product without instruction.
• Using outside the stated limits.
• Deactivation of safety systems and removal of explanatory and hazard labels.
• Opening the equipment with tools.
• Carrying out modification or conversion of the product.
• Use of accessories from other manufacturers without express approval.
• Deliberate dazzling of third parties.
• Inadequate safeguards at the surveying site (e.g., on roads, construction sites).
• Deliberate or irresponsible behaviour on scaffolding, when using ladders, or near unprotected machines.
• Aiming directly in the sun.

Hazards in Use

WARNING

Watch out for erroneous measurements if the instrument is defective, dropped, misused, or modified. Carry out periodic test measurements, especially after abnormal use.

CAUTION

Never attempt to repair the product yourself. In case of damage, contact a local dealer.

WARNING

Changes or modifications not expressly approved could void the user's authority to operate the equipment.

Limits of Use

Refer to section "Technical Data". The device is designed for use in areas permanently habitable by humans. Do not use in explosion hazardous areas or in aggressive environments.

Disposal

CAUTION

Flat batteries must not be disposed of with household waste. Take them to designated collection points. The product must not be disposed of with household waste. Dispose of the product appropriately according to national regulations.

Electromagnetic Compatibility (EMC)

The device conforms to stringent requirements. However, interference in other devices cannot be totally excluded.

FCC Statement (USA)

This equipment complies with FCC Rules for Class B digital devices. It generates, uses, and can radiate radio frequency energy. If interference occurs, try measures like reorienting the antenna, increasing separation, or consulting a dealer/technician.

Laser Classification

The device produces visible laser beams and is a Class 2 laser product according to IEC60825-1:2007. Do not stare into the laser beam or direct it towards people. Eye protection is normally afforded by aversion responses (blink reflex).

WARNING

Looking into the beam with optical aids (binoculars, telescopes) can be hazardous.

CAUTION

Looking into the laser beam may be hazardous to the eyes.

Labelling

Labels include: "Do not stare into the beam", "Laser class 2", "acc. IEC 60825-1:2007", "Maximum radiant power: <1mW", "Emitted wavelength: 620-690nm", "Beam divergence: 0.15 x 0.6 mrad".

CE Conformity

This declaration, dated March 16, 2012, confirms adherence to Directive 2004/108/EC (interference emission and resistance) and Directive 2011/65/EU (restriction of hazardous substances). Product Type: STABILA LD 320 Laser distance measuring instrument. Applied standards include EN 50011:2010, IEC 61000-4-3:2010, and IEC 61000-4-8:2010. Signed by Dipl. Ing. (FH) Daniel Busam.

Company Information

Germany (Headquarters)

STABILA Messgeräte Gustav Ullrich GmbH
P.O. Box 13 40/D-76851 Annweiler
Landauer Str. 45/D-76855 Annweiler
Tel.: +49 (0) 6346/309-0
Fax: +49 (0) 6346/309-480
e-mail: info@stabila.de
www.stabila.de

USA / Canada

STABILA Inc.
332 Industrial Drive
South Elgin, IL 60177
1.800.869.7460
www.stabila.com