Aqara Smart Plug Quick Start Guide
Product Introduction
The Aqara Smart Plug is designed to control the power supply of home appliances, turning them on or off. It integrates with an Aqara Hub to enable advanced functions such as remote control via the Aqara app and scheduled timing control. When used with other Aqara smart accessories, it contributes to an engaging and comfortable smart home experience.
Requirements:
- An Aqara Hub is required for operation.
- An Aqara Hub is also necessary for the Smart Plug to work with Apple HomeKit technology. For more details, please visit www.aqara.com.
- This product is intended for indoor use only.
Product Overview
The smart plug features a compact, cube-shaped design. The front face includes a standard electrical outlet with two vertical slots and a U-shaped ground slot. The top face is equipped with a small circular indicator light and a prominent push button. The side view shows the plug prongs designed for insertion into a wall socket.
Key Components:
- Indicator Light: Provides status information about the device's connection and operation.
- Power Outlet: The socket where appliances are plugged in.
- Push Button: Used for manual control, pairing, and testing.
Push Button Functions:
- Short Press Once: Turns the connected appliance on or off.
- Long Press for 5 seconds: Initiates the reconnection process.
- Quick Press 5 Times: Performs an Effective Range Test.
Installation
Plug the Aqara Smart Plug into a power outlet. Upon successful connection to power, the blue indicator light will blink once, indicating the power supply is working properly. A short press of the push button will cause the red indicator light to blink slowly, signifying that the Smart Plug is functioning correctly.
Quick Setup
- Ensure your Aqara Hub is added to the Aqara app by following the instructions in the Hub's Quick Start Guide.
- Open the Aqara app. Navigate to the "Home" screen, then tap the "+" icon in the top right corner to access the "Add Device (Accessory)" page.
- Select "Smart Plug" from the list of devices and follow the on-screen instructions to complete the setup.
Troubleshooting: If the connection fails, try moving the Smart Plug closer to the Hub, plug it in again, and repeat the setup process.
Effective Range Test:
To verify the communication range, quickly press the push button on the Smart Plug five times. If the Aqara Hub provides voice prompts, it confirms that the accessory can communicate effectively with the Hub.
Identifying an Accessory:
To identify the Smart Plug within the app: Open the Aqara app, go to the "Device List (Accessories)" page. Quickly press the push button on the Smart Plug five times. If the Aqara Hub emits voice prompts and the corresponding accessory icon blinks in the app, the accessory has been successfully identified.
Note: This identification feature is supported by the Aqara Home app and the Aqara app.
Indicator Light Status
| Indicator Light Status | Status Description |
|---|---|
| Blue light blinks quickly | Zigbee network is connecting |
| Blue light keeps on | Zigbee network works properly |
| Red light blinks quickly | Overload and high temperature alarm |
| Red light blinks slowly | Zigbee network is not connected |
Specifications
- Model: ZNCZ12LM
- Dimensions: 67 x 47 x 35 mm (2.64 x 1.85 x 1.38 in.)
- Wireless Protocol: Zigbee
- Electrical Rating: 1875 W, 15 A, 100 – 125 V AC, 60 Hz
- Operating Temperature: -10°C to +40°C
- Operating Humidity: 0 – 95% RH, no condensation
Contact Information:
- Online Customer Service: www.aqara.com/support
- Email: support@aqara.com
- Manufacturer: Lumi United Technology Co., Ltd.
- Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China.
Compliance Information
FCC Compliance:
FCC ID: 2AKIT-ZNCZ12LM
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
IC Compliance (Canada):
IC: 22635-ZNCZ12LM
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
