FP2070 SERIES

QUICK START GUIDE

Product Code

FP2070T-V2: 800 x 480, WVGA, 7" color TFT with 4-wire analog resistive touch screen with 2 serial ports, one USB Type C port & 1 USB Host port.

FP2070TN-V2: 800 x 480, WVGA, 7" color TFT with 4-wire analog resistive touch screen with 2 serial ports, one USB Type C port, one USB Host port & 1 Ethernet Port.

FP2070T-E: 800 x 480, WVGA, 7" color TFT with 4-wire analog resistive touch screen with 2 serial ports, one USB Type C port & 1 USB Host port. It supports upto 3 expansions.

FP2070TN-E: 800 x 480, WVGA, 7" color TFT with 4-wire analog resistive touch screen with 2 serial ports, one USB Type C port, one USB Host port & 1 Ethernet Port. It supports upto 3 expansions.

GETTING STARTED

User should follow the given sequence to configure and use any FlexiPanels series unit:

Install FlexiSoft Software.
Create a PZM application using FlexiSoft software.
Connect programming cable.
Download Firmware i.e. driver for the HMI.
Download application.
Now FP unit is ready to use in the system.

For More Information, Visit https://www.renuelectronics.com

SPECIFICATIONS

	Specifications	Product Dimensions
Power (Base)	24VDC (+20%) @200mA, 4.8W (T-V2 module)	7", 800 x 480 pixels, WVGA color TFT with 4-wire analog resistive touch screen
Power	24VDC (+20%, -15%) @230mA, 5.52W (TN-V2 module)
Power (With 3 Expansions)	24VDC (+20%) @220mA, 5.28W (T-E type module) 24VDC (+20%) @250mA, 6W (TN-E type module)
Display	7", 800 x 480 pixels, WVGA color TFT with 4-wire analog resistive touch screen
LEDs	1
RAM	32MB max.
User Application	8MB
Ladder Memory	2MB
Alarm Memory	1350 Alarms
Retentive Memory	8000 Words
Data Log	4MB
Keep Memory Registers	1000 Words
Panel Cutout Dimensions	127.00(H) x 175.00(W)mm	PANEL CUTOUT DIMENSIONS 175.0 127.0 R3.0(4X) 57.5 31.00 5.00 Panel Cutout Dimensions: 127(H) x 175.00(W)mm Panel Thickness: Maximum 6mm Mounting Clamps: 4 Tighten the mounting screws evenly to a torque between 0.4N/m to maintain water and dust resistance.
Dimensions	138(H) x 186.0(W) x 31.0(D)mm	186.00 174.00 126.00 138.00
Weight	Approx. 400gm
Communication	2 x RS232/RS485
USB Ports	1 USB Type C & 1 USB Host
SD card	Micro SD card supported (4 to 32 GB)
Ethernet	1 Ethernet Port
Expansions*	Supports 3 Expansion slot
Environment & Approvals	Operating Temperature 0°C to 50°C Storage Temperature -30°C to 85°C Humidity 10 to 90% (Noncondensing) Shock 25g, 11ms, 6 shocks per axis, Total 18 shocks (X, Y, Z) Vibration 5~150Hz, 3g peak, (X, Y, Z) Protection Front panel-IP66, Rare panel-IP20
APPROVALS	CE, UL (Class 1 DIV 2), UKCA, REACH& RoHS [*Note: Applicable only for FP2070Tx-E models. #Note -Applied for FP2070TN-V2 and FP2070TN-E model]

Earthing

The optimum method for Earthing electronic equipment is to earth it separately from other high-power systems, to earth more than one unit of electronic equipment with a single-point earth. The Earthing marked terminal (see below) is provided on the unit.

DC+ DC- Earth
24Vdc

[Note: Do not use an earth that has an unstable impedance, such as painted screws or earth subject to vibration.]

COMMUNICATION

This section provides information regarding communication interfaces supported by this product.

COM1

FP2070Tx-E has one terminal block port (COM1) which support RS232 / RS485 signal levels.

2-wire RS485 pinout

Pin number	Signal
1	TX+
2	TX-
3	RX+
4	RX+
5	GND and Shield
6	RX-
7	NC
8	NC
9	TX-
10	RX-

4-wire RS485 pinout

Pin number	Signal	Pin number	Signal
1	TX+	1	TX+
4	RX+	4	RX+
5	GND and Shield	5	GND and Shield
8	TX-	8	TX-
9	RX-	9	RX-

USB Type C Port

USB Type C, compliant with USB 2.0 specification, self-powered device.
Connector used: Micro USB Type C Female connector.

COM2

FP2070Tx-E has one DB9 female port (COM2) which support RS232 / RS485 signal levels.

Pin No.	Signal
1	DB9 em(RS422/RS485)
2	TXD(RS232)
3	RXD(RS232)
4	RX+(RS422/RS485)
5	GND
6	NC
7	NC
8	TX-(RS422/RS485)
9	RX-(RS422/RS485)

Cables:

RS232 pinout

Pin number	Signal	Pin number	Signal
2	TXD	2	RXD
3	RXD	3	TXD
5	GND	5	GND

Ethernet Port

Fully compliant with IEEE 802.3 / 802.3u standards.
10/100 Mbps support.
Connector used: Standard shielded RJ-45 female jack with in-built speed and link activity indication LEDs.
Default IP Address: 192.168.0.254
Default Subnet Activity Mask: 255.255.255.0

UL APPROVAL

CONTROL DRAWING NO# CNTL/DWG/FP2070/0218	VER.NO.: 1.00
Hazardous Location	Non-Hazardous Location
Class I Division 2 Groups A B C and D
FP2070	Associated Apparatus
	USB Port
JP5 V max = 3.3 VDC I max = 150 mA L = 0 C = 9 pF	Voc, Isc, La and Ca to be determined per Table 1

TABLE 1:

Nonincendive. Equipment	Associated Apparatus
V max (or Ui)	Voc or Vt (or Uo)
I max (or Ii)	Isc or It (or Io)
Ci + Ccable	Ca (or Co)
Li + Lcable	La (or Lo)

Capacitance and inductance of the field wiring from the nonincendive equipment to the associated apparatus shall be calculated and must be included in the system calculations as shown in Table 1. Where the cable capacitance and inductance per foot are not known, the following values shall be used: Ccable = 60 pF/ft., Lcable = 0.2 pH/ft. Wiring method must be in accordance with ANSI/NFPA70

REVISION HISTORY

Rev.	Description	Date
1.0	First Draft	14/08/2020
1.1	Added Website Information	27/08/2020
1.2	Updated Communication Information	07/09/2020
1.3	Updated IP rating	02/06/2021
1.4	Replaced USB type from Micro to Type C	11/10/2021
1.5	Remove Micro USB Pinout dia	08/12/2021
1.6	Logo Updated	20/09/2022
1.7	Specification updated	09/06/2025

RENU Electronics Pvt. Ltd® reserves the right to change or discontinue specifications and features without prior notice.

	FlexiPanels FP2 V2 Basic HMI Series Datasheet Datasheet for the RENU FlexiPanels FP2 V2 Basic HMI series, featuring a 7" Color TFT display, analog resistive touch screen, and various communication options.
	Renu FlexiPanels FP2 V2 Basic HMI Series Datasheet Datasheet for the Renu FlexiPanels FP2 V2 Basic HMI series, featuring a 7" TFT display, analog resistive touch screen, and various communication and environmental specifications.
	FP2070TN-LE2016RP-A0402U Quick Start Guide This guide provides a quick start overview for the RENU FP2070TN-LE2016RP-A0402U HMI panel, detailing its specifications, product dimensions, panel cutout dimensions, and communication interfaces.
	FP2043 Series Quick Start Guide A quick start guide for the FP2043 Series of devices, detailing specifications, communication interfaces, and getting started instructions.
	FP2070TN-LE2016RP-A0402U FlexiPanels FP2 HMI Datasheet Detailed specifications and features of the RENU FlexiPanels FP2 FP2070TN-LE2016RP-A0402U, a 7-inch color TFT HMI with local and pluggable I/Os, offering advanced controller functions and robust connectivity.
	FlexiPanels FP2 V2 Basic HMI Series Datasheet Datasheet for the RENU FlexiPanels FP2 V2 Basic HMI series, featuring a 4.3" color TFT display, RS232/RS485 communication, and industrial approvals.
	FlexiPanels FP2 V2 Basic HMI Series: Technical Specifications and Features Explore the FlexiPanels FP2 V2 Basic HMI series, featuring a 4.3" color TFT display, robust connectivity options including RS232, RS485, USB, and Ethernet, and compliance with CE, UL Class I Div 2, RoHS, and IP66 standards. This document details model specifications, supported protocols, and application examples.
	Renu FP4070 Series Quick Start Guide A quick start guide for the Renu FP4070 Series HMI, detailing specifications, product dimensions, communication interfaces, and UL approvals.