Rollei Rock Solid Beta / Gamma Mark III Carbon Tripod

Before the First Use

Before using the product for the first time, read the operating instructions and the safety instructions carefully. Keep the operating instructions together with the product for later use. If other people use this product, please make these instructions available to them. If you pass the product on to third parties, these instructions belong to the product and must be supplied with it.

Components of the Tripod [A]

Diagram A illustrates the main components of the tripod. The numbered parts are:

1. Mounting plate
2. Central column lock
3. Angle-adjusting button
4. Leg
5. Leg lock
6. Central column
7. Hook
8. 3/8" and 1/4" mounting screw
9. Counter screw A
10. Counter screw B
11. Spikes
12. Hex wrench 3 mm
13. Hex wrench 4 mm (2x)
14. Short central column
15. Ball head
16. 1/4" and 3/8" threads

Tripod Folding [B]

To fold the tripod for compact storage and transport:

1. Retract all sections of the legs and lock them securely.
2. Pull out the angle-adjusting button (labeled 'a' in diagram B) to adjust the leg angle.
3. Simultaneously reverse all legs (as shown in diagram B, image 'b') to achieve the smallest possible size for easy carrying.

Technical Data

Design and technical data are subject to change without notice.

Using the Tripod

A. Quick Locking/Releasing Legs System

To extend or retract the tripod legs:

1. Turn the leg lock (5) clockwise approximately half a turn to extend or shorten the legs [1].
2. Tighten the leg lock (5) by turning it counterclockwise after adjusting the leg length [2].

B. Tripod with Short Center Column

To use the tripod with a short center column:

1. Turn the hook (7) counterclockwise to remove it. Loosen the central column lock (2) and remove the central column (6).
2. Insert the short central column (14) into the central column housing and tighten the central column lock (2).
3. Set the tripod legs to their widest angle and screw the mounting plate (1) onto the short central column.

C. Upside-Down Central Column for Macro Angle Shooting

The central column can be inverted to facilitate macro photography, allowing for lower shooting angles.

D. Converting the 3/8" Screw to a 1/4" Screw

To change the mounting screw size:

1. Turn the mounting plate (1) for the tripod head counterclockwise and remove the tripod screw from the plate.
2. Flip the 3/8"-1/4" mounting screw (8) and reinsert it into the mounting plate. Rotate the mounting plate (1) clockwise to secure it.

E. Attaching the Ball Head

To mount the ball head onto the tripod:

1. Ensure the panning base is locked by tightening the panning knob.
2. Screw the ball head onto the tripod using the 3/8" screw thread on the bottom of the head. If your tripod has a 1/4" screw, use an adapter (not included).
3. Use the small screw on the tripod plate to firmly secure the ball head, preventing accidental detachment.

F. Camera Attachment

To attach your camera:

1. Attach the quick release plate to the underside of your camera.
2. Open the clamp lock by turning it counterclockwise.
3. Insert the quick release plate [a] by first placing one side into the groove and then pressing the other side down.
4. If the plate is correctly positioned, tighten the clamp lock again [b].

G. Main Fixation

After setting the desired angle for your camera, tighten the main fixation clockwise to secure the position.

H. Fine Adjustment

Turn the fine adjustment clockwise. This allows for precise adjustments while the ball head remains partially fixed.

To completely lock the ball head, tighten both adjustment screws.

I. Panorama Axis

To pan your camera:

1. Loosen the swivel lock and turn the head counterclockwise or clockwise to the desired position.
2. Fix the position by turning the swivel lock clockwise.

J. Changing Rubber Feet to Spikes

To switch between rubber feet and spikes:

1. Turn the rubber feet clockwise to loosen them [1].
2. Screw the spikes (11) into the tripod leg plates using the appropriate hex wrench [2].

General Information

• Temperature Range: -40 °C to +100 °C.
• The tripod is resistant to saltwater.
• If necessary, clean the locking system and moving parts with a soft towel and a mild detergent.
• For smooth operation, use conventional lubricants or wax oil if needed.