Smart Door Lock H6 User Manual

⚠️ IMPORTANT NOTES

• ⚠️ Install and test the lock with the door open to avoid being locked out.
• ❌ DO NOT install the batteries before installing the lock!
• ▶️ Follow the instructions in sequential order!
• ? Please must use AA Alkaline Battery and don't use Lithium Battery or Rechargeable Battery.
• ⚡ Please replace for the battery when low wattage alarm.
• ? Reading this manual carefully before installation, and keep it for future reference.

1. Product Overview

Battery Case: Used to insert 4 AA Alkaline Batteries.

Privacy Mode Button: ? Privacy Mode Button

Keypad Fingerprint Reader: Used to verify your finger and unlock from outside.

Micro USB: ? Micro USB. Used to connect a power bank to activate the lock when the battery runs out. (It cannot charge the lock's battery).

Keyhole: ? Keyhole. Used to insert a key to unlock in emergency situations.

Knob: ? Knob. Used to lock and unlock the door from inside.

Keypad: ? Keypad. Used to enter the password and unlock from outside.

2. Packing List

• Exterior Assembly * 1
• Interior Assembly * 1
• Mortise * 1
• Rubber Plate * 2
• User Manual * 1
• Strike & Strike Box * 2
• Mechanical Key * 2
• Pin of spindle * 1
• Sliding Screw A * 1
• Screw Cover
• Screw B * 4
• Screw C * 4
• Screw D * 1
• Screw E * 1
• Square Shaft * 1
• Screw Casing * 2

3. Introduction

3.1. Lock Structure

Diagram illustrating the lock's internal and external components.

3.2. Specifications

3.3. Electronic Locking Button

If you want to use the Electronic Locking function, first enable "privacy lock" in the app. When the button is in the ? Red state, it is ? Locked. In this state, it can only be unlocked via the administrator app or a mechanical key.

4. Installation

4.1. Adjust the Handles Direction

Notice: Adjust the handle according to the direction you open the door.

For Exterior Assembly:

1. Loosen the screw ?.
2. Adjust the door handle.
3. Tighten the screws ? after adjusting the handle direction.

For Interior Assembly:

1. Loosen the screw ?.
2. Adjust the door handle.
3. Tighten the screws ? after adjusting the handle direction and complete ✔️.

4.2. Installation Diagram (For 5572)

Step 1: Install Mortise

Install the mortise into the door using Screw C ? and fix it.

Step 2: Install Exterior Assembly

1. Install the waterproof rubber plate to the exterior assembly.
2. Install the square shaft into the spindle hub.
3. Install the exterior assembly with screw casings ?.
4. Install the exterior assembly.

Step 3: Install Interior Assembly

1. Install the waterproof rubber plate to the interior assembly and loosen the Battery cover screws ?.
2. Connect the wire ?.
3. Secure the Mounting plate with Screw D ? and Screw E ?.

Step 4: Install Batteries

1. Insert 4 AA alkaline batteries ?.
2. Install the battery cover.
3. Installation Complete ✔️.

5. System Initialization

Open the cover plate of the front panel, long press the "? Reset" button on the back panel for 5 seconds, then press "000#". Initialization is complete.

6. Operation

6.1. Registration

The TTLock app (iOS version) can be downloaded from the App Store ?, and the Android version from Google Play ▶️. Register a new account (phone number or email) or log in with an existing account.

6.2. Connect lock to the phone

1. Scan the QR code ? to download the app, or search for "TTLock" in the App Store ? or Google Play ▶️.
2. Register a new account (phone number or email) ✍️ or log in with an existing account ?.
3. Touch the lock screen ? to light it up, then click ➕ "Add Lock".
4. The nearby lock will appear on the phone screen. Click ➕.
5. Rename the lock ✏️.
6. The lock is added successfully ✅.

TTLock users can register accounts using mobile numbers and emails, currently supporting 200 countries and regions worldwide. A verification code will be sent to the user's mobile phone or email, and registration is successful after verification.

6.3. Add locks

TTLock supports multiple lock device types. A lock must be added by the app after entering add mode. Generally, a lock that has not been added will enter add mode when the lock keyboard is touched. The default password is 123456 if not added by the phone.

6.4. User Management

6.4.1. Bluetooth Management

Ensure Bluetooth communication is stable. After connecting the phone to the door lock, click "?" to unlock (the phone must be within 5 meters of the door lock).

6.4.2. Setting Passcode

Passcodes are another unlocking method. After entering the passcode on the lock keyboard, press the unlock button in the lower right corner to unlock. Passcodes can be permanent, timed, one-time, custom, recurring, or erased. You can share passcodes via SMS, Email, Messenger, or WhatsApp.

6.4.3. Send e-Key

Click the "✉️" icon. You can send an e-Key to other TTLock users to authorize unlocking (the receiver must download the app and set up an account). Select the e-Key format (Timed, permanent, One-time, Recurring). Enter the recipient's TTLock account, set the name and effective time of the e-Key. You can choose to allow or disallow remote unlocking, and authorize as an administrator or not. The recipient's account will have Bluetooth unlock permission.

6.4.4. Add fingerprint

A fingerprint must be added first to be used for unlocking. The adding process requires the app to be near the lock. Fingerprint expiration data can be set as permanent, timed, or recurring. After setting, you can modify its validity period.

6.4.5. e-Key Management

Click the "✉️" icon. Managers can delete e-keys, reset e-keys, send, and adjust e-keys. They can also search lock records.

6.4.6. Passcode Management

Click the "?" icon. All generated passwords can be viewed and managed in the password management module. This includes password changes, deletions, resets, and unlock records.

6.4.7. Unlock Records

Click the "?" icon to query your unlock records.

6.5. Gateway Management (Optional)

The TT lock connects directly via Bluetooth, making it network-independent. The gateway acts as a bridge between smart locks and home Wi-Fi networks. Through the gateway, users can remotely view and calibrate the lock clock, read unlock records, and remotely delete or modify passwords.

6.5.1. Add Gateway

Follow the app instructions to add a gateway.

6.5.2. Manual Binding

After a short period, the app will show which locks are within the gateway's coverage. Once a lock is bound to the gateway, it can be managed through the gateway.

7. Reset the Lock

⚠️ Please note: All data will be erased if you reset your lock to factory defaults.

8. Replace Batteries

Please use 4 high-quality alkaline AA batteries ? for replacement when the battery is low.

9. 5V Emergency Power

The ? Micro USB interface is used to connect a regular 5V power bank to activate the lock in case the battery is dead ⚡. Note: The Micro USB interface is only for emergency unlocking and cannot be used for battery charging.

10. Emergency Key Unlock

The ? emergency key can be used when the battery is dead ⚡. Note: Keep at least one key outside your house so you can use it to unlock in case of emergency.

11. Anti-peep Keypad

The lock supports up to 16-digit Vague Code. Enter any 16-digit code; as long as a correct code is included within your input, you can open the door. ?️

12. Unlock From Outside

• Fingerprint: ? Place your finger on the fingerprint reader to unlock.
• User Code: ? Enter a 6-9 digit code and press to unlock. You would have set this unlock password in the app.
• Card: ? Swipe your card on the keypad of the lock to unlock.
• Mechanical key: ? Insert the key into the lock cylinder hole and rotate it 90 degrees counterclockwise.
• Smartphone: ? Use your smartphone to unlock. Please refer to the guide in the TTLock App.

13. FAQ

1) How to read operation records?

In the "Records" section on the main interface. ?

2) Why can't I unlock it after opening passage mode?

You need to perform an unlock verification using any method; then, the passage mode will take effect.

3) What is the purpose of Auto Lock?

You can set how long the lock remains unlocked after unlocking before it automatically locks again.

4) After installation, the touch sensing keyboard/screen has no response.

a) Check if the positive and negative electrodes of the battery are installed upside down, or if the battery has enough power ?.
b) Remove the back panel and check if the wires ? are connected properly.
c) To eliminate other issues, remove the lock and check if the wires of the lock body are squeezed. Re-wire if necessary.

5) Unable to register fingerprint.

Check fingers for dirt or wear. Check the fingerprint head on the lock for dirt and oil stains. Ensure the fingerprint sensor is working properly (press it to see if there is any response).

6) What is the reason why the smart lock consumes power quickly?

a) High standby power consumption.
b) Short circuit.

7) There is no response when pressing the handle on the outside of the door, but it unlocks normally from the inside, and the verification is normal, and the motor is normal.

It may be that the triangle direction on the clutch is incorrect. Please check and correct it.

8) How many times will the password be locked? How long is it locked?

Enter the wrong password more than 5 times in a row; the keyboard will be locked for 90 seconds.

FCC WARNING

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum 20cm distance between the radiator and your body. Use only the supplied antenna.

Guarantee ?

Customer Name:

Customer Calls:

Purchase Date:

Product Name:

Product Model:

Note:

1. Please keep this card so you can use it when you need warranty service.
2. Guangzhou LightSource Electronics Limited provides a one-year warranty from the date of purchase. This warranty service is valid for customers in any country in the world.