Aosu OutdoorCam D1 Lite HD Wi-Fi Security Camera

What's Included

• Camera
• Screw Pack
• Power Adapter
• Sticker
• Security Sticker
• Quick Start Guide

Product Overview

The OutdoorCam D1 Lite features:

• Antenna
• Spotlights
• Lens
• Microphone
• Status LED
• Infrared LEDs
• Micro SD Card Slot
• Reset button
• Speaker

Caution: Please insert the Micro SD Card according to the direction shown in the diagram. Incorrect insertion may cause the card to JAM and the device to be damaged.

SD Card Port: Supports Micro SD Card for local storage (Max 512GB).

Reset button: Press and hold for 3 seconds to prepare the device for connection.

Card capacity requirements: 8-512GB.

Read and write speed requirements: Class 10 level.

File format: FAT32.

Setting Up the System

Download the Aosu App from the App Store (iOS devices) or Google Play (Android devices).

Sign up for an Aosu App account, then follow the onscreen instructions to complete the setup.

Mounting the OutdoorCam

Find a Good Mounting Spot

To find a suitable spot for mounting the OutdoorCam D1 Lite, test the wireless signal strength:

1. Open the Aosu App, navigate to Camera Settings > Mounting Guide.
2. Take your camera and phone to the desired mounting location to test the wireless signal strength.
3. Move the camera as close to the Wi-Fi Router as possible for a better signal.

Select Height and Location

Hang the AOSUCam 7-10ft (78-118 inches) above the ground. This height maximizes the detection range of the motion sensor. Avoid placing the AOSUCam under direct sunlight.

The camera's field of view can extend up to 32ft. The motion detection zone is optimized at the recommended height.

Test the Wi-Fi signal at installation position

Use your cell phone to test the Wi-Fi signal quality at the installation position before installing the camera. Ensure the Wi-Fi router can provide a good Wi-Fi signal.

Installation

Follow these steps for installation:

1. Drill holes according to the positioning sticker using a 15/64" (6 mm) drill bit.
2. Insert the plugs.
3. Tighten the screws.

What is required:

• Power Drill (not provided)
• 15/64" (6mm) Drill Bit

Ensure the camera is securely mounted to the wall using expansion bolts and screws.

Notice

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The minimum separation distance is 20cm.

Declaration of Conformity

This product complies with the radio interference requirements of the European Community (CE).

Aosu declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the full declaration of conformity, visit https://www.aosulife.com.

This product can be used across EU member states.

Do not use the Device in extreme temperatures (too high or too low) or expose it to strong sunshine or wet environments. The suitable temperature range for the OutdoorCam and accessories is -20°C to 50°C.

RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, ensure a 20cm distance between the device and the human body during use.

For OutdoorCam: Wi-Fi Operating Frequency Range: 2412~2472MHz; Wifi Max Output Power: 17.13dBm(EIRP).

This product is designed and manufactured with high-quality materials and components that can be recycled and reused. ♻️

This symbol ?️ indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information on disposal and recycling, contact your local municipality, disposal service, or the retailer where the product was purchased.

Customer Service

Warranty

12-month limited warranty. The actual warranty period is implemented according to local laws and regulations.

Email Us

Customer Support: support@aosulife.com

Call Us

• United States: +1-866-905-9950 (Mon-Fri 9AM-5PM PST)
• United Kingdom: +44-20-3885-0830 (Mon-Fri 9AM-5PM GMT)
• Germany: +49-32-221094692 (Mon-Fri 9AM-5PM CET)
• Japan: +81-50-5840-2601 (Mon-Fri 9AM-5PM JST)

Social Media:

• Facebook: @aosulife ⓕ
• Twitter: @aosulife ⓣ
• YouTube: @aosulife ▶️