Comica EJoy D10 PRO RGB Dynamic Wireless Microphone

Introduction

Thank you for purchasing the Comica EJoy D10 Pro.

Key Features

• Innovative wired / 2.4GHz wireless mode, one-to-one and one-to-two options
• Cardioid polar pattern, large-diameter dynamic microphone capsule
• USB-C/XLR digital/analog output, wide compatibility
• 48kHz/24bit recording, built-in sound card, one-key Calmix® one-tap noise cancelling
• Supports 4-level gain adjustment and stepless monitoring volume control
• Real-time monitoring and mute
• Dynamic RGB lighting (6 modes available)
• 3 EQ modes for various acoustic styles
• Up to 45 hours of battery life in wireless mode
• Includes boom arm & desktop stand for flexible setup

Precautions

• When using XLR connection in wired mode to output analog audio signals, functions other than the dynamic microphone's audio signal (operation status indicator, EQ, gain adjustment, RGB light, real-time monitoring, etc.) cannot be used.
• The 1-to-1 set and 1-to-2 set are not compatible. The 1-to-1 set supports stereo monitoring, but the 1-to-2 set does not (both microphones output mono).
• When connecting to a computer, select "Comica_Eloy D10 Pro TX" as the input/output device in the sound settings.
• If the input volume is too high when connecting to a computer, you can adjust the gain in the "Microphone Properties - Levels" in the computer's sound settings. (Example shown for Windows system)
• To achieve excellent recording, point the microphone capsule towards the sound source.
• Do not use this product near heat sources or interference sources such as radiators, ovens, refrigerators, or air conditioners.
• This product is a high-precision instrument; avoid dropping, collision, or impact.
• Do not use this device in rain or humid environments, as it may cause short circuits.
• Store this product in a dry environment.
• The EJoy D10 Pro and EJoy D10 Pro COMBO have obtained certification in compliance with Article 38-24(1) of the Japanese Radio Law.

Package Contents

EJoy D10 Pro (A) (1-to-1 Set)

• Microphone (TX) *1
• Receiver (RX) *1
• Charging / Audio Output Cable *1
• Adapter USB-C to A *1
• Boom Arm *1
• Hook Ring * 5
• User Manual *1
• Warranty Card *1

EJoy D10 Pro (D) (1-to-1 Set)

• Microphone (TX) *1
• Receiver (RX) *1
• Charging / Audio Output Cable *1
• Adapter USB-C to A *1
• Desktop Microphone Stand *1
• User Manual *1
• Warranty Card *1

EJoy D10 Pro (A) COMBO (1-to-2 Set)

• Microphone (Transmitter/TX) *2
• Receiver (RX) *1
• Charging / Audio Output Cable *2
• Adapter USB-C to A *2
• Boom Arm *2
• Hook Ring * 10
• User Manual *1
• Warranty Card *1

EJoy D10 Pro (D) COMBO (1-to-2 Set)

• Microphone (Transmitter/TX) *2
• Receiver (RX) *1
• Charging / Audio Output Cable *2
• Adapter USB-C to A *2
• Desktop Microphone Stand *2
• User Manual *1
• Warranty Card *1

Product Structure and Parts Description

Microphone (TX)

• Dynamic Microphone Capsule
• Microphone Windscreen
• RGB Light Effect Area
• Status Indicator Light
• Monitoring Volume Knob / Mute Button
• Power / Noise Cancelling Button
• Gain Adjustment Switch
• EQ Effect Indicator Lamp
• 3.5mm Headphone Monitoring Terminal
• XLR Terminal
• EQ Effect Button
• RGB Light Effect Button
• USB-C Terminal
• Receiver Storage Slot

Detailed Description of Parts:

1. Dynamic Microphone Capsule
2. Microphone Windscreen
3. RGB Light: Features 6 RGB light effects: Audio Dynamic, Comica Orange, Ocean Wave, Colorful Breathing Light, RGB Slow Wave, and Rainbow Rotation. The light is red when muted.
4. Power / Noise Cancelling Button: Long press to turn power on/off; short press to toggle noise cancelling function on/off.
5. Status Indicator Light:
   • Noise Cancelling Status: Green light on
   • Mute Status: Red light on
   • Low Battery: Red light flashing
   • Charging (Power Off): Red light on
   • Charging Complete (Power Off): Blue light on
   • Not Paired: Blue light flashing slowly
   • Pairing Successful: Blue light on
6. Monitoring Volume Knob / Mute Button: Rotate clockwise for increased headphone volume; rotate counter-clockwise for decreased headphone volume. Short press to toggle mute function ON/OFF.
7. Gain Adjustment Switch: Slide left or right for 4-level gain adjustment.
8. EQ Effect Button: Long press to turn EQ function ON/OFF; short press to switch between 3 EQ presets.
9. EQ Effect Indicator Lamp:
   • Bass Boost: Orange
   • Natural: Blue
   • Bright: Green
   • Pairing: Blue light flashing rapidly
10. RGB Light Effect Button: Long press to turn light effects on/off; short press to switch between 6 light effects. Press and hold both the EQ Effect Button and RGB Light Effect Button simultaneously to enter pairing mode.
11. 3.5mm Headphone Monitor Terminal: Connect 3.5mm TRS/TRRS headphones for real-time monitoring. (If connecting to XLR devices, please provide your own XLR-XLR or XLR-3.5mm TRS audio cable).
12. USB-C Terminal: Use the charging/audio output cable to charge the microphone with a mobile power bank or DC power source, or connect to a device for digital audio output.
13. XLR Terminal: Analog audio can be output to devices such as sound cards, recorders, or mixing consoles via an XLR-XLR or XLR-3.5mm TRS audio cable.
14. Receiver Storage Slot: The receiver can be stored in the groove of the microphone stand.

Receiver (RX)

• USB-C Terminal
• USB-C Terminal: Connect to USB devices for digital audio output.

Installation and Use

Boom Arm Stand Installation

1. Clamp the base of the boom arm stand onto a desk and secure it by turning the screw underneath the base clockwise. ⇨ [Image showing clamp attachment]
2. Insert the boom arm stand into the base's socket and use the side screw on the base to fix or adjust the stand's angle. ⇨ [Image showing arm insertion and angle adjustment]
3. Connect the microphone's screw hole to the arm mount stand's screw and fix it by turning clockwise. ⇨ [Image showing microphone attachment to arm]
4. Use the tightening lock nut on the boom arm stand to adjust and fix the microphone's position. ⇨ [Image showing position adjustment]

Desktop Microphone Stand Installation

1. Connect the microphone's screw hole to the screw of the disc-shaped stand and fix it by turning clockwise. ⇨ [Image showing microphone attachment to desktop stand]
2. Use the tightening lock nut above the microphone to adjust the microphone's angle. ⇨ [Image showing angle adjustment]

How to Use

Wired Mode

1. Digital Output

Connect the microphone to a smartphone or computer via the audio output cable and select the monitor as needed. ⇨ [Diagram showing various device connections via USB-C and adapter]

• When combining with devices equipped with a Lightning port, please purchase a USB-Lightning adapter cable / adapter that supports OTG function.
• The microphone will automatically power on when connected to a device and will automatically shut down 10 minutes after disconnection.

2. Analog Output

Connect the microphone to an audio interface / recorder / mixer using an XLR-XLR or XLR-3.5mm TRS audio cable. ⇨ [Diagram showing XLR connections to audio equipment]

• When outputting analog audio through the XLR port in wired mode, all functions other than the transmission of dynamic audio signals are unavailable.
• When connecting to XLR interface devices, please provide your own XLR-XLR or XLR-3.5mm TRS audio cable.
• The microphone will automatically power on when connected to a device and will automatically power off after 10 minutes of inactivity after disconnection.

Wireless Mode

Pairing (The microphone and receiver are paired by default. If re-pairing is necessary, please refer to the pairing method below)

1. Turn on the microphone (TX), then long press the EQ Effect Button and RGB Light Button simultaneously.
2. Connect the receiver (RX) to the device to enable wireless mode. When pairing is successful, the status indicator light will remain blue. ⇨ [Diagram showing wireless pairing indicator]

• Before pairing, the status indicator light will flash blue slowly. During pairing, it will flash blue rapidly. After successful pairing, it will remain solid blue.
• If pairing fails with some smartphones (e.g., HUAWEI, OPPO), please check if the smartphone's OTG function is enabled (this function is enabled by default on most smartphones).

When connecting the receiver to a device, please refer to the connection methods below: ⇨ [Diagram showing various device connections via USB-C and adapter]

• When connecting to devices with a Lightning port, please prepare a USB C-Lightning adapter/cable that supports OTG function.

Specifications