Comica EJoy D10 RGB Unidirectional Dynamic Microphone User Manual

Introduction

Thank you for purchasing the Comica EJoy D10 microphone.

Main Features

• Unidirectional, large-diaphragm dynamic microphone capsule
• XLR/USB-C digital/analog dual output for wide compatibility
• 48kHz/24bit high-quality recording, built-in sound card & Calmix® one-tap noise canceling
• 4-step gain adjustment & continuously variable monitor volume control, real-time monitoring & mute function
• Dynamic RGB lighting (6 selectable modes)
• 3 EQ modes (supports various sound styles)
• Boom arm & desktop stand (flexible setup)

Precautions

Note: When outputting analog audio signals via XLR, functions other than the dynamic microphone's audio signal (operation status indicator, EQ, gain adjustment, RGB light, real-time monitoring, etc.) cannot be used.

Note: When connecting to a computer, select "Comica_EJoy D10" as the input/output device in the sound settings.

If the volume is too high when connecting to a computer, you can lower the gain by adjusting the "Microphone Properties - Levels" on your computer. (The following explains using the Windows system as an example)

For optimal recording, point the microphone capsule towards the sound source.

Do not use this product near heat sources or interference sources such as radiators, ovens, refrigerators, or air conditioners.

This product is a precision instrument; avoid dropping, collision, or impact.

Do not use this device in wet environments or during rain, as there is a risk of short circuits.

Store this product in a dry environment.

Package Contents

EJoy D10(A) Set

• Microphone *1
• 2-in-1 Audio Cable *1
• Boom Arm Stand *1
• Hook Ring *5
• User Manual *1
• Warranty Card *1

EJoy D10(D) Set

• Microphone *1
• 2-in-1 Audio Cable *1
• Desktop Stand *1
• User Manual *1
• Warranty Card *1

Product Structure and Parts Description

Microphone

• Dynamic Microphone Capsule
• Microphone Windscreen Sponge
• RGB Lighting Effect Area
• Status Indicator Lamp
• Monitor Volume Knob / Mute Button
• Gain Adjustment Switch
• EQ Effect Indicator Lamp
• 3.5mm Headphone Monitoring Jack
• XLR Jack
• Noise Canceling Button
• EQ Effect Button
• RGB Lighting Effect Button
• USB-C Jack

1. Dynamic Microphone Capsule

2. Microphone Windscreen Sponge

3. RGB Lighting Effect Area: There are 6 types of RGB lighting effects: Audio Dynamic/Comica Orange/Wave/Color Breathing Light/RGB Slow Wave/Rotating Rainbow. In mute status, the red indicator light will remain lit.

4. Noise Canceling Button: Short press to switch noise canceling ON/OFF.

5. Status Indicator Lamp:

• Normal Operation: Solid blue light
• Noise Canceling Active: Solid green light
• Mute Status: Solid red light

6. Monitor Volume Knob / Mute Button: Turn clockwise to increase headphone volume, counter-clockwise to decrease headphone volume; short press to toggle mute function ON/OFF.

7. Gain Adjustment Switch: Slide left or right for 4-step gain adjustment.

8. EQ Effect Button: Long press to turn EQ function ON/OFF; short press to switch between 3 EQ presets.

9. EQ Effect Indicator Lamp:

• Bass Boost: Orange
• Natural: Blue
• Bright: Green

10. RGB Lighting Effect Button: Long press to turn lighting effects ON/OFF. Short press to cycle through 6 lighting effects.

11. 3.5mm Headphone Monitoring Jack: Connect 3.5mm TRS/TRRS headphones to monitor in real-time.

12. USB-C Jack: Output digital audio to devices via the 2-in-1 audio connection cable.

13. XLR Jack: Output analog audio to sound cards, recorders, mixing consoles, and other equipment via an XLR-XLR or XLR-3.5mm TRS audio cable. (If connecting to XLR devices, please provide your own XLR-XLR or XLR-3.5mm TRS audio cable.)

Setup and Usage

Boom Arm Stand Setup

1. Clamp the base of the boom arm stand onto the desk and secure it by turning the screw at the bottom of the base clockwise.
2. Insert the boom arm stand into the base slot and use the side screw on the base to fix or adjust the angle of the stand.
3. Connect the microphone's screw hole to the screw on the arm mount stand and secure it by turning clockwise.
4. Use the locking nut on the boom arm stand to adjust and fix the microphone's position.

Desktop Microphone Stand Setup

1. Connect the microphone's screw hole to the screw on the disc-shaped stand and secure it by turning clockwise.
2. Use the locking nut on the microphone to adjust the microphone's angle.

Usage

1. Digital Output

Connect the microphone to your smartphone or computer via the 2-in-1 audio cable and select the monitor as needed.

Note: When combining with devices that have a Lightning port, please purchase a USB-Lightning adapter cable / adapter that supports OTG function separately.

Note: The microphone will automatically power on when connected to a device and automatically shut down when disconnected from the device.

2. Analog Output

Connect the microphone to an audio interface / recorder / mixer using an XLR-XLR or XLR-3.5mm TRS audio cable.

Note: When outputting analog audio via the wired mode XLR port, all functions other than dynamic audio signal transmission are not available.

Note: When connecting to XLR interface devices, please provide your own XLR-XLR or XLR-3.5mm TRS audio cable.

Note: The microphone will automatically power on when connected to a device and automatically power off when disconnected from the device.

Product Specifications