Keychron M6 Wireless Mouse User Manual

Product Overview

This document provides instructions and specifications for the Keychron M6 Wireless Mouse.

Product Identification

The Keychron M6 Wireless Mouse features the following components:

• 1. Left button
• 2. Right button
• 3. Infinite wheel
• 4. Wheel mode shift
• 5. DPI button
• 6. Bluetooth channel shift
• 7. Mode toggle
• 8. Report rate button
• 9. Side scroll wheel
• 10. Mouse indicator
• 11. Forward button
• 12. Backward button
• 13. 2.4GHz Type-A receiver
• 14. 2.4GHz Type-C receiver

Connection Modes

Wired Mode

When the mode switch is in the "OFF" position, the mouse will not respond if the cable is not connected. Connect the Type-C cable to the mouse and the USB port on your device. The mouse is ready to use when the indicator lights up. When connected by cable, the mode defaults to wired mode, even if the toggle is set to Bluetooth or 2.4GHz mode.

2.4GHz Mode

1. Switch to "G" mode (2.4GHz mode). The mouse will automatically enter 2.4GHz pairing mode, and the indicator will slowly flash green.
2. Connect the 2.4GHz receiver to the device's USB/Type-C port. Upon successful connection, the indicator will turn green and stay on for 3 seconds before dimming off. The mouse is now ready for use.
3. In 2.4GHz pairing mode, the indicator will slowly blink green for 3 minutes. If not connected within 3 minutes, the indicator will turn off. To reconnect, hold both the "Left button + Forward button" for 4 seconds to re-enter pairing mode.
4. To repair the connection in 2.4GHz mode, unplug the receiver first. Then, hold both the "Left button + Forward button" for 4 seconds, wait for the green light to start flashing, and plug the receiver back in to complete the pairing process.

Note: For the best wireless experience, it is recommended to use the extension adapter for the receiver and place it close to the mouse for lower latency and fewer signal interferences.

Bluetooth Mode

1. Switch to "B" mode (Bluetooth). The mouse will automatically enter Bluetooth pairing mode, and the indicator will slowly flash blue.
2. Open your device's Bluetooth settings, search for "Keychron M6", and click "connect" to complete pairing.
3. In Bluetooth pairing mode, the indicator will slowly blink blue for 3 minutes. If not connected within 3 minutes, the indicator will turn off. To reconnect, hold both the "Left button + Forward button" for 4 seconds to re-enter pairing mode. The indicator will slowly blink blue.
4. To pair with a new device in Bluetooth mode, hold both the "Left button + Forward button" for 4 seconds. The indicator will slowly blink blue, indicating that Bluetooth has re-entered pairing mode. You can then connect the new device to the M6.
5. The Bluetooth mode supports three channels, allowing seamless switching between three devices.

Status Indicators

2.4GHz Mode Indicator

• Slowly blinking green: Ready to be paired.
• Quickly blinking green: Pairing with the previous device.

Bluetooth Mode Indicator

• Slowly blinking blue: Ready to be paired.
• Quickly blinking blue: Pairing with the previous device.

Low Power Indicator

• Slowly blinking red: Low battery.

DPI Indicator

• White light: 400 DPI
• Green light: 800 DPI
• Blue light: 1600 DPI (default)
• Orange light: 3200 DPI
• Red light: 5000 DPI

Report Rate Indicator

• White light: 125Hz (Default in Bluetooth mode)
• Blue light: 500Hz
• Red light: 1000Hz (Default in wired & 2.4GHz mode)

How to Factory Reset

Hold down both the "DPI" button and "Report Rate" button for 4 seconds. All LED lights on the mouse will blink three times to indicate a successful factory reset.

Auto-Sleep Mode

The mouse will enter Auto-Sleep mode after 10 minutes of inactivity in 2.4GHz or Bluetooth mode to save battery. It will not activate in wired mode. Move or click the mouse to wake it up.

Driver Software

The Keychron M6 mouse driver can be downloaded from www.keychron.com. If the driver software cannot connect to the mouse, please contact Keychron for technical support.

Charging Indicator Explanation

• Fully Charged: The mouse indicator will stay GREEN.
• Low Power: The mouse indicator will slowly blink RED.

The mouse is compatible with all USB ports. For optimal signal and charging speed, connecting to a USB 3.0 port is recommended. When charging via the Type-C cable without pairing, the indicator stays RED while charging and turns GREEN when fully charged.

Note: The product supports up to 5V charging voltage and 300 mA charging current. Keychron is not responsible for any issues caused by improper recharging.

What's in the Box

• Mouse x 1
• Type-C receiver x 1
• Extension Adapter x 1
• User manual x 1
• Type-C to Type-C cable x 1
• Type-A receiver x 1
• Type-A to Type-C adapter x 1

Mouse Specifications

• Size: 122.5*75.4*50mm
• Weight: 78 ± 3g
• Report Rate (polling rate): 125Hz (White) - 500Hz (Blue) - 1000Hz (Red)
• Sensor: PixArt 3395
• Resolution: 100 - 26000 DPI
• Mouse micro switches: Huano Micro Switch (80 million clicks life time)
• 2.4GHz / Bluetooth connection range: Approx 10m of open space
• Battery capacity: 800mAh
• Usage duration: 80 Hours
• Recharge time: 2 Hours
• Charging port: Type-C
• Connection mode: 2.4GHz - Bluetooth - Wired
• Device name: Keychron M6

Contact Information

Keychron, Inc.
Dover, DE 19901, United States

Find us at:

• https://www.keychron.com
• Support@keychron.com
• Facebook: @keychron
• Instagram: @keychron
• Twitter: @keychronMK

Designed by Keychron
Made in China

China General Agent: Kexin Technology (Shenzhen) Co., Ltd.
Implementation Standard: GB 4943.1-2022
After-sales Hotline: 400-0766268
Address: Room 201, Building 2, Wenkeng Industrial Zone, Dafu Road 24, Bantian Street, Longgang District, Shenzhen

FCC Compliance Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.