MOUNTUP TV Wall Mount Installation Instruction

Safety Caution

Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact MOUNTUP.

• This product is designed for use in wood stud or solid concrete wall.
• DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and mount combined.
• Incorrect installation may result in product damage, property damage, or body injury. MOUNTUP shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact MOUNTUP customer service team. Never use damaged parts!

Must Check Before Getting Started

VESA Minimum Pattern (W × H): 150mm x 100mm / 6 in x 4 in

VESA Maximum Pattern (W × H): 800mm x 400mm / 32 in x 16 in

Product Dimensions:

• Max Width: 800mm/32"
• Min Width: 150mm/6"
• Max Height: 400mm/16"
• Min Height: 100mm/4"
• Depth: 88mm/3.46"
• Wall Plate Width: 82mm/3.23"

Load Capacity: MAX: 120 lbs (54.5 kg)

DO NOT exceed the maximum weight indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage or injury.

Supplied Parts and Hardware

Wall Plate: H x2

Wall Plate Cover: K x1

TV Brackets: J x1

Allen Key: G x1

Lag Bolt: ST8x65mm, A x6

Washer: Φ8mm, B x6

Bolt: M6x12mm, D x2

Washer: Φ6mm, E x2

Nut: M6, F x2

Spacers: H10mm x4, H5mm x4

Philips Screws: M4-5-6 (M4 x 12mm x4, M4 x 30mm x4)

Philips Screws: M6 x 15mm x4, M6 x 30mm x4

Philips Screws: M8 x 25mm x4, M8 x 45mm x4

Washers: Φ6mm x8

Bubble Level: T1 x1

Velcro Cable Ties: T2 x3

NOTE: Not all parts and hardware included will be used.

Extra Tools You Need (Not Supplied)

For Wood Studs: Stud Finder, Pencil, Screwdriver, Socket Wrench (S10mm)

For Concrete Wall: Hammer, Masonry Drill Bit (Φ7/32" or Φ5.5mm for pilot holes, Φ3/8" or Φ10mm for anchors), Electrodrill

General: Band Tape

CAUTION: Do not tighten the screws excessively or tighten them by using the Electrodrill, or your TV might be damaged.

1 Attach Brackets to TV

1-1 Select Correct TV Screw Diameter: Use M8, M6, or M4 screws as appropriate for your TV.

1-2 Select Correct TV Screw Length: Choose screws that are not too short (will not hold) and not too long (will damage TV). Use spacers and washers if necessary for uneven surfaces or recessed backs.

Which Situation Needs Spacers?

• For more spacing between bracket and TV.
• For raised back TV.
• For counterbore of TV.

1-3 Hardware for Brackets:

• Use Philips Screws (M4-5-6) and Spacers/Washers as needed.
• Ensure screws are not more than 5/8" (16mm) into the TV's mounting holes.

2 Assemble Wall Plate

2-1 Assemble two Wall Plates (H) with Bolts (D), Washers (E) and Nuts (F). Keep the upside of the two Wall Plates (H) horizontal, and then use Wrench (G) to fasten the Nuts (F).

2-2 Buckle the Wall Plate Cover (K) on the Wall Plate (H).

3 Attach Wall Plate to Wall

OPTION A: Wood Stud Installation

A-1 Locate Studs: Verify and mark the center of the stud. Line up the wall plate holes with your stud center line. Level the wall plate and mark pilot hole locations. Ensure the drywall covering does not exceed 5/8 in. (16 mm). Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm), actual 1 ½ x 3 1/2 in. (38 x 89 mm).

A-2 Drill Pilot Holes: Drill pilot holes using a Φ7/32 in (Φ5.5mm) diameter drill bit into the center of the stud.

A-3 Install Wall Plate: Use lag bolts (A) and washers (B) with Socket Wrench. DO NOT use Electrodrill. Ensure all 4 lag bolts (A) are firmly tightened.

CAUTION: Avoid potential personal injuries and property damage! Ensure the wall plate assembly is securely fastened to the wall before continuing.

OPTION B: Solid Concrete Wall Installation

B-1 Mark Locations: Level the wall plate and mark the pilot hole locations. Note: 4 bolts for the upside & 2 for downside.

B-2 Drill Pilot Holes: Drill pilot holes using a Φ3/8 in (Φ10mm) diameter drill bit. Never drill into the mortar between blocks.

B-3 Install Wall Plate: Use hammer to knock anchors (not included) into the concrete wall until flush. Install wall plate using lag bolts (A) and washers (B) with Socket Wrench. DO NOT use Electrodrill. Ensure all 6 lag bolts (A) are firmly tightened.

CAUTION: Avoid potential personal injuries and property damage! Ensure the wall plate assembly is securely fastened to the wall before continuing.

4 Hang and Secure TV to Wall Plate

4-1 Wall Plate Installation Integrity Test: Before hanging the TV, conduct this test.

4-2 Hang and Secure TV: TV must be hung by two people. Hang the TV assembly onto the wall plate. Ensure the TV brackets are in the locked position so the TV is securely attached to the wall plate assembly.

CAUTION: Avoid potential personal injury or property damage! Always make sure your TV brackets are in the locked position.

If necessary, Take down the TV from the Mount: TV must be taken down by two people. To prevent breaking the locking latch, always pull and hold the release straps down while pulling the TV away from the wall.

5 Adjustments

5-1 Tilt Adjustment: Loosen the 2 tilting bolts, pull the brackets to your desired angle (+10° to -15°), then fasten the 2 tilting bolts.

5-2 Leveling Adjustment:

• To keep the TV in a vertical position, use two M4 screws (MA) to insert the holes on the two brackets respectively.
• Turn the screw on the lower bracket clockwise until the TV is level. (Maximum leveling adjustment 15mm)