Infinity X1 Under-Cabinet Lights

Step 1: Magnetic Mounting

Align the magnets located on the back of the wall light to attract the metal plate. [Diagram description: A light fixture with magnets on the back aligning to a metal plate.]

Step 2: Attaching the Metal Plate

The metal plate can be fixed on a smooth surface with the included 3M sticker. Peel one side of the 3M sticker and press firmly. [Diagram description: A metal plate with 3M adhesive backing.]

Step 3: Mounting the Lights

Install the Under-Cabinet Lights on the wall or desired location. [Diagram description: Under-cabinet lights mounted on a surface.]

Step 4: Remote Control Placement

Place the circular metal piece on the remote's back, peel one side of the 3M sticker, and attach it near the Under-Cabinet Lights. [Diagram description: A remote control with a metal disc on its back.]

Power On/Off

Press the GREY button on each light to turn them ON or OFF.

Dimming

Long-press the power button for dimming.

Charging

The remote uses USB-C for charging. The indicator light is red when charging and turns green when the unit is fully charged. ?

MODE ALL

Activates Zone 1 and Zone 2.

MODE 1

Activates Zone 1 Only.

MODE 2

Activates Zone 2 Only.

[Diagram description: Three modes shown with buttons for ZONE 1 and ZONE 2.]

Color Temperature Adjustment

Click to adjust color temperature.

Dimming

Long-press for dimming.

Zone Selection

Cycle through OFF, Zone 1, Zone 2.

Setting up a Group of Lights

1. Select Zone 1 or Zone 2.
2. On each light you want in the same group, press and hold the power button for 3 seconds. Lights will fade on and off to show they are pairing.
3. When pairing is complete, the light will remain constant.
4. Repeat for each light in the group.

Resetting a Light to Original Factory Code

1. Set the remote Zone to OFF.
2. Press and hold the power button for 15 seconds.

General Warnings

CAUTION: Battery not replaceable. Do not disassemble. This is not a toy and is not intended for use by children. For adult use only. Never look directly into the light or shine the light into another person's eyes when it is illuminated.

Do not disassemble the housing. There are no internal serviceable parts.

This unit contains a rechargeable battery. Although this product arrives partially charged from the factory, it MUST be fully charged before the first use.

Rechargeable Batteries

Do not dismantle or open devices to access built-in rechargeable batteries. In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact occurs, wash the affected area with copious amounts of water and seek medical advice. The battery needs to be charged before use.

FCC and Compliance Statements

WARNING: Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help.

FCC Statement of Compliance: Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-005 (B)/NMB-005 (B). This Class B digital apparatus complies with Canadian ICES-005.

Precautions

Please store and use this product at room temperature.

Do not expose this product to rain or damp surroundings.

Do not disassemble, repair, or modify this product on your own.

To avoid any risk, do not dispose of this product inappropriately or expose it to fire, as there is a built-in, non-replaceable lithium battery.

Indoor Use

For Indoor Use Only.

Please dispose of batteries according to local regulations for the battery chemistry. Working Temperature: -20 °C to 54 °C (-4 °F to 129.2 °F).

Battery and Waste Battery Information

All persons have a responsibility to properly dispose of batteries.

Separate batteries from household garbage. Never place batteries in curbside collection carts as they can overheat, explode, and cause fires.

Batteries can be dropped off at designated battery disposal facilities. Search online for local collection sites that accept rechargeable batteries.

Handle batteries with care. Keep out of reach of children. Keep batteries away from combustible materials. Avoid storing batteries at extreme temperatures. Do not dispose of in fire or heat. Do not puncture, damage, or disassemble. Do not mix old and new batteries.

The battery is an ICR 4025180, 22000mAh, 3.7V (ICR stands for "Li-Co" or "Lithium Cobalt" batteries). The recycling symbols on the battery indicate they must be recycled, not thrown away.

This battery contains toxic materials that can harm ecosystems if released. When disposed of in landfills, these materials can enter the local groundwater system and propagate through the food chain in various ways, causing damage to the environment.