Olight Warrior X3 User Manual

In the Box

• Warrior X3 (with Battery and Warrior Ring)
• USB Magnetic Charging Cable (MCC3)
• Holster
• Silicone Tactical Grip Ring (TGR)

Specifications

Model: Warrior X3

Output: HIGH: 2,500 lumens (2.5 min, then 40% for 129 min, then 12% for 13 min); LOW: 300 lumens (8h)

Beam Distance: 560m

Candela: 78,000cd

Waterproof: IPX8

Drop Resistance: 2m

Dimensions: Length: 149.5mm (5.89in), Diameter: 39mm (1.54in)

Weight: 255g (8.99oz) (Including Battery and Warrior Ring)

Note: All specifications are based on ANSI/NEMA FL1-2009 Standard. Tests were performed indoors at 25°C with no wind. Runtime may vary based on external temperature and ventilation. Maximum output brightness decreases as battery voltage decreases.

Product Overview

The Warrior X3 features a magnetic tailcap with a tail switch, a body, a head, and a tactical grip ring. An insulating film is located within the battery compartment before first use.

Charging

Charging Cable: USB Magnetic Charging Cable (MCC3)

Input: USB Type A to magnetic charging connector, 0.5m length. USB A input: DC 5V 2A.

Charging Pattern: CC&CV (Constant Current & Constant Voltage)

Maximum Charging Current: 2A

Voltage of Fully Charged Battery: 4.2V ± 0.05V

Charge Indication: Red light indicates charging; Green light indicates charging is complete (battery level >95%) or the cable is disconnected.

Time to Fully Charge: Approximately 5.5 hours (when using a sufficient USB power source).

Instructions:

• Before first use, ensure the product is fully charged.
• Connect the USB end of the magnetic charging cable to an external USB power source.
• Attach the magnetic charging connector to the flashlight's magnetic charging port.
• Only use the standard MCC3 charging cable; it is not compatible with other MCC versions.

Battery Installation

Before the first use, unscrew the tailcap and remove the insulating film from the battery compartment. Then, screw the tailcap back on tightly.

When replacing the battery, ensure the positive (+) end of the new battery faces the flashlight head.

Available Battery: 1 x customized 5000mAh 21700 rechargeable lithium-ion battery.

Vibrating Power Indicator

The flashlight provides a vibrating alert for low battery levels:

• When battery power is 20% or less: vibrates once every 5 minutes.
• When battery power is 10% or less: vibrates once per minute.
• When battery power is 5% or less: vibrates once every 10 seconds.

TGR (Tactical Grip Ring) Installation

1. Unscrew the tailcap and remove the original Warrior Ring.
2. Install the silicone TGR onto the flashlight body.
3. Tighten the tailcap securely.

How to Operate

The flashlight is operated via the tail switch:

• Low Light Output: Lightly press the tail switch.
• High Light Output: Press the tail switch firmly (all the way down).
• Turn On/Off: Perform a single click (press and quickly release) on the tail switch.
• Momentary Mode: Press and hold the tail switch; the light will remain on as long as the switch is held. Release the switch to turn the light off.

Important Safety Information

DANGER

Do not shine the light directly into human eyes. This may cause temporary blindness or permanent eye damage.

WARNING

• Keep out of reach of children.
• If the product is left unused or is being transported, loosen the tailcap by half a turn to prevent accidental activation.
• Handle batteries with care. If a battery is removed, take care of it and do not mix it with conductive metals.
• Do not cover the flashlight's head or place the head on the ground when the flashlight is on. The heat generated may damage the flashlight or cause nearby flammable objects to burn.
• Do not use non-protected rechargeable batteries.
• Do not use a battery if its casing is broken.
• Do not remove the battery from the flashlight for charging.

NOTICE

• Avoid short-circuiting the tail switch cap with the surrounding ring. A short circuit can result in a weak electric discharge and may lead to complete battery drain if left in this state for too long.
• Do not activate high mode repeatedly under high temperature conditions to prevent the flashlight body from overheating and causing discomfort to the user's hand.
• The tail switch may not function correctly when immersed in seawater or other conductive media. Please keep it clean and dry.
• The magnetic tail switch cap is prone to attracting iron debris. Please keep the tail switch cap and the surrounding ring clean.

Exclusion Clause

Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in this manual.

Warranty Information

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 5 years of purchase: Contact Olight for repair or replacement.
• Battery Warranty: Olight offers a one-year warranty for all rechargeable batteries.
• MCC Magnetic USB Charging Cable: One-year warranty.
• Other fittings (e.g., lanyard, clip): Contact customer service within 30 days of purchase if there is a quality defect or damage under normal use conditions. Conditional quality assurance will be provided for damage under abnormal use conditions or after 30 days.

Support & Declarations

USA Customer Support: cs@olightstore.com

Global Customer Support: customer-service@olightworld.com

Visit www.olightworld.com to see Olight's complete product line of portable illumination tools.

EU Declaration of Conformity: Can be found at https://olightworld.com/ec-declaration

Company Information

Dongguan Olight E-Commerce Technology Co., Ltd

4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China

Certifications: CE, RoHS, UKCA

Manufacturing/Revision Date: A.10.31.2021