Bose Panaray Full-Range-Driver Array Loudspeakers: Installation Guide

Introduction

Panaray sound-reinforcement loudspeakers feature full-range cone transducers in proprietary array configurations that provide exceptional reliability in adverse conditions, while delivering natural vocal clarity. For more than five decades, Bose has been improving the performance of full-range cone transducers to provide unmatched reliability, natural sound quality, and wide coverage patterns. Available in both point-source and column line array acoustic designs, Panaray loudspeakers cover a wide variety of installed-sound venues, for indoor or outdoor locations.

Panaray 802 Series IV

The 802 Series IV loudspeaker, now in its 4th generation, features 8 full-range drivers arranged in a proprietary Articulated Array® design, delivering extension down to 52 Hz and natural vocal clarity – all in a small, lightweight, and weather-resistant enclosure.

• 8 x 4.5-inch full-range cone drivers
• 52–15 kHz frequency range
• 120° H x 100° V coverage pattern
• 123 dB maximum peak SPL
• Indoor/Outdoor use

Diagram Description: Image showing the Bose 802 Series IV loudspeaker.

Panaray 402 Series IV

The compact enclosure of the 402 Series IV contains 4 full-range drivers arrayed for increased vertical coverage control. Compared to the 802, the 402 delivers similar output level, but with tighter vertical coverage and less low-frequency response. For smaller venues requiring a high-value solution, a single 402 is capable of covering an entire listening area for accurate speech and music reproduction.

• 4 x 4.5-inch full-range cone drivers
• 73–15 kHz frequency range
• 120° H x 60° V coverage pattern
• 119 dB maximum peak SPL
• Indoor/Outdoor use

Diagram Description: Image showing the Bose 402 Series IV loudspeaker.

Panaray 502A

The Panaray 502 A features 5 full-range drivers that deliver the most consistent coverage pattern versus frequency within the Panaray line. The slightly curved, narrow enclosure has an elegant design that blends with any decor. For speech program material, a single loudspeaker can cover smaller venues. Use with full-range music program requires additional subwoofers.

• 5 x 4.5-inch full-range cone drivers
• 103–15 kHz frequency range
• 120° H x 70° V coverage pattern
• 117 dB maximum peak SPL
• Indoor use only

Diagram Description: Image showing the Bose 502A loudspeaker.

CAUTION: These loudspeakers are intended for installation by professional installers only.

Dimensions

Panaray 802 Series IV Loudspeaker Dimensions

Diagram Description: Top, Front, Right, Back, and Bottom views of the 802 Series IV loudspeaker with detailed dimensions in mm and inches. Key mounting points are indicated with M8 threaded inserts.

Panaray 402 Series IV Loudspeaker Dimensions

Diagram Description: Top, Left, Front, Right, Back, and Bottom views of the 402 Series IV loudspeaker with detailed dimensions in mm and inches. Key mounting points are indicated with M8 threaded inserts.

Panaray 502A Loudspeaker Dimensions

Diagram Description: Top, Back, and Left views of the 502A loudspeaker with detailed dimensions in mm and inches. Key mounting points are indicated with M8 threaded inserts.

Installation

Important Safety Instructions:

• These loudspeakers are intended for installation by professional installers only.
• All Bose products must be used in accordance with local, state, federal, and industry regulations.
• Unsafe mounting or overhead suspension of any heavy load can result in serious injury and equipment damage. Installers must evaluate the reliability of any mounting method.
• Prior to overhead installation, a licensed professional engineer must approve the location and attachment method, ensuring compliance with building codes and regulations. The mounting surface must support the total system weight with a 10:1 safety factor.
• Use components from reputable manufacturers. Bose recommends its own mounting accessories. Custom hardware requires review by a licensed professional engineer.
• Bose Panaray loudspeakers feature integrated M8 threaded inserts. Use only metric hardware (Class 8.8 or equivalent). Do NOT use SAE 5/16" hardware.
• Use lock washers or locking compound for vibration resistance.
• Tighten fasteners to specified torque; over-tightening can cause damage.
• Do not alter threaded attachment points.
• Use a safety cable, separately attached to the cabinet, at a point not common with load-bearing attachment points. Consult a professional for design and installation.

CAUTION: Installed loudspeakers require regular inspection and maintenance. Inspect mounting hardware for corrosion or damage and replace as needed.

CAUTION: Do not modify loudspeakers or mounting accessories, as this may compromise safety and result in damage, injury, or death.

This product conforms to all applicable EU directive requirements. Declaration of conformity available at www.Bose.com/compliance.

Panaray 802 Series IV Loudspeaker Mounting Options

Panaray 802 Series IV Loudspeaker U-bracket (Indoor or Outdoor Use)

The 802 Series IV loudspeaker can be mounted on a wall or ceiling using the U-bracket accessory kit (not included). Recommended Tools: 5 mm Allen wrench.

802 Series IV loudspeakers weigh 13.6 kg (30 lb). Use caution when lifting. Do not rest loudspeakers on their grilles.

1. Choose a mounting location that will safely support the loudspeaker's weight (13.6 kg / 30 lb). Refer to "Guidelines for permanent installation" on page 3. Ensure the mounting surface and method are structurally sound (10:1 safety weight ratio recommended).
2. Hold the U-bracket in the mounting location and mark the holes.
3. Drill four holes and mount the bracket using all four screws.
4. Remove the backing from the foam tape and attach a bracket spacer to each side of the loudspeaker. Insert an M8 cap screw into the front hole on each side (do not tighten).
5. Place the loudspeaker on the bracket.
6. Tilt the loudspeaker to the desired angle and insert the second M8 cap screw on each side.
7. Using a 5 mm Allen wrench, tighten all four cap screws to 5.6 Nm (50 in-lb).
8. Connect field wiring and test loudspeaker operation.

Diagram Description: Illustrates the U-bracket mounting process for the 802 Series IV, including marking holes, drilling, attaching spacers, inserting screws, and tightening. Also shows wall and ceiling mount pitch angle adjustments.

SB-8 Suspension Bracket (Indoor Use Only)

The SB-8 suspension bracket kit is used for suspension-mounting one 802 loudspeaker. The kit provides 0-45 deg pitch adjustment.

Diagram Description: Shows the SB-8 suspension bracket and its attachment to the 802 loudspeaker for suspension mounting.

WBP-8 Wall Bracket (Indoor Use Only)

Diagram Description: Illustrates the WBP-8 wall bracket for mounting the 802 loudspeaker at a 45° angle.

Panaray 402 Series IV Loudspeaker Mounting Options

RMUBRKT1 Pan-and-Tilt Bracket Kit (Indoor Use Only)

The RMUBRKT1 pan-and-tilt bracket is intended for indoor use only. For outdoor applications, use the WBPWR-50 pan-and-tilt bracket.

Hardware included: M8 x 20 mm screws (4) for 402 loudspeakers, M8 x 45 mm screws (4) for other loudspeakers, Flat washers (4).

1. Remove the lower carriage bolt and separate the front and rear halves of the bracket.
2. Attach the bracket to the wall. Follow the instructions provided with the wall bracket. Choose a position and mounting method consistent with local building codes and regulations. Ensure the mounting surface and method are structurally capable of supporting the loudspeaker's weight (7.3 kg / 16 lb). A 10:1 safety weight ratio is recommended.
3. Using the included T3 square drive, remove plastic inserts on the rear panel of the loudspeaker and attach the bracket using only the included M8 x 20 mm screws (torque: 13.6–16.3 Nm / 10–12 ft-lb).
4. Hang the loudspeaker on the wall-mounted half of the bracket and install the lower carriage bolt removed earlier.
5. Adjust the pitch and yaw using the specified tightening torque (e.g., 11 Nm for pitch, 9 Nm or 25 Nm for yaw).

Diagram Description: Shows the RMUBRKT1 bracket assembly, wall attachment, loudspeaker connection, and pitch/yaw adjustment points with torque specifications. Also includes a note about rotating the speaker plate 90 degrees for horizontal mounting.

SB-4 Suspension Bracket Kit (Indoor Use Only)

Attach the bracket to the rear of the 402® loudspeaker. Choose a position and mounting method consistent with local building codes and regulations.

Hardware: M8 x 16 mm screws (2), M8 screws (2).

Diagram Description: Illustrates the SB-4 suspension bracket attachment to the rear of the 402 loudspeaker, showing screw types and torque specifications (2.3–2.8 Nm / 20–25 in-lb). Also shows angle adjustments (0-45 degrees).

Panaray 502A Loudspeaker Mounting Options

WCB-5 U-bracket Kit (Indoor Use Only)

Hardware: M8 x 12 mm screws (3), M5 x 10 mm screws (5), M8 x 20 mm screws (2).

1. Choose a mounting location that will safely support the loudspeaker's weight (6.8 kg / 15 lb). Refer to "Guidelines for permanent installation" on page 3. Ensure the mounting surface and method are structurally capable (10:1 safety weight ratio recommended).
2. Hold the U-bracket in the mounting location to mark and drill holes. Use at least three (3) of the five (5) holes in the center vertical row for wall attachment. Ensure the top center hole is used when mounting vertically.
3. Remove end screws and mount the lock bracket.
4. Attach the 502A loudspeaker to the U-bracket. Rotate the loudspeaker to the desired angle and insert the thumbscrew into the locking bracket.
5. Ensure the safety cable is installed.

Diagram Description: Shows the WCB-5 U-bracket, hardware, wall attachment, loudspeaker connection with thumbscrew, and safety cable installation. Includes torque specification for M8 x 12 mm screws (2.3–2.8 Nm / 20–15 in-lb).

WBP-5 Wall-Mount Kit (Indoor Use Only)

Hardware: M8 x 25 mm, M6 x 25 mm, M8 x 16 mm (5), M5 x 10 mm.

1. Choose a mounting location that will safely support the loudspeaker's weight (6.8 kg / 15 lb). Refer to "Guidelines for permanent installation" on page 3. Ensure the mounting surface and method are structurally capable (10:1 safety weight ratio recommended).
2. Remove both screws from the bracket and separate the two pieces.
3. Hold the wall bracket in the mounting location to mark and drill holes. Use four (4) screws per bracket to attach it to the wall. The loudspeaker can be mounted vertically on a wall (A), angled down from a ceiling (B), or angled out from a wall (C).
4. Mount the speaker plate on the 502A loudspeaker using four M8 x 16 mm screws (torque: 2.3–2.8 Nm / 20–25 in-lb). Rotate speaker plate 180° to mount as shown in Step 3A.
5. Mount the loudspeaker on the wall plate. Slide the fin of the speaker bracket into the wall bracket and install the M8 x 25 mm pivot screw, and then the M6 x 25 mm pitch locking screw.
6. Set the pitch and yaw of the loudspeaker. To set pitch: Loosen M8 x 25 mm screw, remove M6 x 25 mm screw, change angle, re-insert M6 screw, tighten both. To set yaw: Loosen both screws, change angle, tighten both.
7. Using an M8 x 16 mm screw, attach the safety cable to the speaker. Ensure the safety cable is attached to the wall independent of the wall plate.

Diagram Description: Illustrates the WBP-5 wall-mount kit, hardware, wall attachment options (vertical, ceiling angle, wall angle), speaker plate mounting, loudspeaker connection, pitch/yaw adjustment, and safety cable attachment.

CVT-5 Transformer Kit (Indoor Use Only)

Mention of the CVT-5 transformer kit for use with 502A loudspeakers.

CSB-5A Suspension Bracket Kit (for indoor use only)

Hardware: M8 x 1.25 x 12 mm (3).

Diagram Description: Shows the CSB-5A suspension bracket kit components.

Actual angles for 502A with a constant voltage transformer:

Diagram Description: Shows the 502A loudspeaker with a bracket, indicating a weight of 6.8 kg (15 lb).

Recommended Power Amplifiers

Selecting the proper amplifier size requires analysis of transducer power rating, dynamic range, desired sound pressure levels, and other factors. The following table provides recommended power amplifier ranges for Bose Panaray loudspeakers:

CAUTION: Failure to follow these guidelines may result in damage to the loudspeaker!

Refer to the specifications on pro.Bose.com for PowerMatch® amplifiers to determine the best model for your system design.

Recommended DSP Settings

Bose Panaray loudspeakers require active equalization for optimal sound quality. Recommended equalization is available in the preset libraries of Bose PowerMatch® configurable power amplifiers and ControlSpace® processors. EQ values can be downloaded using the Hardware Manager feature in ControlSpace Designer™ software.

The following tables contain recommended parametric EQ values confirmed with Bose ControlSpace Designer software and Bose Engineered Sound Processor (ESP) hardware. Results may vary with other DSP hardware.

Panaray 802 Series IV Recommended EQ Settings

Panaray 402 Series IV Recommended EQ Settings

Panaray 502 A Recommended EQ Settings

Additional Resources

Visit pro.Bose.com for more information, including specifications, technical literature, product warranty, parts and accessories, and global support contact information.

Americas (USA, Canada, Mexico, Central America, South America)

Bose Corporation
The Mountain
Framingham, MA 01701 USA
Corporate Center: 508-879-7330
Americas Professional Systems, Technical Support: 800-994-2673

Australia

Bose Pty Limited
Unit 3/2 Holker Street
Newington NSW Australia
61 2 8737 9999

Belgium

Bose N.V. / S.A
Limesweg 2, 03700
Tongeren, Belgium
012-390800

China

Bose Electronics (Shanghai) Co Ltd
25F, L'Avenue
99 Xianxia Road
Shanghai, P.R.C. 200051 China
86 21 6010 3800

France

Bose S.A.S
12 rue de Temara 78100
St. Germain-en-Laye, France
01-30616363

Germany

Bose GmbH
Max-Planck Strasse 36D 61381
Friedrichsdorf, Deutschland
06172-7104-0

Hong Kong

Bose Limited
Suites 2101-2105, Tower One, Times Square
1 Matheson Street, Causeway Bay, Hong Kong
852 2123 9000

India

Bose Corporation India Private Limited
Salcon Aurum, 3rd Floor
Plot No. 4, Jasola District Centre
New Delhi - 110025, India
91 11 43080200

Italy

Bose SpA
Centro Leoni A – Via G. Spadolini
5 20122 Milano, Italy
39-02-36704500

Japan

Bose Kabushiki Kaisha
Sumitomo Fudosan Shibuya Garden Tower 5F
16-17, Nanpeidai-cho
Shibuya-ku, Tokyo, 150-0036, Japan
TEL 81-3-5489-0955
www.bose.co.jp

The Netherlands

Bose BV
Nijverheidstraat 8 1135 GE
Edam, Nederland
0299-390139

United Kingdom

Bose Ltd
1 Ambley Green, Gillingham Business Park
KENT ME8 ONJ
Gillingham, England
0870-741-4500

See website for other countries