Bose Panaray 802 Series IV Loudspeaker
Installation and Safety Guide
Important Safety Instructions
⚠️ WARNING: This product is intended for installation by professional installers only.
All Bose products must be used in accordance with local, state, federal, and industry regulations. The installer is responsible for ensuring installation complies with all applicable codes, including local building codes and regulations. Consult the local authority having jurisdiction before installing.
⚠️ WARNING: Unsafe mounting or overhead suspension of heavy loads can result in serious injury and equipment damage. Only professional installers with knowledge of proper hardware and safe mounting techniques should attempt overhead installation.
Guidelines for Permanent Installation:
- Prior to overhead installation, a licensed professional engineer must approve the location and method of attachment to the building structure, ensuring compliance with all codes and regulations.
- Ensure the mounting surface and method can support the total system weight (37 lb / 16.8 kg). A 10:1 safety factor is recommended.
- Obtain mounting system components from reputable manufacturers. Bose mounting accessories are recommended. Custom hardware requires review by a licensed professional engineer.
- Bose 802 Series IV Loudspeakers feature integrated M8 threaded inserts. Use only metric hardware (Class 8.8 or equivalent). Do NOT use SAE 5/16" hardware.
- Use lock washers or a locking compound (e.g., LOCTITE® THREADLOCKER BLUE 242®) for vibration-resistant assembly.
- Tighten fasteners to 50 inch-pounds (5.6 Newton-meters). Over-tightening can cause irreparable damage and create an unsafe assembly.
- Do not alter threaded attachment points.
- Use a separate safety cable attached to the cabinet at a point distinct from the load-bearing attachment points. Consult a professional for proper design and installation.
❗ CAUTION: Installed loudspeakers require regular inspection and maintenance for safe operation. Inspect mounting hardware for corrosion or damage and replace worn/damaged components immediately.
❗ CAUTION: Do not modify loudspeakers or mounting accessories. Unauthorized alterations can compromise safety and lead to damage, injury, or death.
This product conforms to all applicable EU directive requirements. The complete declaration of conformity can be found at www.Bose.com/compliance.
Product Overview
The Bose® Panaray® 802® Series IV sound-reinforcement loudspeaker features full-range cone transducers in a proprietary Articulated Array® for exceptional reliability in adverse conditions and natural vocal clarity. It is designed for both indoor and outdoor permanently-installed sound systems.
The 802 Series IV provides wide 120° horizontal and 100° vertical coverage with low-frequency response down to 50 Hz, all within a lightweight, compact enclosure. As the fourth generation, it continues the legacy of reliability, wide coverage, and natural sound quality that has made the 802 loudspeaker a best-seller worldwide.
Carton Contents
- Bose Panaray 802 Series IV Loudspeaker
- Installation Guide
Diagram Descriptions
Loudspeaker Dimensions
The loudspeaker dimensions are provided in three views: Top, Rear, and Bottom, along with a Right view (which applies to both sides). Key dimensions include:
- Overall width: 20.16 inches (512.06 mm)
- Overall height: 12.52 inches (318.00 mm)
- Overall depth: 13.32 inches (338.33 mm)
- Rear mounting points: Two M8 x 1.25 threaded inserts.
- Bottom mounting points: Two M8 x 1.25 threaded inserts.
Installation: Mounting with the U-bracket
The Bose® 802 Series IV loudspeaker can be mounted on a wall or ceiling using a U-bracket accessory kit (not included). This installation should be performed by trained installers.
Recommended Tool: 5 mm Allen wrench.
❗ CAUTION: The loudspeaker weighs 37 lb (16.8 kg). Use caution when lifting to avoid injury or damage. Do not rest loudspeakers on their grilles.
Mounting Procedure:
- Choose a mounting location that can safely support the loudspeaker's weight (37 lb / 16.8 kg). Ensure the mounting surface and method are structurally sound, adhering to local building codes and regulations. A 10:1 safety weight ratio is recommended.
- Hold the U-bracket in the desired mounting location and mark the hole positions.
- Drill four holes and mount the bracket using four screws.
- Attach a bracket spacer to each side of the speaker. Insert an M8 cap screw into the front hole on each side of the speaker. Do not tighten yet.
- Place the speaker onto the U-bracket.
- Tilt the speaker to the desired angle and insert the second M8 cap screw on each side of the speaker.
- Using a 5 mm Allen wrench, tighten all four cap screws to 50 inch-pounds (5.6 Newton-meters).
- Connect field wiring and test loudspeaker operation.
Installation: Mounting on a Speaker Stand
The 802 Series IV loudspeaker can be mounted on a speaker stand, such as the Bose® SS10 model, using its thumb screws for attachment to the adapter on the stand's top. Note: Other stands have not been tested and may create a tipping hazard.
Recommended Power Amplifiers
Selecting the proper amplifier size requires analysis of the loudspeaker's power rating, dynamic range, desired sound pressure levels, and other factors. The following table provides recommended power amplifier ranges for Bose Panaray® loudspeakers:
| Model | Nominal Impedance | Required Channels | Amp Power Rating |
|---|---|---|---|
| 802 Series IV | 8 ohms | 1 | 250 - 500 Watts |
❗ CAUTION: Failure to follow these guidelines may result in damage to the loudspeaker!
Refer to the specifications on pro.bose.com for PowerMatch® amplifiers to determine the best model for your system design.
Recommended DSP Settings
The Bose Panaray 802 Series IV loudspeaker requires active equalization for optimal sound quality. Recommended equalization is available in the preset libraries of Bose PowerMatch® Configurable Power Amplifiers and ControlSpace® engineered sound and loudspeaker processors.
Technical Specifications
| Category | Specification |
|---|---|
| System Performance: Frequency Range (-10 dB) | 50 Hz - 16 kHz |
| System Performance: Coverage Pattern, Horizontal | 120° |
| System Performance: Coverage Pattern, Vertical | 100° |
| System Performance: Long-Term Power Handling | 300 W |
| System Performance: Calculated Maximum SPL @ 1 m, peak | 123 dB |
| System Performance: Requires active EQ for best performance | Yes |
| Transducers: Driver Compliment | Eight (8) 4.5" (114 mm) full-range environmental drivers |
| Transducers: Nominal Impedance | 8 ohms |
| Physical: Dimensions | 13.3" H x 20.5" W x 12.9" D (338 mm x 520 mm x 327 mm) |
| Physical: Net Weight | 37 lb (16.8 kg) |
| Physical: Finish Color | Black |
| Physical: Environmental Rating | Outdoor (IP55) |
| Physical: Suspension / Mounting | Eight (8) M8 x 1.25 inserts (2 back, 2 bottom) |
| Physical: Shipping Weight | 42 lb (19.1 kg) |
| Product Code | 739058-0110 |
Notes:
- Power handling using Bose Extended-Lifecycle Test.
- Maximum SPL calculated from sensitivity and power handling specifications, exclusive of power compression.
- All specifications subject to change without notice.
