Hager EHN010/EHN011 Daily Time Switch

Product Overview

The Hager EHN010 and EHN011 are daily time switches designed for controlling electrical circuits based on a daily program. They are suitable for lighting, ventilation, fountains, and advertising applications in closed, dry rooms.

Key Features:

• Analogue time switch
• 1 channel
• Daily program
• 16 A switching capacity
• Optional power reserve (EHN011 model)
• Mounts on standard 35mm DIN rail (TH 35-7.5)

Device Description (Refer to Figure 01)

The device features the following components:

• 1. Marking: A marker used for reading the current time.
• 2. Switching Disk: The main disk that displays and allows setting of the switching times.
• 3. Switching Segments: These are movable segments on the switching disk, each representing a 15-minute interval, used to define ON/OFF periods.
• 4. Mode Switch: A selector to choose the operating mode: 'Auto' for automatic timed operation, '1' for continuous ON, or '0' for continuous OFF.

Installation and Electrical Connection

Warning: Risk of electric shock if live parts are touched. Electric shock can be fatal. Always disconnect all power before working on the device and ensure surrounding live parts are covered.

1. Mounting: Snap the device onto a standard 35mm DIN rail (as illustrated in Figure 02).
2. Wiring: Connect the device according to the provided wiring diagram (refer to Figure 03).
3. Power Restoration: After connections are made, switch the miniature circuit breaker back on.

Setting the Time and Program

1. Set Current Time: To set the current time, turn the switching disk (2) upwards (as shown in Figure 05).
2. Define Switching Times: Set the desired ON/OFF times by manipulating the switching segments (3). Push segments downwards to the right for ON, or upwards to the left for OFF (as illustrated in Figure 06).
3. Select Operating Mode: Use the mode switch (4) to select the desired operation: 'Auto' for automatic timed control, '1' for permanent ON, or '0' for permanent OFF (as shown in Figure 08).

Technical Data

• Operating Voltage: 230 V~, +10%/-15% or 240 V~, ± 6%
• Frequency: 50 - 60 Hz (EHN011), 50 Hz (EHN010)
• Cycle: 24 hours
• Shortest Switching Time: 15 minutes
• Own Consumption: 1 W (EHN010), 0.5 W (EHN011)
• Switching Capacity: 16 A, 250 V~, AC1; 4 A, 250 V~, cos φ = 0.6
• Switching Capacity Min.: 24 V~ / 100 mA
• LED Lamps: < 2 W (up to 30 W total), > 2 W (up to 300 W total)
• Incandescent/Halogen Lamps: 1000 W
• Fluorescent Lamps (electronic ballast): 600 W (10 x 58 W)
• Fluorescent Lamps (with ballast): 600 VA (max. 70 μF)
• Fluorescent Lamps (without ballast): 1000 VA
• Compact Fluorescent Lamps: 150 W
• Power Reserve: None (EHN010), 120 hours at 230 V (EHN011)
• Accuracy Rate Max.: ± 1 s/day
• Conductor Cross-section: 1 - 6 mm²
• Miniature Circuit Breaker: 16 A
• Contact Type: Normally open contact
• Opening Width: < 3 mm
• Protection Class: II
• Degree of Protection: IP 20
• Operating Temperature: -20 °C to +50 °C (EHN010), -10 °C to +50 °C (EHN011)
• Storage Temperature: -25 °C to +70 °C
• Width: 17.5 mm / 1 Module (PU)
• Rated Surge Voltage: 4 kV
• Mounting/Operating Height: < 2000 m
• Mode of Action: 1 BRTU (EHN010), 1 BSTU (EHN011)
• Contamination Level: 2

Safety Instructions

Electrical equipment installation and assembly must be performed by a qualified electrician, adhering to national installation standards, directives, regulations, and accident prevention rules. Failure to comply with these instructions may result in device damage, fire, or other hazards.

Correct Use

This device is intended for controlling lighting, ventilation, fountains, advertising, and similar applications within closed, dry rooms. It is designed for mounting on a standard 35mm DIN rail (TH 35-7.5) in accordance with DIN EN 60715. Switching of any external conductor is permitted, but switching of SELV (Safety Extra Low Voltage) is not allowed.

Correct Disposal of Product (Waste Electrical & Electronic Equipment)

This product is marked with the WEEE symbol, indicating it should not be disposed of with regular household waste at the end of its service life. This applies within the European Union and other European countries with separate collection systems. To prevent potential harm to the environment or human health, please separate this device from other waste types. This practice supports the sustainable reuse of material resources.

Private consumers are advised to contact the retailer where the product was purchased or their local municipal administration for information on environmentally friendly disposal methods. Commercial consumers should contact their suppliers and review the terms and conditions of their purchase agreement. This product must not be mixed with other commercial waste for disposal.