INSTALLATION Product Manual
IMPORTANT INFORMATION!
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
❓
Read manual before assembly.
AVOID SCRATCHES!
In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
❌ ✔️
Assemble on a soft surface like a rug to prevent scratches.
IMPROVE EFFICIENCY !
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
???
Two people recommended for faster assembly.
ANTI-TOPPLE WARNING !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
⚠️
Always secure furniture to the wall using anti-tip hardware to prevent tipping hazards.
IMPORTANT!
It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.
For regular maintenance and cleaning of the product:
- For the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag.
- For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
Tools and Parts Required
Tools:
| Icon/Description | Notes |
|---|---|
| ? [Phillips screwdriver] | For screws A, D, E, F, G |
| ? [Flathead screwdriver] | For cam locks B |
| ? [Hammer/Mallet] | For wooden dowels C |
Parts List:
When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.
| Identifier | Description | Quantity |
|---|---|---|
| A | M6 x 42 mm | 64 |
| B | Ø 15 x 10 mm | 64 |
| C | Ø 8 x 30 mm | 8 |
| D | M5 x 40 mm | 36 |
| E | M3.5 x 12 mm | 74 |
| F | M3.5 x 20 mm | 8 |
| G | M3.5 x 30 mm | 2 |
| H | (Anti-dumping hardware component) | 2 |
| I | (Anti-dumping hardware component) | 2 |
| 17 | Drawer Slides (14" / 3508) | 9 SETS |
| 1 | Top Panel | 1 |
| 2 | Left Side Panel | 1 |
| 3 | Right Side Panel / Vertical Divider | 1 |
| 4 | Drawer Support Panel | 1 |
| 5 | Drawer Support Panel | 1 |
| 6 | Drawer Side Panel | 6 |
| 7 | Drawer Back Panel | 3 |
| 8 | Drawer Front Panel | 3 |
| 9 | Back Panel Support | 1 |
| 10 | Drawer Front Panel | 3 |
| 11 | Drawer Front Panel | 3 |
| 12 | Drawer Front Panel | 3 |
| 13 | Drawer Side Panel | 6 |
| 14 | Drawer Back Panel | 3 |
| 15 | Drawer Side Panel | 3 |
| 16 | Drawer Bottom Panel | 9 |
| 18 | Drawer Front Panel | 3 |
| 19 | Back Panel | 1 |
Assembly Instructions
Drawer Slide Separation: Slides must be separated before assembly. After separation, set aside until needed for assembly.
STEP 1: Extend Slide
Diagram shows a drawer slide being extended.
STEP 2: Push Lever UP
Diagram shows a hand pushing up a small lever on the drawer slide.
STEP 3: Remove Runner
Diagram shows the inner runner of the slide being detached after the lever is pushed.
Step 1
Insert quickfit screw(A) to part 2. Fix slide rail 17 to part 2 using screw(E) as shown.
Diagram shows part 2 (left side panel) and slide rail 17. Screw (A) is inserted into pre-drilled holes on part 2. Slide rail 17 is then attached to the inside face of part 2 using screws (E). A magnified view shows the correct placement of screw (A) and the attachment of slide rail 17 with screw (E).
❗ Please pay attention to the holes where the accessories are inserted and do not use an electric screwdriver.
Step 2
Insert quickfit screw(A) to part 3. Fix slide rail 17 to part 3 using screw(E) as shown.
Diagram shows part 3 (right side panel/vertical divider) and slide rail 17. Screw (A) is inserted into pre-drilled holes on part 3. Slide rail 17 is then attached to the inside face of part 3 using screws (E). A magnified view shows the correct placement of screw (A) and the attachment of slide rail 17 with screw (E).
❗ Please pay attention to the holes where the accessories are inserted and do not use an electric screwdriver.
Step 3
Fix slide rail 17 to the front of part 4 using screw(E) as shown.
Diagram shows part 4 (drawer support panel) and slide rail 17. Slide rail 17 is attached to the front edge of part 4 using screws (E). A magnified view shows screw (E) being used for attachment.
Step 4
Fix slide rail 17 to the back of part 4 using screw(E) as shown. Please note, the pre-drilling of the rail on the front and back of this board is asymmetrical. Please install the rails according to the picture. This side as shown must be facing the middle drawer after installation is complete.
Diagram shows part 4 (drawer support panel) and slide rail 17. Slide rail 17 is attached to the back edge of part 4 using screws (E). The diagram highlights that the pre-drilling is asymmetrical and indicates the correct orientation for facing the middle drawer.
Step 5
Fix slide rail 17 to the front of part 5 using screw(E) as shown. Please note, the pre-drilling of the rail on the front and back of this board is asymmetrical. Please install the rails according to the picture. This side as shown must be facing the middle drawer after installation is complete.
Diagram shows part 5 (drawer support panel) and slide rail 17. Slide rail 17 is attached to the front edge of part 5 using screws (E). The diagram highlights that the pre-drilling is asymmetrical and indicates the correct orientation for facing the middle drawer.
Step 6
Fix slide rail 17 to the back of part 5 using screw(E) as shown.
Diagram shows part 5 (drawer support panel) and slide rail 17. Slide rail 17 is attached to the back edge of part 5 using screws (E).
Step 7
Insert quickfit screw(A) to part 7 as shown.
Diagram shows part 7 (drawer back panel). Screw (A) is inserted into pre-drilled holes on part 7.
Step 8
Insert quickfit screw(A) to part 6 as shown (x3).
Diagram shows part 6 (drawer side panel). Screw (A) is inserted into pre-drilled holes on part 6. This step is repeated for three drawer side panels.
Step 9
Insert quickfit screw(A) to part 18 as shown.
Diagram shows part 18 (drawer front panel). Screw (A) is inserted into pre-drilled holes on part 18.
Step 10
Attach part 6 and 18 to part 4 and 5, turn cam locks(B) clockwise to tighten as shown. Attach part 7 to part 4 and 5, turn cam locks(B) clockwise to tighten as shown.
Diagram shows drawer components being assembled. Parts 6 (drawer sides) and 18 (drawer front) are attached to parts 4 and 5 (drawer supports) using cam locks (B). Part 7 (drawer back) is also attached to parts 4 and 5 using cam locks (B). A magnified view shows a cam lock (B) being inserted and turned clockwise to secure the connection.
Step 11
Attach part 2, 3 to part 6, 18 and 7, turn cam locks(B) clockwise to tighten as shown.
Diagram shows the main frame assembly. Parts 2 (left side panel) and 3 (right side panel/divider) are attached to the assembled drawer structure (parts 6, 18, 7) using cam locks (B). A magnified view shows a cam lock (B) being inserted and turned clockwise.
Step 12
Connect part 19 and part 8 with part 9 and insert into the available slots of part 2, 3 and 7 as shown.
Diagram shows the back panel assembly. Part 19 (back panel) is connected to part 9 (back panel support), and then this assembly is inserted into the slots of parts 2, 3, and 7, forming the back of the unit.
Step 13
Insert quickfit screw(A) to part 1 as shown. Fix part(I) to part 1 using screw(E) as shown.
Diagram shows part 1 (top panel). Screws (A) are inserted into pre-drilled holes. Part I (an anti-dumping bracket) is then attached to part 1 using screw (E). A magnified view shows the correct placement of screws (A) and (E).
❗ Please pay attention to the holes where the accessories are inserted and do not use an electric screwdriver.
Step 14
Cover part 1 to the assembled unit with wooden dowel(C), and turn cam locks(B) clockwise to tighten as shown.
Diagram shows part 1 (top panel) being placed onto the main assembled unit. Wooden dowels (C) are inserted into corresponding holes, and cam locks (B) are used to secure the top panel. A magnified view shows the cam lock mechanism.
Step 15
Fix back panel 19 and 8 to the assembled unit with screw(F) as shown.
Diagram shows the back panel (19) and drawer front panel (8) being secured to the main unit using screws (F). A magnified view shows screw (F) being used to attach panel 8.
Step 16
Install anti-dumping as shown in the figure.
Diagram shows the installation of anti-tip hardware. Bracket I is attached to the top rear of the unit using screw G. Bracket H is shown being attached to a wall. The two brackets are then connected by a strap (implied).
Step 1: Attach bracket I to the unit with screw G.
Step 2: Attach bracket H to the wall.
Step 3: Connect the unit to the wall using the provided strap.
Step 17
Insert quickfit screw(A) to part 10 as shown (x3).
Diagram shows part 10 (drawer front panel). Screw (A) is inserted into pre-drilled holes on part 10. This step is repeated for three drawer front panels.
Step 18
Insert quickfit screw(A) to part 11 as shown (x3).
Diagram shows part 11 (drawer front panel). Screw (A) is inserted into pre-drilled holes on part 11. This step is repeated for three drawer front panels.
Step 19
Insert quickfit screw(A) to part 12 as shown (x3).
Diagram shows part 12 (drawer front panel). Screw (A) is inserted into pre-drilled holes on part 12. This step is repeated for three drawer front panels.
Step 20
Connect part 13 and 14 to part 15 using screw(D) as shown (x9).
Diagram shows the assembly of drawer boxes. Parts 13 (drawer side panels) and 14 (drawer back panels) are attached to part 15 (drawer side panel) using screws (D). This step is repeated for nine drawer box assemblies.
Step 21
Insert part 16 into the available slots as shown (x9).
Diagram shows part 16 (drawer bottom panel) being slid into the grooves of the assembled drawer box (from Step 20). This is done for nine drawer boxes.
Step 22
Attach part 10 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown (x3).
Diagram shows part 10 (drawer front panel) being attached to the drawer box (parts 13 and 14) using cam locks (B). A magnified view shows the cam lock mechanism. This is done for three drawers.
Step 23
Attach part 11 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown (x3).
Diagram shows part 11 (drawer front panel) being attached to the drawer box (parts 13 and 14) using cam locks (B). A magnified view shows the cam lock mechanism. This is done for three drawers.
Step 24
Attach part 12 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown (x3).
Diagram shows part 12 (drawer front panel) being attached to the drawer box (parts 13 and 14) using cam locks (B). A magnified view shows the cam lock mechanism. This is done for three drawers.
Step 25
Fix slide rail 17 to part 13 and 14 using screw(E) as shown (x3).
Diagram shows slide rail 17 being attached to the outer side of the drawer box (parts 13 and 14) using screws (E). A magnified view shows the attachment. This is done for three drawers.
Step 26
Fix slide rail 17 to part 13 and 14 using screw(E) as shown (x3).
Diagram shows slide rail 17 being attached to the outer side of the drawer box (parts 13 and 14) using screws (E). A magnified view shows the attachment. This is done for three drawers.
Step 27
Fix slide rail 17 to part 13 and 14 using screw(E) as shown (x3).
Diagram shows slide rail 17 being attached to the outer side of the drawer box (parts 13 and 14) using screws (E). A magnified view shows the attachment. This is done for three drawers.
Step 28
Align the rails, put all drawers as shown. Please note, part 10 drawers are put in left, part 11 in middle, part 12 in right.
Diagram shows the completed dresser with all drawers inserted. The diagram indicates that drawers with front panel 10 are placed on the left, drawers with front panel 11 are in the middle, and drawers with front panel 12 are on the right. A magnified view shows the drawer slides engaging within the unit.
WARRANTY
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
- Before making a claim, contact customer service. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. Service will respond within 48 hours. If there is out of stock, a shipping date will be provided.
- The product must be used in accordance with the instructions provided.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Does not include damage during installation, but includes damage during transportation.
Scope of responsibility
- Shall not bear any responsibility for misuse or user damage and / or loss of parts during the installation of furniture.
- After using, the damage and scratches of the furniture are not covered by the warranty.
The Warranty Relates to All Bought in The US and Covers The Following Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
