RHEEM WATER HEATER PARTS & ACCESSORIES
PRODUCT CATALOG
table of contents
3 Introduction
6 Electric Water Heater Elements Screw-In Elements 1 inch Screw-In Elements 1-3/8 inch Flange Elements Flat Flange Elements
8 Element Accessories Element Wrench Element Gaskets & Gasket Kits Adapt-O-Flange Element Conversion Kit
8 Water Heater Repair Kits Good Plumbers Pack Better Plumbers Pack
9 Thermostats APCOM Style Thermostats Therm-O-Disc Style Thermostats Thermostat Covers
10 Gas Water Heater Parts Gas Controls Natural Gas Gas Controls LP Gas Pilot Burner Assemblies Thermocouple Kits
10 Installation Accessories Flexible Water Connector Stainless Steel Flexible Water Connectors Flexible Gas Connectors Water Heater Installation Kits
12 Water Heater Parts Compression Fittings Dielectric Unions Nipples Plastic Lined Nipples Plastic Lined/Heat Trap Drain Valves T&P Valves Run-Off Tubes Dip Tubes Anode Rods Aluminum Anode Rods R Tech Resistor Magnesium Anode Rods Magnesium Flexible Anode Rods R Tech Resistor Magnesium Water Heater Insulation Blankets Drain Pans Plastic Drain Pans Aluminum Expansion Tanks Water Heater Stand
2
W W W. R H E E M . C O M
Located in Randleman, North Carolina with a 185,000 sq. ft. distribution center, the Replacements Parts Department provides products and services including the support of new equipment sales by providing OEM replacement parts, and parts identification. In addition, we sell and market aftermarket parts and products that are included in the installation, maintenance and servicing of HVAC equipment, water heaters and other residential power equipment.
RHEEM NATIONAL CUSTOMER SERVICE
Customer Service: 800.621.5622 · Parts & Accessories: 800.621.5622 Warranty: www.MyRheem.com & www.MyRuud.com, fax 800.535.9538, email parts@rheem.com Technical Service: 800.HEATER3 (800.432.8373), email techserv@rheem.com. web www.rheem.com
For products not shown in this brochure, please contact the Rheem National Customer Service: 800.621.5622.
To place your order, call 800.621.5622 or fax 800.535.9538.
T O P L A C E Y O U R O R D E R C A L L 8 0 0.6 2 1.5 6 2 2, FA X 8 0 0.5 3 5.9 5 3 8
3
RESIDENTIAL RHEEM® ELECTRIC WATER HEATER CONSTRUCTION
TEMPERATURE AND PRESSURE RELIEF VALVE Commonly referred to as the "T&P" valve. This safety device opens to allow water to escape from the water heater in the unlikely event that either the tank pressure or temperature becomes excessive.
PLASTIC LINED NIPPLES/HEAT TRAPS Thermoplastic lined nipples impede galvanic corrosion. "Heat trap" nipples also contain a check valve to reduce heat loss between hot water in the tank and cold water pipes.
UPPER THERMOSTAT Maintains desired temperature of the water by controlling the power going to the heating elements. Also
controls the lower thermostat.
COLD WATER INLET AND DIP TUBE
The connection point for incoming cold water. The inlet connects directly to a dip tube which directs the
incoming water to the bottom of the tank.
LOWER THERMOSTAT Maintains desired temperature of the water by regulating the power going
to the lower heating element.
DRAIN VALVE Plastic or metal valve that allows the tank to be emptied should service be required.
4
W W W. R H E E M . C O M
ANODE ROD A replaceable component made of magnesium alloy or other metals that protects the tank against premature corrosion.
HEATING ELEMENTS The heart of an electric water heater. Heating elements generate the heat required to bring the water in the tank to the desired temperature. Elements are made from either Stainless Steel or Copper. The voltage and wattage requirements are dependent on the heater's capacity.
RESIDENTIAL RHEEM® GAS WATER HEATER CONSTRUCTION
PLASTIC LINED NIPPLES/HEAT TRAPS Thermoplastic lined nipples impede galvanic corrosion. "Heat trap" nipples also contain a check valve to reduce heat loss between hot water in the tank and cold water pipes.
TEMPERATURE AND PRESSURE RELIEF VALVE Commonly referred to as the "T&P" valve. This safety device opens to allow water to escape from the water heater in the unlikely event that either the tank pressure or temperature becomes excessive.
COLD WATER INLET AND DIP TUBE
The connection point for incoming cold water. The inlet connects directly to a dip tube
which directs the incoming water to the bottom of the tank.
THERMOSTAT Maintains desired temperature of the water by regulating the power going
to the lower heating element.
DRAIN VALVE Plastic or metal valve that allows the tank to be emptied should service be required.
ANODE ROD A replaceable component made of magnesium alloy or other metals that protects the tank against premature corrosion.
BURNER ASSEMBLY Heats the water in the tank by using a flame from either natural or propane gas.
T O P L A C E Y O U R O R D E R C A L L 8 0 0.6 2 1.5 6 2 2, FA X 8 0 0.5 3 5.9 5 3 8
5
ELECTRIC WATER HEATER ELEMENTS
SP10869MM
Screw-In Elements 1 inch
Screw-in elements with 1 inch NPSM threads fit most water heaters using screw-in elements.
Stainless Steel Premium Resistored
Outer sheath of Incoloy® 800 to resist failure from "dry firing;" built-in resistor to help prolong tank life.
PART NO
VOLTAGE WATTAGE INSERTION
(V)
(W)
DEPTH (IN) TYPE
SP10869KL 240 3500 13-1/2 SSR
SP10869MM 240 4500 13-1/2 SSR
SP10869ML 240 4500 15-1/2 SSR
SP10869PH 240 5500 13-1/2 SSR
WATT
MOUNTING THREAD HEX HEAD
DENSITY RESISTORED TYPE SIZE - NPSM (IN) SIZE (IN)
LWD
Yes Screw-in 1
1-1/2
LWD
Yes Screw-in 1
1-1/2
LWD
Yes Screw-in 1
1-1/2
HWD Yes Screw-in 1
1-1/2
CASE QTY CASE REQ
---- ---- ---- ----
Stainless Steel Non-Resistored
Outer sheath of Incoloy® 800 to resist failure from "dry firing."
PART NO
VOLTAGE WATTAGE INSERTION
(V)
(W)
DEPTH (IN) TYPE
UV12904 240 4500 13
SS
UV129046PK 240 4500 13
SS
WATT
MOUNTING THREAD HEX HEAD
DENSITY RESISTORED TYPE SIZE - NPSM (IN) SIZE (IN)
LWD
-- Screw-in 1
1-1/2
LWD
-- Screw-in 1
1-1/2
CASE QTY CASE REQ
---- 6 Yes
UV12904
Copper Resistored
Built-in resistor to help prolong tank life.
PART NO
VOLTAGE WATTAGE INSERTION
(V)
(W)
DEPTH (IN) TYPE
SP10874FH 120 1500 7-1/2 CR
SP10874GH 120 2000 7-3/4 CR
SP10552MH 240 4500 13-1/2 CR
SP10552ML 240 4500 13-3/4 CR
WATT
MOUNTING THREAD HEX HEAD
DENSITY RESISTORED TYPE SIZE - NPSM (IN) SIZE (IN)
HWD Yes Screw-in 1
1-1/2
HWD Yes Screw-in 1
1-1/2
HWD Yes Screw-in 1
1-1/2
LWD
Yes Screw-in 1
1-1/2
CASE QTY CASE REQ
---- ---- ---- ----
SP10874FH
Copper Non-Resistored
UV12896
PART NO
VOLTAGE WATTAGE INSERTION
(V)
(W)
DEPTH (IN) TYPE
UV12890 120 1500 7-5/8 CU
UV1289012PK 120 1500 7-5/8 CU
UV12892 120 2000 7-5/8 CU
UV1289212PK 120 2000 7-5/8 CU
UV12891 240 1500 7-5/8 CU
UV1289112PK 240 1500 7-5/8 CU
UV12893 240 2000
7
CU
UV1289312PK 240 2000
7
CU
UV12894 240 2500 9-1/2 CU
UV1289412PK 240 2500 9-1/2 CU
UV12895 240 3000 10-5/8 CU
UV1289512PK 240 3000 10-5/8 CU
UV12896 240 3500 12-1/8 CU
UV1289612PK 240 3500 12-1/8 CU
UV12897 240 3800 13-3/8 CU
UV1289712PK 240 3800 13-3/8 CU
UV12898 240 4000 13-1/4 CU
WATT
MOUNTING THREAD HEX HEAD
DENSITY RESISTORED TYPE SIZE - NPSM (IN) SIZE (IN) CASE QTY CASE REQ
HWD
-- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD
-- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD
-- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD -- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD
-- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD
-- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD
-- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD
-- Screw-in 1
1-1/2 -- --
HWD
-- Screw-in 1
1-1/2 12 Yes
HWD
-- Screw-in 1
1-1/2 -- --
continued on next page
6
W W W. R H E E M . C O M
ELECTRIC WATER HEATER ELEMENTS
Copper Non-Resistored CONTINUED
PART NO
VOLTAGE WATTAGE INSERTION
(V)
(W)
DEPTH (IN) TYPE
UV13049 240 4500 7-7/8 CU
UV1304912PK 240 4500 7-7/8 CU
UV12901 240 4500 11-3/4 CU
UV1290112PK 240 4500 11-3/4 CU
UV12899 240 4500 13-1/2 CU
UV1289912PK 240 4500 13-1/2 CU
UV12900 240 5500 9-7/8 CU
UV1290012PK 240 5500 9-7/8 CU
WATT
MOUNTING THREAD HEX HEAD
DENSITY RESISTORED TYPE SIZE - NPSM (IN) SIZE (IN)
MWD -- Screw-in 1
1-1/2
MWD -- Screw-in 1
1-1/2
LWD
-- Screw-in 1
1-1/2
LWD
-- Screw-in 1
1-1/2
HWD
-- Screw-in 1
1-1/2
HWD
-- Screw-in 1
1-1/2
LWD
-- Screw-in 1
1-1/2
LWD
-- Screw-in 1
1-1/2
CASE QTY CASE REQ
---- 12 Yes ---- 12 Yes ---- 12 Yes ---- 12 Yes
Screw-In Elements 1-3/8 inch Copper Non-Resistored
PART NO
UV12902
VOLTAGE WATTAGE INSERTION
(V)
(W)
DEPTH (IN) TYPE
240 4500 13
CU
WATT DENSITY
LWD
MOUNTING THREAD HEX HEAD RESISTORED TYPE SIZE - NPSM (IN) SIZE (IN)
-- Screw-in 1-3/8 1-7/8
CASE QTY CASE REQ
----
UV12902
UV13048 UV13047C
Flange Elements Stainless Steel Non-Resistored
PART NO
VOLTAGE (V)
UV12911
240
UV1291112PK 240
UV13048
240
UV1304812PK 240
WATTAGE (W)
2500 2500 4500 4500
INSERTION DEPTH (IN)
11-1/4 11-1/4 13-3/4 13-3/4
TYPE
SS SS SS SS
Copper Non-Resistored
PART NO
VOLTAGE WATTAGE INSERTION
(V)
(W)
DEPTH (IN)
TYPE
UUV12909
240
3500
12-1/2
CU
UV1290912PK 240
3500
12-1/2
CU
UV13047C
240
4500
7-3/4
CU
UV13047C12PK 240
4500
7-3/4
CU
UV12910
240
4500
13-5/8
CU
UV129106PK 240
4500
13-5/8
CU
WATT DENSITY
LWD LWD HWD HWD
MOUNTING RESISTORED TYPE
--
Flange
--
Flange
--
Flange
--
Flange
CASE QTY
-- 12 -- 12
CASE REQ
-- Yes -- Yes
WATT DENSITY
HWD HWD MWD MWD HWD HWD
MOUNTING RESISTORED TYPE
--
Flange
--
Flange
--
Flange
--
Flange
--
Flange
--
Flange
CASE QTY
-- 12 -- 12 -- 6
CASE REQ
-- Yes -- Yes -- Yes
Flat Flange Elements Copper Non-Resistored
PART NO
VOLTAGE (V)
UV12907
240
UV1290712PK 240
WATTAGE (W)
4500 4500
INSERTION DEPTH (IN)
13-1/2 13-1/2
TYPE
CU CU
WATT DENSITY
HWD HWD
MOUNTING CASE CASE
RESISTORED TYPE
QTY REQ
-- Flat Flange -- --
-- Flat Flange 12 Yes
UV12907
SSR = Stainless Steel Resistored SS = Stainless Steel CR = Copper Resistored CU = Copper HWD = High Watt Density MWD = Medium Watt Density LWD = Low Watt Density
T O P L A C E Y O U R O R D E R C A L L 8 0 0.6 2 1.5 6 2 2, FA X 8 0 0.5 3 5.9 5 3 8
7
UV38628
ELEMENT ACCESSORIES
Element Wrench
PART NO
UV38628 UV3862812PK 49057
DESCRIPTION
Element Wrench (Fits 1-1/2 in. Hex) Element Wrench (Fits 1-1/2 in. Hex) Element Wrench - Dual (Fits 1-1/2 in. & 1-7/8 in. Hex)
49057
CASE QTY
-- 12 --
CASE REQ
-- Yes --
UV12914
AP6708-9
AP6614J
AP10363
Element Gaskets & Gasket Kits
PART NO
AP6708-9 AP6614J AP10363 UV12914 UV129146PK
DESCRIPTION
Gasket - 1 in. Screw-in Element (1-1/4 in. I.D. x 1-1/2 in. O.D. x 5/32 in. thick) Gasket - Flange Element (1-1/8 in. I.D. x 1-11/16 in. O.D. x 1/2 in. thick) Gasket - Flange Element (1-1/4 in. I.D. - 2-1/2 in. x 2-1/2 in. x 1/16 in. thick) Gasket Kit - Flange Element (Contains AP6708-9, AP6614J, AP10363 & Screws) Gasket Kit - Flange Element (Contains AP6708-9, AP6614J, AP10363 & Screws)
CASE QTY
-- -- -- -- 6
CASE REQ
-- -- -- -- Yes
Adapt-O-Flange Element Conversion Kit
PART NO
UV6830
DESCRIPTION
Adapt-O-Flange Element Conversion Kit
UV6830
WATER HEATER REPAIR KITS
Plumbers Packs are all-inclusive tune up kits for electric water heaters.
Good Plumbers Pack Non-Resistored Elements
PART NO
UV20018
UV2001812PK
CONTENTS
(2) 4500W screw-in elements (2) Element gaskets Upper Therm-O-Disc thermostat Lower Therm-O-Disc thermostat
(2) 4500W screw-in elements (2) Element gaskets Upper Therm-O-Disc thermostat Lower Therm-O-Disc thermostat
UV20018
Better Plumbers Pack Resistored Elements
PART NO
SP20060
CONTENTS
(2) 4500W resistored screw-in elements (2) Element gaskets Upper Therm-O-Disc thermostat Lower Therm-O-Disc thermostat
CASE QTY
--
CASE REQ
--
12
Yes
SP20060
8
W W W. R H E E M . C O M
THERMOSTATS
UV13359
UV13360
UV11695
APCOM Style Thermostats
· Skin packaged with detailed instructions
UV11698
UV11699
UV11700
PART NO
UV13359 UV1335912PK UV13360 UV1336012PK
LOCATION
Upper Upper Lower Lower
TYPE
Non-Simultaneous Non-Simultaneous Non-Simultaneous Non-Simultaneous
THERMOSTAT HIGH LIMIT ADJ RANGE (°F) SETTING (°F)
110 to 160 180
110 to 160 180
110 to 160
--
110 to 160
--
HIGH LIMIT RESET TYPE
Manual Manual
-- --
CONTACT TYPE
SPDT SPDT SPST SPST
VOLTAGE (V)
208,240,277,480 208,240,277,480 120,208,240,277,480 120,208,240,277,480
CASE QTY
-- 12 -- 12
CASE REQ
-- Yes -- Yes
Therm-O-Disc Style Thermostats
· Skin packaged with detailed instructions
PART NO
LOCATION
TYPE
UV11695
Lower Non-Simultaneous
UV1169512PK Lower Non-Simultaneous
UV11698
Upper Non-Simultaneous
UV1169812PK Upper Non-Simultaneous
UV11699
Upper, Lower Simultaneous
UV1169912PK Upper, Lower Simultaneous
UV11700
--
Single
UV1170012PK
--
Single
THERMOSTAT HIGH LIMIT ADJ RANGE (°F) SETTING (°F)
90 to 150
--
90 to 150
--
90 to 150
170
90 to 150
170
90 to 150
170
90 to 150
170
90 to 150
170
90 to 150
170
HIGH LIMIT RESET TYPE
-- -- Manual Manual Manual Manual Manual Manual
CONTACT TYPE
SPST SPST SPDT SPDT SPST SPST SPST SPST
VOLTAGE (V)
120,208,240,277,480 120,208,240,277,480
208,240,277,480 208,240,277,480 208,240,277,480 208,240,277,480
120 120
CASE QTY
-- 12 -- 12 -- 12 -- 12
CASE REQ
-- Yes -- Yes -- Yes -- Yes
Thermostat Covers
PART NO
AP8313-9 AP8314-9
DESCRIPTION
Thermostat Cover - Upper Thermostat Cover - Lower
AP8313-9
AP8314-9
T O P L A C E Y O U R O R D E R C A L L 8 0 0.6 2 1.5 6 2 2, FA X 8 0 0.5 3 5.9 5 3 8
9
GAS WATER HEATER PARTS
IMPORTANT NOTICE: Generally speaking, gas water heater parts are not interchangeable to the same degree as those for electric water heaters. The items below are recommended field stocking items. For service parts information for gas heaters, the recommendation of the OEM should be followed for the specific model and serial number being repaired.
SP8555B
Gas Controls Natural Gas
PART NO
SP8555B
SP20166B
SPECIFICATIONS
Robertshaw - 38,000 BTU/HR / Adjustable 160°F max. 1/2 in. NPT inlet x 1/2 in. inverted flare outlet / 1-1/4 in. shank
White-Rodgers - 38,000 BTU/HR / Adjustable 160°F max. 1/2 in. NPT inlet x 1/2 in. inverted flare outlet / 1 in. shank
SP12258B SP8980B
Gas Controls LP Gas
PART NO
SP12258B
SPECIFICATIONS
Robertshaw - 38,000 BTU/HR / Adjustable 160°F max. 1/2 in. NPT inlet x 1/2 in. inverted flare outlet / 1-1/4 in. shank
Pilot Burner Assemblies
These Pilot Burner Assemblies are for Pre-FVIR models only.
PART NO
SP8980B SP8980C
DESCRIPTION
Pilot Burner Assembly - Natural Gas Pilot Burner Assembly - LP
UV6379R
Thermocouple Kits
Kit contains thermocouple and positioning adapters.
PART NO
UV6379L UV6379R UV6379H UV6379S UV6379T
CAPILLARY TUBE LENGTH (IN)
18 24 30 36 48
BULB LENGTH (IN)
2-11/64 2-11/64 2-11/64 2-11/64 2-11/64
BULB DIA (IN)
3/16 3/16 3/16 3/16 3/16
BULB END CONNECTIONS
Nut, Push-in Clip Nut, Push-in Clip Nut, Push-in Clip Nut, Push-in Clip Nut, Push-in Clip
GAS VALVE END FITTING OD (IN)
11/32 11/32 11/32 11/32 11/32
INSTALLATION ACCESSORIES
UV10351
Flexible Water Connector
Copper flexible water connectors.
PART NO
UV10351 UV10505 UV10506 AP13006
LENGTH (IN)
12 15 18 24
FITTING 1 FITTING 1 FITTING 2 TYPE SIZE - NPT (IN) TYPE
Female
3/4
Female
Female
3/4
Female
Female
3/4
Female
Female
3/4
Female
FITTING 2 SIZE - NPT (IN)
3/4 3/4 3/4 3/4
CONNECTOR TUBE OD (IN)
3/4 3/4 3/4 3/4
MATERIAL
Copper Copper Copper Copper
QTY PACKAGE
2 2 2 1
10
W W W. R H E E M . C O M
INSTALLATION ACCESSORIES
UV12928
Stainless Steel Flexible Water Connectors
PART NO
UV12927 UV12928 UV12929
LENGTH (IN)
12 15 18
FITTING 1 FITTING 1 FITTING 2 TYPE SIZE - NPT (IN) TYPE
Female
3/4
Female
Female
3/4
Female
Female
3/4
Female
FITTING 2 SIZE - NPT (IN)
3/4 3/4 3/4
CONNECTOR TUBE OD (IN)
MATERIAL
QTY PACKAGE
3/4 Stainless Steel 2
3/4 Stainless Steel 1
3/4 Stainless Steel 1
AP10350
Flexible Gas Connectors
PART NO
AP10350 AP13014 AP13013
LENGTH (IN)
18 24 48
FITTING 1 TYPE
Female Female Female
FITTING 1 SIZE - NPT (IN)
1/2 1/2 1/2
FITTING 2 TYPE
Male Male Male
FITTING 2 SIZE - NPT (IN)
1/2 1/2 1/2
CONNECTOR TUBE OD (IN)
1/2 1/2 1/2
CONNECTOR TUBE ID (IN)
3/8 3/8 3/8
Water Heater Installation Kits
UV20016
UV20013
Gas Installation Kits
PART NO
WATER CONNECTOR LENGTH (IN)
UV20015
12
UV20016
15
UV2001612PK 15
UV20017
18
KIT CONTAINS
FLEX WATER 3/4" X 2" TEFLON COMP FTNG FLEX GAS
LINE (2) NIPPLE (2) TAPE 7/8" CON
CON
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
GAS LINE TAPE
-- 3 3
--
WIRE NUT (2)
-- -- -- --
CASE QTY
-- -- 12 --
CASE REQ
-- -- Yes --
Electric Installation Kits
PART NO
UV20012 UV20013 UV20014
WATER CONNECTOR LENGTH (IN)
12
15
18
KIT CONTAINS
FLEX WATER 3/4" X 2" TEFLON COMP FTNG FLEX GAS
LINE (2) NIPPLE (2) TAPE 7/8" CON
CON
3
3
3
3
--
3
3
3
3
--
3
3
3
3
--
GAS LINE TAPE
-- -- --
WIRE NUT (2)
-- 3
--
CASE QTY
-- -- --
CASE REQ
-- -- --
T O P L A C E Y O U R O R D E R C A L L 8 0 0.6 2 1.5 6 2 2, FA X 8 0 0.5 3 5.9 5 3 8
11
WATER HEATER PARTS
UV10374
Compression Fittings
PART NO
UV10354 UV10374
PACKAGE TYPE
QTY PER PACKAGE
Skin Package 2
Skin Package 2
FITTING 1 SIZE
FITTING 1
PLUMBING SIZE (IN)
TYPE
FITTING 2 SIZE FITTING 2
NPT (IN)
TYPE
1/2 Compression 3/4 Pipe thread
3/4 Compression 3/4 Pipe thread
MATERIAL
Brass Brass
CASE CASE QTY REQ
---- ----
AP13045
Dielectric Unions
PART NO
AP13045
PACKAGE TYPE
--
AP1304512PK Bulk
QTY PER PACKAGE
1
FITTING 1 SIZE PLUMBING SIZE (IN)
3/4
FITTING 1 TYPE
Sweat
--
3/4
Sweat
FITTING 2 SIZE NPT (IN)
FITTING 2 TYPE
MATERIAL
CASE CASE QTY REQ
3/4 Female pipe Brass/Zinc -- -- thread plated steel
3/4 Female pipe Brass/Zinc 12 Yes thread plated steel
UV8397G SP20003
Nipples Plastic Lined
PART NO
UV8397G UV8397G12PK AP8397N-8
PACKAGE TYPE
QTY PER PACKAGE
Skin Package 2
Skin Package 2
Bulk
1
THREAD SIZE NPT (IN)
3/4 3/4 3/4
LENGTH (IN)
2-1/4 2-1/4
3
HEAT TRAP TYPE
MATERIAL
CASE CASE QTY REQ
-- Zinc plated steel/Polypropylene liner -- --
-- Zinc plated steel/Polypropylene liner 12 Yes
-- Zinc plated steel/Polypropylene liner -- --
Nipples Plastic Lined/Heat Trap
PART NO
SP20003 UV12992 UV1299212PK
PACKAGE TYPE
QTY PER PACKAGE
Skin Package 2
Skin Package 2
Skin Package 2
THREAD SIZE NPT (IN)
3/4 3/4 3/4
LENGTH (IN)
3 3 3
HEAT TRAP TYPE
MATERIAL
CASE CASE QTY REQ
Ball Zinc plated steel/Polypropylene liner -- --
Flapper Zinc plated steel/Polypropylene liner -- --
Flapper Zinc plated steel/Polypropylene liner 12 Yes
UV12992 SP12112S
Drain Valves
PART NO
BODY MATERIAL
SP12112S
Brass
UV12039
Poly
UV1203912PK Poly
SHANK LENGTH
3 2-1/4 2-1/4
HANDLE TYPE
Screwdriver Handgrip Handgrip
TANK FITTING SIZE NPT (IN)
3/4 3/4 3/4
CASE QTY
-- -- 12
CASE REQ
-- -- Yes
UV12039
T&P Valves
PART NO
TEMP SETTING (°F)
SP8346
210
UV6571B
210
UV6571B12PK 210
PRESSURE SETTING (PSI)
150 150 150
CSA DISCHARGE CAPACITY (BTU/HR)
105,000 105,000 105,000
BODY LENGTH (IN)
4-1/4 3-1/4 3-1/4
SENSOR LENGTH (IN)
3 4 4
INLET THREAD SIZE - NPT (IN)
3/4 3/4 3/4
OUTLET THREAD SIZE - NPT (IN)
3/4 3/4 3/4
CASE CASE QTY REQ
---- ---- 12 Yes
UV6571B
12
W W W. R H E E M . C O M
WATER HEATER PARTS
SP11955C
Run-Off Tubes
PART NO
SP11955C SP11956B
CONFIGURATION
Side mount Top mount
END FITTING
3/4 in. NPT 3/4 in. NPT
TUBE LENGTH (IN)
42 8 Vertical / 62 Horizontal
SP11956B AP12933
Dip Tubes
PART NO
AP12933 SP11248R
END FITTING
3/4 in. NPT close nipple Flare
TUBE DIAMETER )IN)
3/4 3/4
TUBE LENGTH (IN)
53 54
SP11248R
AP12938 SP11309C SP11524C SP8371B
Anode Rods Aluminum
PART NO
AP12938
LENGTH (IN)
42
ROD DIAMETER (IN)
0.625
MATERIAL
Aluminum
HEX HEAD SIZE (IN)
1-1/16
Anode Rods R Tech Resistor Magnesium
PART NO
SP11309C SP11526C
LENGTH (IN)
44 44
ROD DIAMETER (IN)
0.7 0.9
MATERIAL
Magnesium Magnesium
HEX HEAD SIZE (IN)
1-1/16 1-1/16
Anode Rods Magnesium
PART NO
SP11524C SP11524Z
LENGTH (IN)
44 58
ROD DIAMETER (IN)
0.840 0.840
MATERIAL
Magnesium Magnesium
HEX HEAD SIZE (IN)
1-1/16 1-1/16
Flexible Anode Rods R Tech Resistor Magnesium
For installations without the overhead clearance normally required for anode rod replacement; consists of four 12 in. sections with flexible linkages.
PART NO
SP8371B
LENGTH (IN)
54
ROD DIAMETER (IN)
0.9
MATERIAL
Magnesium
HEX HEAD SIZE (IN)
1-1/16
T O P L A C E Y O U R O R D E R C A L L 8 0 0.6 2 1.5 6 2 2, FA X 8 0 0.5 3 5.9 5 3 8
13
WATER HEATER PARTS
Water Heater Insulation Blankets
PART NO
SP57/11C SP57/5 SP57/67
DESCRIPTION
Water Heater Blanket R11 3 in. x 48 in. x 75 in. Water Heater Blanket R5 1.5 in. x 48 in. x 75 in. Water Heater Blanket R6.7 2 in. x 48 in. x 75 in.
CASE QTY
4 4 4
CASE REQ
Yes Yes Yes
SP57/67 AP12935 AP12942
RRT-5 AP13044
Drain Pans Plastic
Durable plastic drain pans with 1 in. glue PVC fitting; for electric water heaters only.
PART NO
AP12934 AP12937 AP12935 AP12936
QTY PER PACK
1 1 1 1
DIAMETER - BOTTOM (IN)
20 22 24 26
HEIGHT (IN)
2-3/4 2-3/4 2-3/4 2-3/4
MATERIAL
Plastic Plastic Plastic Plastic
Drain Pans Aluminum
Aluminum drain pans with 1 in. glue PVC fitting; for gas or electric water heaters.
PART NO
AP12939 AP12941 AP12942 AP12940 AP13325
QTY PER PACK
1 1 1 1 1
DIAMETER - BOTTOM (IN)
20 22 24 26 30
HEIGHT (IN)
2-1/8 2-1/8 2-1/8
2 2-1/8
MATERIAL
Aluminum Aluminum Aluminum Aluminum Aluminum
Expansion Tanks
PART NO
RRT-5 RRT-12
DESCRIPTION
RRT Therm-X-Guard expansion tank 2.5 gal. RRT Therm-X-Guard expansion tank 5 gal.
Water Heater Stand
· Durable galvanized steel stand · Recommended for 30-50 gal. capacity gas water heater protection · Easy screw and nut assembly
PART NO
AP13044
AP130443PK
DESCRIPTION
Water Heater Stand 18 gauge 21 in. x 21 in. x 18 in., 650 lb weight limit
Water Heater Stand 18 gauge 21 in. x 21 in. x 18 in., 650 lb weight limit
CASE QTY
--
3
CASE REQ
--
Yes
14
W W W. R H E E M . C O M
NOTES: ____________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________
T O P L A C E Y O U R O R D E R C A L L 8 0 0.6 2 1.5 6 2 2, FA X 8 0 0.5 3 5.9 5 3 8
15
RHEEM NATIONAL CUSTOMER SERVICE
Divison Office: 334.260.1500 Parts, Customer Service, Warranty: 800.621.5622, fax 800.535.9538, email parts@rheem.com Technical Service: 800.HEATER3 (800.432.8373), email techserv@rheem.com Website: www.rheem.com
4744 Island Ford Road Randleman, NC 27317 336.495.6800 336.495.6867 fax www.rheem.com
In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice. 02-10/RT/WP PRO-8357
Acrobat Distiller 8.0.0 (Macintosh)
Related Documents
Rheem Water Heater Parts and Accessories Catalog Comprehensive catalog of Rheem water heater parts and accessories, including electric and gas water heater components, thermostats, elements, connectors, and more. Features product specifications, part numbers, and compatibility information.
Rheem Water Heater Parts and Cross-Reference Guide A comprehensive guide to Rheem water heater parts, including electric and gas models, replacement parts, and cross-reference charts for various series and controls.
Rheem Tankless Electric Water Heaters: Continuous Hot Water Solutions Explore Rheem's range of tankless electric water heaters, offering continuous hot water on demand for residential and commercial point-of-use applications. Features, specifications, and model details for RTE series.
Rheem Electric Tankless Series Water Heaters - Specifications and Applications Comprehensive information on Rheem Electric Tankless Series water heaters, detailing features, applications, dimensions, electrical specifications, and flow rate performance for models RTE 3, RTE 7, RTE 9, RTE 13, RTE 18, and RTE 27.
