What's in the Box
- 1 TIGHT-SEAL BLENDER LID
- 2 HANDLE
- 3 LED CONTROL PANEL
- 4 SUCTION BLENDER FEET
- 5 BLENDER BASE AND MOTOR
- 6 6-STAINLESS STEEL SHARP BLADES
- 7 64-OZ. TRITAN JAR, BPA FREE
- 8 MAX FILL LINE
- 9 REMOVABLE MEASURING CUP
Control Panel Functions
- 10 START/STOP PUSH CONTROL: In standby mode, the indicator is off. Press the button to turn the indicator on. The blender requires a functional button press to start. In working mode, press this button to stop the blender and return it to standby mode.
- 11 PULSE PUSH CONTROL: Press and hold the button; the indicator turns on and the blender starts. Release the button to stop. If held for over 2 minutes, the blender will stop automatically.
- 12 ICE CRUSH CONTROL: Press the button; the indicator turns on and the blender enters ice crushing mode. The blender will stop automatically after 1 minute. The indicator will blink 3 times before turning off. You can pause operation by pressing the button again.
- 13 SMOOTHIE CONTROL: Press the button; the indicator turns on and the blender enters smoothie mode. The blender will stop automatically after 1 minute. The indicator will blink 3 times before turning off. You can pause operation by pressing the button again.
- 14 LOW SPEED CONTROL: Press the button; the indicator turns on and the blender starts at the lowest speed. The blender stops automatically after 2 minutes. The indicator will blink 3 times before turning off. You can pause operation by pressing the button again.
- 15 MEDIUM SPEED CONTROL: Press the button; the indicator turns on and the blender starts at the medium speed. The blender stops automatically after 2 minutes. The indicator will blink 3 times before turning off. You can pause operation by pressing the button again.
- 16 HIGH SPEED CONTROL: Press the button; the indicator turns on and the blender starts at the highest speed. The blender stops automatically after 2 minutes. The indicator will blink 3 times before turning off. You can pause operation by pressing the button again.
[Note] During blender operation, you can automatically switch from one function to the next by pressing that button.
Product Information
Website: www.mcappliances.us
Model: SLT-2208
Customer Service: (877) 246-0990 | Appliance Support@monchateau.us
Key Features
- 1200 Watts of Power
- 64-oz. Tritan Jar, BPA Free
- Versatile use for Smoothies, Juices, Purées, Food Prep, and more
- PULSE Control for precise blending
- 3 Speed Settings: Low, Medium, and High
- SMOOTHIE Control preset function
- ICE Crush Control preset function
- Durable 6 Stainless Steel Sharp Blades
Assembly Instructions
- Before first use, hand wash the Removable Measuring Cup, Lid, Tritan Jar, and Blades with mild soap and a brush. Rinse all parts and dry thoroughly. [Warning] Be careful, blades are very sharp!
- Place the Blender Base on a sturdy horizontal surface. Ensure the four Suction Blender Feet secure the blender in place.
- Assemble all washed parts onto the Blender Base.
- Insert the power plug into a power outlet. The Control Panel will illuminate for 2 seconds then turn off, indicating standby mode. If the blender is not in operation for 3 minutes, it will enter a dormant state. To reactivate, you must unplug and replug the unit, or remove and replace the Jar onto the Blender Base.
- Remove the Lid. Add liquid ingredients first, followed by solid ingredients cut into small pieces, and then frozen ingredients. [Note] This order provides more consistent blending and reduces stress on the motor. Do not exceed the MAX fill line indicated on the Jar. [Warning] Always remove the core from fruits and vegetables and cut them into small pieces. Never use boiling or hot liquids or run the blender empty.
- Place the Measuring Cup and Lid back onto the Blender Jar.
- Press the START/STOP button. Then, select one of the 6 function controls: PULSE, LOW speed, MEDIUM speed, HIGH speed, SMOOTHIE control, or ICE crush control. Press the START/STOP control a second time to stop the blender's operation.
[Warning] Do not run the blender for more than 3 minutes at a time. Always wait until the unit has cooled to room temperature before performing the next operating cycle.
Important Operating Tips
- For quick or delicate blending tasks, press and hold the PULSE control for a few seconds, then release. Repeat as needed until the desired consistency is obtained.
- To add ingredients while the blender is operating, remove the Measuring Cup and add ingredients through the Lid opening.
- When crushing ice or hard food, keep one hand firmly on the Lid.
- [Warning] For each use, the consecutive operation time should be less than 3 minutes. A minimum rest time of 10 minutes is required between two continuous cycles. Allow the blender to cool down to room temperature before performing the next operating cycle.
- To stop the blender during operation, press the START/STOP control at any time.
- Always pour liquids into the jar first, followed by solids, for better blending results and less stress on the motor.
- Some tasks are not efficiently performed by this blender, such as beating egg whites, whipping cream, mashing potatoes, grinding meat, mixing dough, and extracting juice from fruits and vegetables.
- [Warning] The following items should never be placed in the blender as they may cause damage: bones, large pieces of solid frozen food, or tough foods like turnips.
- To Dislodge Food: Use a plastic spatula to help remove food lodged around the blade assembly. [Warning] Only use the spatula AFTER turning the blender OFF. Replace the Lid and Measuring Cup, then continue blending if necessary. Ensure the spatula is NOT inside the Blender Jar before blending.
- When blending is finished, press the START/STOP control and unplug the blender from the electrical outlet.
- Never remove the Blender Jar from the Jar pad until the blender is off. Simply lift the Blender Jar from the Jar Pad.
- Do NOT put hands into the Blender Jar while the blender is plugged in.
- In the event the blender loses power and shuts off, simply unplug the blender, then plug it back in. Press the START/STOP control to power the blender on.
- If the blender has overheated, let it cool down for at least 15 minutes before powering on again.
Warranty Information
1 YEAR LIMITED WARRANTY
Before First Use
Please unpack and wash all parts with warm, soapy water before first use.
