Haswing Electric Trolling Motor

To The Owner

Thank you for choosing a Haswing electric trolling motor. It's designed for the purpose of superior performance, unpolluted and portable use. Enjoy your wonderful moment with Haswing trolling motor.

This owner's manual contains information for proper installation, operation and maintenance. Be sure to thoroughly read and understand the contents before use. If you have any question about the operation or maintenance of your trolling motor, please contact Haswing customer service.

⭐ We welcome any comments on our product improvement.

To avoid hazards and obtain great performance, special signs are noted in the owner's manual and on the product.

• 警告 WARNING: Failure to follow the instruction could cause severe injury or death.

• 注意 CAUTION: Special precautions that must be taken to avoid damage to the motor.

• 注 NOTE: Information that makes the procedures easier and faster.

Contents

1. Product's features
2. Before the operation
3. Installation
   1. Installing the propeller
   2. Mounting the trolling motor
   3. Battery connection
4. How to operate the motor
5. Trouble shooting and solving method
6. Electric circuit diagram
7. Maintenance
8. Warranty and service

Product's features

The Haswing trolling motor features the following components:

• POWER READER
• EXTENDABLE HANDLE
• CONTROL-CASING
• FOLDING KNOB
• ADJUSTABLE DEPTH COLLAR
• TILTING LEVER
• MOTOR BRACKET
• STEERING TENSION SCREW
• CLAMP SCREWS
• MOTOR SHAFT
• DURABLE MOTOR
• PROPELLER

We reserve the right to change parts without notice.

Before the operation

Battery Usage: Use a deep cycle battery for your motor. Improper use of battery would cause damage to the motor. Make sure the motor is off (handle on neutral) before connecting the battery.

Safety: Personal life-jacket is needed at all time. Choose good weather for your outdoor activity.

Operation Precautions:

• Turn the motor off (handle on neutral) to slow down the boat's speed.
• Tilting the motor to prevent impact when entering shallow water areas.
• Beware of swimmers and your surroundings during operation.

Cleaning the motor: Remove sundries from the propeller and wash off the motor, especially after saltwater use.

Installation

1. Installing the propeller

WARNING: Make sure the motor is disconnected from the battery before installing or replacing the prop.

NOTE: Use the propeller wrench supplied or a 7mm wrench for installation. The use of inappropriate tools may cause motor damage.

1. Install the drive pin into the shaft hole and align it with the propeller. The drive pin and the propeller groove must align horizontally. Once the propeller is in place, install the Sacrificial Anode, stainless washer, and nut into the shaft. (figure.1)
2. Hold the propeller to prevent it from revolving and use the propeller wrench to tighten the propeller nut. (figure.2)

NOTE: If you replace or detach the propeller, please follow the above instruction steps and procedure it conversely.

2. Mounting the trolling motor

WARNING: Make sure the motor is battery disconnected during mounting, dismounting, or onshore periods.

Mount the trolling motor on the centerline of the boat and tighten the clamp screws. (figure.3)

3. Battery connection and power reader

WARNING: Make sure the motor is off (handle on neutral) while connecting the battery.

Battery connection: Select a compatible battery. Please use a deep cycle battery for your motor. Improper use of battery would cause damage to the motor. Connect the red motor cable (+) to the positive battery terminal (+) and the black cable (-) to the negative terminal, then fasten it. (figure.4) Put the battery in a ventilated place.

2. Power reader

The motor has a power reader to display a real-time battery level. Full light indicates a full power charge condition. The light will go off when the power continues to decline. Please recharge the battery when it reduces to 20%. (figure.5)

How to operate the motor

1. Tilting the motor

Hold the motor shaft with one hand and depress the tilting lever with the other hand. Adjust the motor to a desired angle, then release the tilting lever to lock it. The motor has 10 tilting levels. (figure.6)

2. Trolling motor handle

This trolling handle has folding and telescoping functions. Adjust the desired control position simply by pulling and pushing the handle. Folding angle: 110°, extended length: 350mm. You can also adjust the folding knob to stabilize the angle position. (figure.7)

3. Speed control

The speed controller is integrated in the handle. It offers 5 levels of forward speed and 3 levels of reverse speed. Turning the handle to the neutral position will shut down the motor from running. (figure.8)

4. Tension the steering

Loosen the steering tension screw, set the motor to a desired direction, and fasten it again. (figure.9)

5. Adjust the motor depth

Steady the motor shaft and set the depth collar to a desired position, then secure it. Loosen the steering tension screw and deploy the motor carefully. (figure.10)

Trouble shooting and solving method

1. Motor fails to run or lack of power

• Make sure the motor cable is connected properly.
• Check if the cable terminals are clean and corrosion-free.
• Make sure the battery is full. Please recharge it when the battery is empty.
• Make sure there is no fishing line or weeds caught up in the propeller. Please detach and clean up the propeller if there are sundries caught inside the prop. WARNING: Make sure the motor is disconnected from the battery.

2. Hard to steering

• Check if the steering tension screw is loosened.
• Clean the motor shaft and apply lubricant to the fasteners and turning parts.
• Make sure the underwater condition is fine and nothing blocks the way.

3. Motor vibration

• Make sure the propeller is installed properly.
• Inspect the propeller and the drive pin conditions; replace if necessary.
• Disconnect the battery cable and examine it by turning the propeller manually. The motor shall turn freely with a slight magnetic drag. Internal damage might occur if the motor is blocked or locked. Stop use and contact customer service.

For all other malfunctions not listed above, please contact Haswing customer service center.

Electric circuit diagram

The electric circuit diagram shows the connections between the motor and the battery:

Motor:

• RED wire
• GREEN wire
• YELLOW wire
• BLACK wire

Battery:

• RED wire (+)
• BLACK wire (-)

Connections: RED motor cable to positive battery terminal (+), BLACK motor cable to negative battery terminal (-).

Maintenance

1. Please wash and clean the motor and propeller intensively after use as per manual. Damage caused by improper use, surface corrosion, or other issues is not covered by the warranty. (Refer to P.2)
2. Clean up all sundries on or inside the propeller after every use. (Please see P.2 "cleaning the motor")
3. Apply lubricant to the turning parts regularly and use a proper tool to fasten the parts.
4. Apply rust prevention to the cable and battery terminals after every use.
5. Store the motor in a well-ventilated place and keep it dry.
6. To avoid hazards, do not use the motor in intricate water.
7. Do not crash or put heavy things on top of the motor.

This motor is designed for outdoor amusement only. Continuous long-distance transport is not permitted.