Anker SOLIX EverFrost 2 58L Electric Cooler

What's in the Box

• Anker SOLIX EverFrost 2 58L Electric Cooler
• Car Charging Cable
• AC Adapter and Charging Cable
• Wheel Holder (x2)
• Battery Compartment Drawer
• Important Information leaflet

Overview

Diagram showing the Anker SOLIX EverFrost 2 58L Electric Cooler with numbered components. The numbers correspond to the following parts: 1 Cooler Cover, 2 Circulating Fan, 3 Tray Table, 4 Bar, 5 Bottle Opener, 6 Interactive Icon, 7 Display, 8 Handle, 9 Main Battery, 10 Accessory Container / Secondary Battery, 11 Battery Cover, 12 Input Ports, 13 Wheel, 14 Wheel Holder.

The Tray Table has a load capacity of 30 kg (66 lb). The Bar is designed for accessories like rod and knife racks, and tabletops. To attach accessories, align the protruding strip at the back of the accessory with the notch on the bar and insert it fully. Refer to the accessory instructions for details. Accessories can be purchased separately.

Installing the Battery

If a battery is already installed, skip this step. The cooler can accommodate one or two batteries. If using a single battery, install it in the right battery compartment. Ensure no objects are placed in the empty compartment to prevent contamination of battery contact pins, which could lead to poor contact or a short circuit.

Diagrams illustrate the battery installation process: 1. Open the battery cover. 2. Place the battery inside. 3. Push the battery until it clicks, indicating successful installation. 4. Close the battery cover. When the cooler is powered on, the screen will display "Battery Connected." To remove the battery, lift its handle.

Using Your Cooler

Important Tips for Using the Circulating Fan

• Do not insert fingers or other objects into the fan cover.
• Adult supervision is required for children using this product.
• Do not cover the fan surface when using the air-cooling function, as this can lead to poor motor performance and reduced cooling.
• Do not disassemble the fan cover. If disassembly is necessary under special circumstances, ensure the cooler is powered off.

Powering On/Off

To ensure reliable compressor operation after long transportation, place the cooler flat for three hours before turning it on for the first time. Ensure the cooler is connected to mains power via a charger or has a battery installed before powering on.

Before first use, recharge the cooler to activate it.

Press the [Power Button] for 3 seconds to turn your cooler on or off.

Screen Guide

Diagram of the cooler's display screen with numbered indicators: 1 Protective Voltage (M/H/L), 2 Eco/Smart/Max Mode, 3 Fault Code*, 4 Zone A Temperature, 5 Zone B Temperature, 6 Battery Level of Secondary Battery, 7 Child Safety Lock (Press the [Child Safety Lock Button] once to toggle), 8 Wi-Fi / Bluetooth indicator, 9 Max Mode icon (appears only in Max mode), 10 Battery Level of Main Battery.

Fault Codes and Fault Types

Using the App

Connecting the Cooler

1. Connect to Wi-Fi and download the Anker app to remotely control your cooler.
2. Once powered on, the cooler's Bluetooth activates automatically. Turn on Bluetooth on your phone and add the cooler in the app.
3. Upon successful addition, the Wi-Fi/Bluetooth icon on the cooler's screen will turn steady white.
4. To turn Bluetooth on/off, press the [Bluetooth Button] for 2 seconds.

Connecting to Wi-Fi is recommended for a better experience. After a successful Wi-Fi connection, the Wi-Fi/Bluetooth icon changes from [Bluetooth Icon] to [Wi-Fi Icon].

Installing Firmware Updates

You will receive a notification before updates are installed. The cooler must be charging and connected to Wi-Fi or Bluetooth to complete the update. If a battery is installed, its level must be above 1%.

Settings

You can set the temperature, zone, and mode via the app or directly on the cooler.

Setting the Temperature

Press the [A Button] once to enter temperature settings for Zone A. Press the [B Button] twice to enter temperature settings for Zone B. Use the [Up Arrow Button] and [Down Arrow Button] to adjust the temperature. Confirm the temperature by pressing the [OK Button].

Setting the Zone

Press the [Settings Button] to enter the Settings page. Press the [Navigation Buttons] and the [OK Button] to select zones. Press the [Zone Button] to turn Zone A and Zone B on or off.

Important Notes:

• Never set the temperature at 0°C or below when glass bottles are inside the cooler to prevent freezing, which could cause bottles to break.
• Cool hot food only after it has cooled down. Otherwise, the internal temperature will rise, affecting other food's freshness and increasing power consumption.

Setting the Mode

Press the [Settings Button] to enter the Settings page. Press the [Navigation Buttons] to navigate and select Mode. Choose between Eco, Smart, or Max modes and press the [OK Button] to confirm.

• Eco Mode: The quietest mode, saving the most energy for the longest battery life. It stops the air-cooling fan to conserve power, but cooling speed may be slower.
• Smart Mode: The default mode. It uses integrated Negative Temperature Coefficient (NTC) sensors to detect internal and external temperatures, optimizing compressor and fan function for a balance between cooling performance and energy efficiency.
• Max Mode: Activates the cooling fan to circulate cool air and uses maximum power for cooling. This mode reduces battery life and should be used only when needed.

For safety, the cooling fan automatically pauses when the cooler cover is opened.

Powering Your Cooler

AC Power

Power the cooler by connecting it to a wall outlet using the AC charging cable.

Car Power

Connect the cooler to a car's output port using the car charging cable.

Car Battery Protection Grades: The cooler offers three levels of battery protection (Low, Medium, High). To adjust, press the [Voltage Selection Button] to choose Protective Voltage, confirm with the [OK Button], then press the [Voltage Level Selection Button] to choose between "L/M/H", and confirm the level with the [OK Button]. When connected to a car battery (lead-acid), this protection prevents over-discharging.

If the cooler has no battery and the car's battery voltage is lower than the set value, the cooler will stop working. If the car's battery voltage recovers to the required level, the cooler will resume its previous state. If the cooler has a battery and the car battery voltage is low, the cooler switches to its own battery power without shutting down.

Note: To avoid accidental triggering, disable the battery protection function when powering via a car.

USB-C Power

Note: The USB-C cable and charger are not included in the package. Power the cooler by connecting it to a wall outlet with a USB-C cable.

Solar Panel Power (100W Max, 12V-30V)

This power method is only usable when the battery is installed in the cooler.

To protect the compressor's lifespan, the cooler will only operate during solar charging if the battery level is at least 5%.

Power the cooler by connecting it to a solar panel with an XT60 cable.

Maintenance Best Practices

• Turn off all power before cleaning for safety.
• Clean after disassembly and reassemble in reverse order. Avoid excessive force to prevent component damage.
• Use a soft cloth with a neutral detergent for wiping. Do not use scouring powder, benzene, hydrochloric acid, hot water, coarse brushes, abrasives, or hard objects, as they may damage or corrode the cooler.
• Regularly clean the interior and exterior with a damp cloth.
• Never use running water or immerse the cooler in water.
• Ensure air inlets and outlets are free of dust and dirt for proper ventilation and heat dissipation.
• After cleaning, check the power cord for damage or moisture and ensure the plug is not overheated. Verify all connections before supplying power.
• Dry the cleaned cooler with a soft dry cloth or sponge before connecting power to prevent water or liquid in electrical components, which could cause electric shock or short circuits.
• Place the cooler on a level surface for use. A tilt angle exceeding 30° may affect compressor operation.

FAQ

1. What type of battery does the cooler use?
   LFP (Lithium Iron Phosphate) battery.
2. Can the cooler be connected to the solar panel without the battery?
   No. The cooler requires a battery to be installed when a solar panel is connected; otherwise, it will not work.
3. Is there anything to be aware of when using the cooler for the first time?
   It is recommended to lay the cooler flat for three hours before turning it on for the first time.
4. When a battery is in the cooler, does the external power supply prioritize charging the battery or supplying power to the cooler?
   The external power supply will prioritize charging the cooler.
5. Can the cooler be transported for long periods?
   Yes. Ensure the cooler is laid flat for three hours before turning it on after long transportation.
6. What's the maximum load capacity of the bar?
   It is 30 kg / 66.1 lb.
7. Is it normal to have a smell when I first use the cooler?
   Yes. Foaming agents used during production for thermal insulation may leave a slight, harmless residual smell. Before first use, place the cooler in a well-ventilated area with the cover open.

Specifications

Default Exposed Network Interfaces and Services

Bluetooth Low Energy (BLE) Status: When the equipment is not yet connected to a network, it will automatically enable BLE broadcasting and activate BLE services to provide Bluetooth network configuration capabilities.

Note: During the BLE configuration process, ensure your network environment is stable and follow the instructions to complete the setup.

Warranty Policy

3-Year Limited Warranty

Detailed warranty information is available by scanning the provided QR code.