Pro-Ject CD Box RS2 T

Introduction

Dear music lover, thank you for purchasing a Pro-Ject Audio Systems CD player. In order to achieve maximum performance and reliability, you should study these instructions for use carefully.

⚠ Warning of a hazard for the user, the unit, or possible misuse. [Important notice]

Safety Instructions

Laser Diode and Disc Handling

☞ Caution! Laser diode. Refer all servicing to qualified personnel.

This product contains a laser diode. If a disc is cracked, chipped, warped, or otherwise damaged, do not attempt to play it, as this could damage the unit. This player is designed for use with fully circular, full-size CDs only. The use of shaped discs is not recommended. The manufacturer and distributor disclaim all liability arising in connection with the use of damaged or shaped discs.

General Safety Precautions

AC outlet voltages vary from country to country. Before connecting to the mains, ensure that the voltage in your area meets the voltage requirements printed on the power supply.

The power supply is used to disconnect the unit from the mains. Ensure that the power supply is easily accessible at all times.

Never handle the device or the power supply with wet or damp hands.

Avoid letting liquids enter the device or the power supply. Never place any item containing liquid, such as a flower vase, on or near the device. Never spill any liquid on the device or the power supply.

Never place any naked flame sources, such as lighted candles, on or near the device.

The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool, or any other similar conditions.

Connectors

Make all connections while the CD player is disconnected from the power supply. Never use any other power supply than the one supplied with the unit, except for a suitable Pro-Ject Power Box RS device.

Available Connectors:

• Coax S/PDIF
• Opto S/PDIF
• AES/EBU
• I2S
• Power 20V =

(Details of manufacturer address and CE mark are present in the original diagram but not transcribed as per instructions to focus on relevant text.)

Connections

Connection to an External D/A Converter

Use one of the available S/PDIF outputs (Coaxial, Optical, and AES/EBU) or I2S to connect the CD player to a D/A converter or AV processor.

The I2S connection is intended for connection with the Pre Box RS2 Digital only. It includes the master clock from the DAC and ensures the best possible performance.

Mains Power Connection

Connect the low voltage plug from the power supply to the "Power 20V" socket of the unit before connecting the power supply to the mains.

Operation

Inserting and Removing a Disc

Open the top lid and remove the magnetic clamp. Insert the disc with the label side facing upwards, place the magnetic clamp on the disc, and close the lid. After "Reading", the display shows the total number of tracks on the disc and the total duration. The unit must be powered on for disc loading.

Front Panel Controls

The unit features a lever switch on the front panel to turn the power on or off. A blue LED on the front panel illuminates when the unit is on.

You can put the device into standby mode or turn it on again using the remote control. For remote operation, the lever switch must be in the up position.

Dimming the Display

Use the "mode" button on the remote control to change the display brightness. There are 10 steps and two display schemes: Black background with white font, and white background with black font.

Playback Controls

• Play: ► [Play]
• Pause: ►► [Pause]
• Stop: ■ [Stop]

Stepping Between Tracks

The display shows the track number, the elapsed time of the current track, and the step icon as you navigate.

Use the [Previous Track] ◄◄ and [Next Track] ►► buttons.

Scanning Through the Disc

Use the [Rewind] ◄◄ and [Fast Forward] ►► buttons to scan through the disc.

Remote Control Functions

The power button 💠 [Power] on the remote turns the unit on or back to standby. The lever switch must be in the up position.

Selecting Tracks

Buttons 1 through 9 and 0 allow direct access to specific tracks and start playback. For example, to play track 19, press "0" or "No", then "1", and then "9".

Repeat and Random Play

• "Repe": 🔁 [Repeat Current Track]
• "Repe": 🔁 [Repeat All Tracks]
• "Shuff": 🔀 [Shuffle Play]

Other Buttons

• "Mode": Adjusts brightness and display scheme (refer to the "Dimming the display" chapter).
• "No": Used for direct access to tracks 10 and above.
• "Mute": Engages/disengages mute on compatible Pro-Ject devices like the Pre Box RS/RS2 Digital, MaiA DS/DS2, or similar.

Maintenance

Replacing Batteries

Proceed as follows:

• Unscrew the 4 screws on the back side of the remote and remove the back cover.
• Replace the battery, ensuring it is inserted with the correct polarity.
• Reattach the back cover and screw all screws back in.

Battery type: 1 x CR2032 / 3V or 1 x CR2025 / 3V.

Do not dispose of batteries as ordinary domestic refuse. Please dispose of exhausted batteries at appropriate collection sites, usually located at supermarkets and drugstores.

Technical Specifications

Service

Should you encounter a problem that you cannot alleviate or identify, please contact your dealer for further advice. If the problem cannot be resolved there, the unit should be sent to the responsible distributor in your country.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use. Modification or changes to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer.

Copyright and Trademarks

Pro-Ject Audio Systems is a registered Trademark of H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems.

Copyright © 2019. All rights reserved.

The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.

TOSlink® is a registered trademark of Toshiba corporation. HDMI is a trademark of HDMI Licensing Administrator, Inc.

Waste from Electrical and Electronic Equipment (WEEE): This directive mandates the collection and recycling of electronics and component materials to reduce the amount going to landfills. Outside North America, when the user decides to discard this product, it must be sent to a separate collection facility for recycling. Please contact your point of purchase for more details.