Pro-Ject X8 Turntable Setup Guide

Getting Started

• Ensure sufficient space for unpacking your turntable.
• Always unpack and set up in a clean environment.
• Do NOT throw away the packaging. Retain it for service or returns. Damage due to alternative packaging may affect refunds.
• Refer to the complete manual at: www.project-audio.com/en/product/x8

Setup Steps

1. Step 1: Unpack Accessories

   Unpack all items from the accessory bag: felt mat, gloves, Allen key, antiskating weight, single adapter, drive belt, and cartridge alignment protractor.

2. Step 2: Remove Dust Cover Carton

   Remove the dust cover carton from the box.

3. Step 3: Lift Turntable

   Carefully lift the wrapped turntable out of the box.

4. Step 4: Unpack Connect it E Cable

   Unpack the Connect it E phono cable.

5. Step 5: Unpack Counterweight

   Unpack the counterweight.

6. Step 6: Unpack Power Supply

   Unpack the power supply unit.

7. Step 7: Unpack Platter

   Unpack the platter.

8. Step 8: Unpack Turntable

   Unpack the turntable unit.

9. Step 9: Connect Phono Cable

   Connect the phono cable (Connect it E) to the turntable. The connector is located under the tonearm base. Ensure the connector is aligned with the plug.

10. Step 10: Remove Protection Caps

    Remove the protection caps from the spindle and platter.

11. Step 11: Mount Platter

    Carefully place the platter onto the spindle.

12. Step 12: Align Platter

    Ensure the platter is properly aligned on the spindle.

13. Step 13: Check Level

    Check if the turntable is level. A spirit level is recommended (available separately).

14. Step 14: Adjust Feet

    Adjust the turntable's feet if necessary to ensure it is perfectly level.

15. Step 15: Install Drive Belt

    Place the drive belt onto the motor pulley and around the platter.

16. Step 16: Remove Tonearm Tie

    Remove the twist tie securing the tonearm.

17. Step 17: Install Counterweight

    Screw the counterweight onto the rear of the tonearm.

18. Step 18: Remove Stylus Protection

    Remove the protective cap from the stylus.

19. Step 19: Place Mat and Record

    Place the felt mat on the platter, then place a record on top of the mat.

20. Step 20: Position Tonearm

    Carefully place the tonearm between the platter and armrest, and lower the tonearm lift.

21. Step 21: Balance Tonearm

    Balance the tonearm by turning the counterweight forward or backward on the rod until the tonearm floats level. Place the tonearm back on its rest and raise the tonearm lift.

22. Step 22: Set Counterweight Dial to Zero

    Hold the counterweight steady and set the dial to '0' by turning only the dial to align with the marker on the tonearm.

23. Step 23: Set Tracking Force

    Turn the entire counterweight counterclockwise until the scale reads 23 (this sets the tracking force).

24. Step 24: Attach Antiskating Weight

    Put the loop of the antiskating weight into the outer groove on the tonearm post.

25. Step 25: Connect Power Supply

    Connect the power supply unit to the turntable.

26. Step 26: Power On and Select Speed

    Turn on the motor using the switch located on the front left under the chassis. Select the desired speed by pushing the button.

27. Step 27: Connect to Hi-Fi System

    Connect the turntable to your hi-fi system and enjoy your music!

Service and Warranty

If you encounter a problem that cannot be resolved with the provided information, contact your dealer. If the issue persists, the unit may need to be sent to the responsible distributor. Warranty repairs require the unit to be returned in original packaging. Please retain all original packaging, including inserts, for potential service or returns. Never return a record player without ensuring it is safely disassembled and correctly packaged according to the diagrams in the user guide. Remove and pack separately: lid, counterweight, anti-skating weight, and belt. Fit the cartridge protection cap and tonearm transport lock before packaging.

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modifications or changes to any part of the product by unauthorized persons release the manufacturer from any liability over and above the customer's lawful rights.

Warranty: Terms and Conditions

• A warranty is valid only for products purchased from an authorized Pro-Ject Audio Systems retailer or dealer.
• This warranty offer is limited to the repair of the equipment (which could be a repair or replacement at our discretion, neither of which affects your original warranty).
• Neither transportation or any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty.
• A warranty is only valid for the original owner. It is not transferable.
• To validate your warranty, you will need to provide the original sales invoice or other proof of ownership and date of purchase.
• Warranty must be claimed within two years of purchase from an authorized dealer. After this period of time, the warranty will expire.
• The legal warranty obligation exists in addition to this warranty and is not limited by this warranty.

Warranty Exclusions:

• Deterioration of component parts that wear out with use, such as batteries, headphone ear pads, drive belts, and cartridges.
• Damages caused by incorrect installation, connection, or packing.
• Damages caused by any use other than the correct use described in the user manual, negligence, modifications, or use of parts not made or authorized by Pro-Ject Audio Systems.
• Damages caused by faulty or unsuitable ancillary equipment.
• Damages caused by accidents, lightning, water, fire, war, public disturbances, or any other cause beyond the reasonable control of Pro-Ject Audio Systems and its appointed distributors.
• Products where the serial number has been altered, deleted, removed, or made illegible.
• Repairs or modifications executed by an unauthorized person.

Commercial Use:

Faults caused due to using domestic products in commercial environments or on a commercial scale are not covered by warranty. This turntable is intended for domestic use only. Using it for business applications is done at your own risk.

Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.

Copyright © 2021. All rights reserved.