Lenovo thinkplus Bone Conduction Bluetooth Headphone X7 User Manual

Product Overview

This manual provides instructions for using the Lenovo thinkplus Bone Conduction Bluetooth Headphone X7. Please read this manual before use.

Product Model: Lenovo X7

Product Material: ABS+PC

Bluetooth Version: V5.3

Battery Capacity: 150mAh

Rated Input: 5V 150mA

Charging Time: About 2 hours

Running Time: About 10 hours

Rated Power: 0.75W

(All technical information is subject to actual performance)

List of Articles

• Earphone x1
• Charger cable x1
• Manual x1

Product Usage Profile

Power On/Off

• Power On: Long press the multifunctional button for about 2 seconds. The blue light will turn on for 1 second.
• Power Off: Long press the multifunctional button for about 4 seconds. The red light flashes twice and then powers off.

Bluetooth Connection

After the headset is turned on, turn on your smart device and enable Bluetooth. Search for "联想 thinkplus-X7" (Lenovo thinkplus-X7) and click to connect. The red and blue lights will turn off upon successful connection.

Charging

• Charging Diagram: The device features a magnetic charging port.
• Charging Indication: When charging, the indicator light will be red. When the battery is full, the indicator light will be off.
• Charging Instructions: After normal connection, the smart device will display the earphone's power level. If the battery is low, connect the charging cable using a marked 5V charger.
• Note: If there is sweat attached to the charging post, please wipe it clean before charging.

Functional Operation

• Next Song: Double click the multifunctional button.
• Previous Song: Double click the minus key.
• Volume Up: Short press the multifunctional button.
• Volume Down: Short press the minus key.
• Activate Voice Assistant: Triple click the multifunctional button.
• Answer Call: Double click the multifunctional button.
• Hang Up Call: Long press the multifunctional button for 2 seconds.
• Play/Pause: Long press the multifunctional button for 1 second.

Indicator Description

• Alternating red and blue: Pairing state.
• Red and blue lights out: Paired state.
• Red light is steady on: Charging.
• Blue light is on: Successful connection.

Product Operation Instructions

• Do not attempt to disassemble or replace any parts within the product unless specifically indicated in the instructions.
• Do not immerse the product in water or any other liquid, as it is not waterproof.
• If any liquid accidentally enters the product, disconnect and remove it immediately.
• Ensure your hands are dry when installing or removing the product to avoid electric shock.
• Do not place the product near heat sources or expose it directly to fire.
• Avoid placing the product in environments with strong electromagnetic forces, as this may cause malfunction.

Product Specifications

(All technical information is subject to actual performance)

Name and Content of Harmful Substances in Products

This form is prepared in accordance with the requirements of SJ/T11364.

Pb (Lead)

• Printed circuit module: X
• Shell and other small structural parts: O

Hg (Mercury)

• Printed circuit module: O
• Shell and other small structural parts: O

Cd (Cadmium)

• Printed circuit module: O
• Shell and other small structural parts: O

Cr(VI) (Hexavalent Chromium)

• Printed circuit module: O
• Shell and other small structural parts: O

PBB (Polybrominated Biphenyls)

• Printed circuit module: O
• Shell and other small structural parts: O

PBDE (Polybrominated Diphenyl Ethers)

• Printed circuit module: O
• Shell and other small structural parts: O

Legend:

• O: Indicates that the content of the hazardous substance in all homogeneous materials of the component is below the limit requirements specified in GB/T26572.
• X: Indicates an excess of the hazardous substance in at least one homogeneous material of the component, exceeding the limit requirements specified in GB26572.

The components marked "X" are due to global technological development limitations that prevent the substitution of hazardous substances.

Electronic and electrical products sold within the People's Republic of China must display a logo indicating the environmental protection use period of the product under normal service conditions.

Warranty Statement

This document provides the following warranties for the products attached:

If the product is damaged due to quality defects under normal use within twelve (12) months from the date of purchase (the "Warranty Period"), it will be repaired free of charge. If the manufacturer confirms it cannot be repaired, it will be replaced free of charge. Products repaired or replaced will continue to be covered by the warranty for the remaining warranty period (not less than 30 days).

The purchase date is based on the sales invoice date. If the purchase date cannot be determined, the warranty period will be calculated from the date of manufacture for thirteen (13) months.

To apply for warranty, please call the product service hotline first and follow the provided instructions. You will need to provide an accurate, complete, and clearly filled-out valid sales invoice.

The above warranties do not apply to the following situations:

1. Exceeding the validity period of the three-package warranty.
2. Tampering with the warranty card, or inconsistency between the product code and the product itself.
3. Failures or damage caused by misuse, abuse, or improper transportation, use, maintenance, or storage.
4. Failures or damage caused by force majeure (such as earthquakes, wars, fires, etc.) or accidents.
5. Damage to zippers or buckles due to excessive force.
6. Seams or tears caused by excessive load.
7. Any damage caused by sharp objects.
8. Products showing signs of burning or water immersion.
9. Damage caused by unauthorized disassembly or modification.
10. Aging, discoloration, wear, breakage, and other losses occurring during the normal use of the product.
11. This warranty will be void if the original identification label of the product is altered or damaged. The completeness and appearance of the product and accompanying materials are not covered by the warranty; you should inspect the product upon receipt and raise any objections to discrepancies.

The above warranties are the sole warranties made by Lenovo regarding the products and are applicable only within mainland China. Nothing in this document affects consumer rights that cannot be excluded or limited by law.

After-sales email: frank@szeysan.cn

Service phone: 400-812-0102

" " " " and other Lenovo logos are trademarks of Lenovo Group. Other trademarks, company names, products, or service names mentioned in this material may be trademarks of Lenovo Group or other companies.

Copyright 2023 Lenovo Beijing Co., LTD. All rights reserved.

Disclaimer

This user manual provides no warranty, representation, or other implication of any kind. The products, specifications, and information mentioned are for reference only and are subject to change on the website at any time without prior notice.