Pinta Step Light Installation Instructions

Product Specifications

Dimensions

HV2902 + HV2904 Series: Features an outer diameter of approximately 100mm, a depth of approximately 30mm (with a noted 22mm dimension), and a mounting hole diameter of approximately 82mm.

HV2905 Series: Features an outer diameter of approximately 100mm, a depth of approximately 30mm, and a mounting hole diameter of approximately 82mm.

Note: Specific dimensions are detailed in the original product diagrams.

Mounting Base Diagram Description

The mounting base diagram illustrates a circular base with an outer diameter of approximately 82mm. It includes a central opening of approximately 30mm diameter. Various measurements indicate screw hole positions and clearances, such as 12mm, 15mm, 18mm, 20mm, and 30mm from the center or edge, facilitating secure installation.

Important Safety Issues

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w.
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• When installing low voltage fittings, voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25 m from the LED Driver; if not within this allowance, warranty will be voided.
• Aluminium and 304SS fittings must not be installed within 2 km of any salt water environments.
• When installing copper fittings, gloves must be worn to avoid any oils transferring to the fitting.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining).
• All o-rings and seals must be in place correctly to maintain warranty.
• These instructions may be updated at any time due to product improvements. Please visit the website for the most current installation instructions.

Steps for Installation for HV2902 Models

1. Make sure that the electrical circuit is free of voltage (master switch off).
2. Remove screws from the front of the fitting and set them aside.
3. Install the base plate in the desired location.
4. Using an appropriate 12v LED Driver or transformer - DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V.
5. Connect the cable into the terminal block: Positive from the cable run to the positive of the fitting, then connect the neutral. If more than one fitting is installed, wiring must be done in parallel.
6. Insert the globe into the fitting, making sure the globe can be used with the selected driver.
7. Reattach the face onto the fitting, making sure seals are still in place and screws are tight to avoid water penetration into the fitting.
8. Apply silicone around the edge of the fitting to prevent any water from getting inside to the electrical connections.
9. All connections must be carried out carefully; inspect all contacts before switching back on the electric circuit.

Steps for Installation for HV2904 + HV2905 Models

1. Make sure that the electrical circuit is free of voltage (master switch off).
2. Remove screws from the front of fitting and set them aside.
3. Using an appropriate 12v LED Driver - DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V.
4. Connect the cable. If more than one fitting is installed, wiring must be done in parallel.
5. Strip back the cable on both the fitting and the cable run and twist the positive cables together. Then connect the neutral cables together.
6. Solder all joins using solder and either a heat gun or butane gas torch.
7. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
8. Heat the heat shrink or crimp the gel cap, making sure all connections are covered.
9. Install the base plate in the desired location.
10. The fitting is preset to 3000K. To change, move the switch above the PCB to the desired colour temperature.
11. Reattach the face onto the fitting, making sure seals are still in place and screws are tight to avoid water penetration into the fitting.
12. Apply silicone around the edge of the fitting to prevent any water from getting inside to the electrical connections.
13. All connections must be carried out carefully; inspect all contacts before switching back on the electric circuit.

Contact Details

Address: 143 Beauchamp Road, Matraville NSW 2036, Australia

Tel: 02 9381 8300

Fax: 02 9666 8881

Email: sales@havit.com.au

Web: www.havit.com.au

Warranty Terms & Conditions

Refer to the website for full warranty terms and conditions.

Additional Information

Model series covered: HV2902 + HV2904T, HV2902-AB + HV2904T-AB, HV2905T-12V.