Cooler Master TD500 MAX PC Case
Make It Yours.
Package Contents
CASE Components
| Figure | Name | Qty | Used for |
|---|---|---|---|
| [A] | #6-32*6mm screw | 13 | Motherboard & other |
| [B] | SSD Mounting pin | 12 | Installing SSD toollessly |
| [C] | SSD Dampening Pads | 12 | Installing SSD toollessly |
| [D] | Stand-off socket tool | 1 | Motherboard stand-off installation |
| [E] | HDD Bracket | 4 | Installing HDD toollessly |
| [F] | Cable Tie | 10 | Cable management |
PSU Components
| Figure | Name | Qty | Used for |
|---|---|---|---|
| [G] | AC Power Cord | 1 | Connect to outlet |
| [H] | 8pin 2nd stage Cable | 1 | Motherboard 8pin CPU |
| [I] | 4+4pin 2nd stage Cable | 1 | Motherboard 4+4pin CPU |
| [J] | 6+2pin 2nd stage Cable | 1 | GPU 6+2pin PCIE |
| [K] | 24pin 2nd stage Cable | 1 | Motherboard 24pin port |
COOLING Components
| Figure | Name | Qty | Used for |
|---|---|---|---|
| [L] | Intel 115x/1200/1700 Backplane | 1 | Intel 115x/1200/1700 |
| [M] | Intel Bracket | 2 | Intel 115x/1200/1700 |
| [N] | AMD Bracket | 2 | AMD AM4/AM5 |
| [O] | Thermal Paste | 1 | CPU heat dissipation |
| [P] | Φ8*8 M3 nut | 4 | Lock Intel & AMD Socket |
| [Q] | Bracket Screw | 4 | Lock Intel & AMD Bracket |
| [R] | AMD Screw | 4 | AMD AM4/AM5 |
| [S] | Intel 1700 Screw | 4 | Intel 1700 |
| [T] | Intel 1200/115x Screw | 4 | Intel 1200/115x |
| [U] | 3 to 1 Fan Splitter | 1 | Connect multiple fans |
| [V] | Water pipe clamp | 2 | Fixed water pipe |
Compatibility
The case supports ATX, Micro-ATX, and Mini-ITX motherboards.
Maximum CPU cooler height: 165 mm
Maximum graphics card length: 380 mm (when an AIO cooler is pre-installed on the front)
Front I/O & Buttons
The front panel features the following connections:
- 2 x USB-A 3.2 Gen1
- F-PANEL (Front Panel Header)
- AUDIO (Front Panel Audio)
- ARGB Hub
- RESET SW (Reset Switch)
- USB-C 3.2 Gen2 x 2
Basic Installation Guide
-
1. Install Motherboard
Install motherboard standoffs and then mount the motherboard using screws [A] and tool [D]. Connect the necessary power cables: 8-pin CPU cable [H], 4+4-pin CPU cable [I], 6+2-pin PCIe cable [J], and the 24-pin motherboard cable [K].
-
2. Install Cooling Head (CPU Cooler)
For Intel LGA 1200/115X/1700 Sockets: Attach the backplane [L] to the motherboard. Secure the Intel bracket [M] or Intel 1700 bracket [L] using screws [Q] and nuts [P]. Apply thermal paste [O] to the CPU. Mount the CPU cooler block and secure it.
For AMD AM4/AM5 Sockets: Attach the AMD bracket [N] to the motherboard. Secure using screws [R] and nuts [P]. Apply thermal paste [O] to the CPU. Mount the CPU cooler block and secure it.
Use water pipe clamps [V] as needed for liquid cooling setups.
-
3. Install GPU
Insert the graphics card into the appropriate PCIe slot. Connect the 12VHPWR cable and 6+2pin PCIe power cables as required by the GPU.
-
4. Install 2.5" SSD
Mount 2.5" SSDs using SSD mounting pins [B] and dampening pads [C] in the designated drive bays.
-
5. Install 3.5" HDD
Install 3.5" HDDs using the provided HDD brackets [E] and screws [B].
-
6. Install Case Fans
Mount case fans (up to three 120mm or two 140mm fans at the front, one 120mm fan at the rear) using screws. Connect multiple fans using the 3-to-1 fan splitter [U].
-
7. Install Radiators
Radiators of various sizes (120/140/240/280/360mm) can be installed at the top, front, or rear of the case, respecting clearance limits.
-
8. Connect ARGB and Fan PWM
Connect ARGB LED strips and PWM fans to the motherboard or the ARGB Hub using the provided cables for lighting and fan control.
-
9. Install Side Panel
Attach the side panels to enclose the case and secure all components.
-
10. Plug in the Power Cord
Connect the AC power cord [G] to the Power Supply Unit (PSU) and plug it into a wall outlet.
Specifications
CASE Specifications
| Dimensions (L x W x H) | 499 x 210 x 500mm |
|---|---|
| Motherboard Support | Mini-ITX, Micro ATX, ATX |
| Expansion Slots | 7 |
| Drive Bays | 3.5" HDD: 3, 2.5" SSD: 3 |
| Fan Support | Top: 3 x 120mm / 2 x 140mm Front: 3 x 120mm / 2 x 140mm Back: 1 x 120mm |
| Radiator Support | Top: 360/280/240/140/120mm Front: 360/280/240/140/120mm Back: 120mm |
| Pre-installed Fan(s) | Back: 1 x CF120 ARGB fan |
| Pre-installed Radiator | Front: MasterLiquid 360 Atmos MAX ver. |
| Pre-installed PSU | Bottom: GX II 850 Gold ATX3.0 MAX ver. |
| CPU Cooler Clearance | 165mm |
| Maximum Component Length | PSU Length: 200mm (Pre-installed PSU Length 160mm) Graphics Card: 380mm (with pre-installed AIO on front) |
POWER SUPPLY Specifications
| ATX Version | ATX 12V Ver.3.0 |
|---|---|
| Fan Type | 120mm HDB Fan |
| Efficiency | ≥90% @ Typical Load |
| Operating Temperature | 0~40°C |
| Protections | OPP, OVP, OTP, OCP, SCP, UVP, Surge and Inrush Protection |
| Regulatory Compliance | cTUVus, TUV, CE, FCC, BSMI, CCC, EAC, RCM, UKCA |
| Connectors | ATX 24 Pin: x1 (550mm) EPS 4+4 pin: x1 (500mm) EPS 8 pin: x1 (500mm) SATA: x6 (500(s)+120(s)+120(s)+120(p)mm) Peripheral 4pin: x2 (500(s)+120(s)+120(s)+120(p)mm) PCI-e 6+2 pin: x1 (300mm) 12VHPWR: x1 (650mm) |
| AC INPUT | 100-240V~, 10-5A, 50-60Hz |
| DC OUTPUT | +45V: 20A, +3.3V: 20A, +12V: 70.8A, -12V: 0.3A, +5VSB: 3A |
| TOTAL POWER | 120W (DC Output), 850W (Total Power) |
WATERCOOLING Specifications
| CPU Socket Compatibility | Intel: LGA 1700/1200/1156/1155/1151 / 1150 sockets AMD: AM5/AM4/AM3+/AM3/AM2+/AM2 / FM2+/FM2 / FM1 sockets |
|---|---|
| Radiator | Material: Aluminum Dimensions (L x W x H): 394 x 119.6 x 38.2 mm |
| Pump | Dimensions (L x W x H): 84.9 x 81 x 53.15 mm MTTF (Hours): >210,000 hours Noise Level (dBA): 25 dB(A) Connector: 4-Pin PWM Rated Voltage (VDC): 12V Power Consumption (W): 3.84 W |
FANS Specifications
| Dimensions (L x W x H) | 120 x 120 x 25mm |
|---|---|
| LED Type | Addressable Gen 2 RGB (3 PIN ARGB) |
| Speed (RPM) | 0~2400RPM ± 10% |
| Air Flow (Max) | 75.2 CFM |
| Noise Level (dBA) | 30 dBA |
| Air Pressure (Max) | 3.63 mm H2O |
| MTTF (Hours) | >200,000 hours |
| Power Connector | 4-Pin (PWM) |
| Power Consumption (W) | 2.16W |
| Rated Voltage (VDC) | 12V |
| Rated Current (A) | 0.18A |
Warranty Information
Cooler Master provides a limited hardware warranty for its products. The warranty period varies by product type:
- Computer Cases: 2 years
- Liquid Cooler: 5 years
- Power Supply: 5 years
The warranty covers defects in material and workmanship under normal use. It does not cover damage caused by misuse, accidents, natural disasters, or unauthorized modifications. Please retain your proof of purchase. For detailed terms and conditions, please visit the Cooler Master website.
Contact Information & Support
China: Cooler Master China, Room 112, Building 9, No. 327, Songjin Road, Jinshanwei Town, Jinshan Dist., Shanghai City, China. Tel: +86-21-51872177
Europe: Cooler Master Europe B.V., Lodewijkstraat 1b, 5652AC Eindhoven, The Netherlands. Tel: +31-(0)40-702-0900
North America: Cooler Master NA, 1 N Indian Hill Blvd Suite D200 Claremont, CA 91711 USA. Tel: +1-888-624-5099
South America: E-mail: Soporte_Latam@coolermaster.com.tw
For product information, manuals, and technical support, visit: www.coolermaster.com
