Manuals+
MiCODUS MV710N 2G GPS Tracker User Manual

MiCODUS MV710N 2G GPS Tracker User Manual

Learn how to set up your new MiCODUS Tracker

1. Main Features

  • 2G GSM: Utilizes 2G GSM network for communication.
  • GPS+BDS+LBS+GLONASS: Multi-constellation positioning for accurate location tracking.
  • Remotely Cut Off / Resume Fuel: Ability to remotely disable or enable the vehicle's fuel supply.
  • Realtime Tracking: Continuous monitoring of the device's location.
  • Historical Route Playback: Review past travel routes.
  • Vibration Alarm: Alerts when the device detects vibration.
  • 9-95V Wide Working Voltage: Compatible with a broad range of vehicle power supplies.
  • Anti Jammer: Detects and alerts if a GPS signal jammer is used.
  • Power failure alarm: Notifies if the device's power source is disconnected.
  • Geo-fence: Creates virtual boundaries and alerts when the device enters or exits them.
  • Ignition On/OFF Alarm: Alerts when the vehicle's ignition is turned on or off.
  • Battery low voltage alarm: Notifies when the vehicle's battery voltage is low.
  • Overspeed Alarm: Alerts if the vehicle exceeds a set speed limit.
  • Open Door Alarm: Notifies when the vehicle doors are opened.

2. Specifications

Category Details Specification
Device Information Model MV710N
Weight 31.6g
Dimensions 75mm(L)*26mm(W)*12mm(H)
Battery Built-in 140 mAh 3.7V polymer battery
Working Parameters Working Voltage 9-95V DC
Working Current 12V/average 35mA
Sleep Current 12V/average 10mA
Working Temperature -20°C - 75°C
Working Humidity 10%-85% RH non-condensing
Cellular Specifications SIM Card Micro SIM
Cellular Antenna Built-in, FPC
Working Frequency GSM/2G: 850/900/1800/1900MHz
GNSS Specifications GNSS GPS+BDS+GLONASS+LBS
GPS Frequency L1: 1575.42±1.023MHz
BDS Frequency B1:1561.098±2.046MHz
Sensitivity -162 dBm
Satellite Channels 32
Hot/Cold Start <1s, <32s @ Open Sky
Positioning Antenna Built in ceramic dielectric antenna, 18*18*4mm
Accuracy <10m (1σ)
External Interface ACC Detection 1
Cut Off Fuel/Power Standard
Open door Alarm 1

3. How to Manage the Tracker to Get Online

Step 1: SIM Card Requirements

Please get a suitable SIM card from your local place. The SIM card must meet the following points:

  • It must be compatible with the 2G GSM network.
  • Please enable SMS, call, and internet data traffic for the SIM card.
  • Enable the caller ID display feature.
  • Remove the PIN code from the SIM card.
  • Use a Micro size SIM card for the tracker.
  • Please inquire with your SIM card provider for the exact correct APN information.

SIM Card Types:

  • Nano SIM
  • Micro SIM
  • Normal SIM

Step 2: SIM Card Installation

Install the Micro SIM card into the designated slot on the tracker. After successfully installing the SIM card and ensuring the device is online, attach the cover.

3. Wiring

Connect the tracker's wires to the vehicle's power supply and other components as follows:

  • VCC (+): Connect to the positive terminal of the vehicle's battery (9-95V DC).
  • GND (-): Connect to the negative terminal of the vehicle's battery.
  • ACC: Connect to the vehicle's ignition switch (ACC terminal).
  • MOT: Connect to the vehicle's ignition switch (START terminal) or a relay control wire.
  • LIN: (Not explicitly detailed in wiring, but present on device label).
  • Door Sensor: Connect to the vehicle's door sensor (if applicable).

Note: After installing the SIM card correctly, it is crucial to connect the tracker to an external power supply of no less than 12V for proper operation.

4. Configure APN

Obtain the correct APN name from your local SIM card provider. Take the tracker to a location with a good signal and configure the APN using SMS commands:

Functions Command Format Reply Example Note
APN Setting APN,ApnName,User,Password# SET APN OK APN,orange,orange,orange# Use this command if the SIM card has an APN username and password.
APN,ApnName# SET APN OK APN,internet# Use this command if the SIM card operator does not have an APN username and password.

Note: The APN information must be 100% correct to match the SIM card. Incorrect APN configuration may result in the tracker failing to get online, even if it replies "SET APN OK".

5. Indicator Status Description

LED Event State
CELL LED (YELLOW) Searching for network Flash every 1 second
Network has been registered Solid
GPS LED (BLUE) GPS is in fixing Flash every 1 second
GPS has fixed Solid
ALL LED Device is working but stopped more than 5min ALL LED TURN OFF
Device has not been turned on
Device ran out of battery

6. Package Content

  • GPS Main Unit x 1
  • Function Cable x 1
  • User Guide x 1
  • Genuine Packing Box x 1

7. Functions Explanation

a. Cut Off Fuel / Resume Fuel

Set the center number using the SMS command: CENTER,A,center number#

Send the fuel cut-off/resume command from the center number: RELAY,A#

Where A can be:

  • 0: Resume Fuel
  • 1: Cut Off Fuel Immediately
  • 2: Cut Off Fuel Safely (vehicle speed must be below 20km/h if GPS is fixed, or stationary if GPS is not fixed)

Example: RELAY,1# will cut off fuel immediately.

b. Vibration Alert

This function works under stationary status. To use it:

  • Configure SOS numbers: SOS,A,1st number,2nd number,3rd number# (supports up to 3 numbers).
  • Enable arm mode: ARM#
  • Configure alarm ways: SENALM,[A][,M]#
    • A: ON/OFF (default: OFF)
    • M: Way of alarming (0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default: 1)

Keep the device stationary for over 5 minutes to enter sleep arm mode. Vibrate the device to trigger vibration alarm messages.

c. External Battery Low Voltage Alarm

Command format: LVALM,A,B,M#

  • A: ON/OFF (default: ON)
  • B: Voltage alarm threshold (9-95V, default: 11.1V)
  • M: Way of alarming (0: Server only, 1: SMS+Server, 2: SMS+Server+Call, default: 1)

Example: LVALM,ON,11.5,1# will send an alarm message via server and SMS when the external battery voltage drops below 11.5V.

d. Engine Start and Flameout Alarm

Command format: ACCALM,A,B,M#

  • A: ON/OFF (Default: ON)
  • B: Alarm type (0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC ON&OFF Alarm; Default: 2)
  • M: Way of alarm (0: Server only, 1: SMS+Server, 2: SMS+Server+Call, Default: 1)

Example: ACCALM,ON,2,1# will send an alarm message via server and SMS when the engine starts or stops.

8. Installation Recommendation

General Guidelines:

  • The device should face up to the sky for optimal GPS signal reception.
  • Metal thermal barriers, such as heating layers in windshields, can affect the signal.

Recommended Placement Locations:

For Cars:

  • Under front windshield
  • Inside Door Pedal
  • Around dashboard
  • Under rear windshield
  • Inside the head light
  • Inside the front cover

For Scooters:

  • Inside the taillight component or plastic
  • Under the pedal

9. Troubleshooting

Type Use / Solution
Unable to connect to tracking platform Check the APN and settings. Verify SIM card data service is enabled. Check SIM card balance.
Tracker shows offline Check if external power is still connected. Ensure the vehicle is not in a network blind area. Check SIM card balance.
Unable to locate Ensure the top side faces upward without metallic shielding. Make sure the device is not in an area with no satellite coverage.
Location drift In areas with poor GNSS signals (e.g., tall buildings, basements), location drift may occur. Check if vibration is occurring near the accelerator, which might trigger false readings.
No command reply Verify the command format is correct. The vehicle might be in a network blind area. Ensure the SIM card is properly inserted and has SMS service.

10. Full SMS Commands List

Setting Commands

Functions Command Format Explanation
APN Setting APN,Network name[,name,password] APN,CMNET# (if no name & Password)
APN,internet,internet,internet# (if with name & Password)
Server Setting If set with Domain Name: SERVER,1,Domain,Port#
If set with IP: SERVER,0,IP,Port#		 SERVER,1,d.micodus.net,7700#
SERVER,0,47.254.77.28,7700#
Check IMEI IMEI# DEVICE IMEI No. : 0123456789
Change IMEI IMEICHG,354188046912460# NEW IMEI No. : 354188046912460
Restore factory settings FACTORY# RESTORE FACTORY SETTINGS OK
Restart device RESTART# RESTARTING...1 MINUTE WILL BE OK
Internet Traffic Switch TRAFFIC,ON# / TRAFFIC,OFF# OPEN TRAFFIC OK / CLOSE TRAFFIC OK
Time Zone Setting GMT,A,B,C# Example: GMT,E,8# (East +8 zone, no half time zone)
GMT,W,9,30# (West -9.5 zone, has half time zone)
A: E / W (East/West time zone)
B: 0 ~ 12 (whole time zone)
C: 0/15/30/45 (half time zone)
Set the angle upload ANGLEREP,X,A,B# Example: ANGLEREP,ON,30,3# (Sends data supplement when angle change exceeds 30 degrees for 3 seconds)
X=ON/OFF (default: ON)
A=5~180 degrees (diversion angle degree, default: 30 degrees)
B=2~5 seconds (detecting time, default: 3 seconds)
ANGLEREP,OFF# CANCEL UPLOAD ANGLE OK
Mileage Statistics MILEAGE,A,B# Example: MILEAGE,ON,5000# (Enable mileage statistics, initial value 5000km)
A=ON/OFF (default: Off)
B=0~999999 (Mileage initial value, unit: km; default: 0, mileage return to zero)
MIELEAGE# Query current mileage

Add/Delete SOS Administrator Number

Functions Command Format Explanation
Add SOS Administrator Number SOS,A,1st number,2nd number,3rd number# Set 3 numbers at a time: SOS,A,13800138000,13800138001,13800138002#
Set first number: SOS,A,13800138000#
Set second number: SOS,A,,13800138001#
Set third number: SOS,A,,,13800138002#
Delete SOS Administrator Number SOS,D,1st number,2nd number,3rd number# or SOS,D,1,2,3# Directly delete: SOS,D,13800138000#
Delete 1st number: SOS,D,1#
Delete 2nd number: SOS,D,2#
Delete 2nd and 3rd: SOS,D,2,3#

Add/Delete Center Number

Functions Command Format Explanation
Add Center Number CENTER,A,center number# Example: CENTER,A,008613800138000# (Tracker will only be controlled by this number. 0086 is country code).
Note: Set center number with country code prefix. Tracker will only reply to commands from this number.
Delete Center Number CENTER,D# DEL CENTER OK

Data Upload & Heartbeat

Functions Command Format Explanation
Data Upload Time Interval TIMER,T1,T2# Example: TIMER,5,180# (Upload every 5s when ACC is on, 180s when ACC is off).
T1: ACC ON upload interval (0/5~18000s, 0=no upload, default 10s).
T2: ACC OFF upload interval (0/5~18000s, default 10s).
Heartbeat Packet Upload HBT,time# Example: HBT,3# (Send heartbeat data every 3 min for connection maintenance).
Range: 1-60min, default 3min.

Sensor Sensitivity & Arm/Disarm

Functions Command Format Explanation
Sensor Sensitivity LEVEL,A# Example: LEVEL,2# (Set shake sensor level to 2).
A: Sensitivity Level 1-9 (1=weak, 9=strong vibration).
Arm manually ARM# Set the device into arm mode.
Disarm manually DISARM# Set the device out of arm mode.

Cut Off / Resume Fuel

Functions Command Format Explanation
Cut Off / Resume Fuel RELAY,A# A=1/2:
1: Enable relay immediately.
2: Enable relay safely (vehicle speed < 20km/h if GPS fixed, or stationary if GPS not fixed).
Example: RELAY,1# (Execute immediately).
Example: RELAY,2# (Execute safely).
RELAY,0# RESUME FUEL OK

Inquiry Commands

Functions Command Format Explanation
Version Inquiry VERSION# Device Reply Example: ID:9301074948, IMEI:354188046912460, ICCID:..., VERSION:MV930G_V2.0.2 BUILD:OCT 19 2016 16:31:00
Parameter Inquiry PARAM# Device Reply Example: ID:..., IMEI:..., APN:..., IP:..., TIMER:..., SPEEDLIMIT:..., ANGLERPT:..., CENTER:..., SOS:..., GMT:...
Latitude&Longitude Inquiry WHERE# LAT:N23.02930,LON:E114.32180,COURSE:0.00,SPEED:0.00KM/H,DATETIME:2015-05-23 14:39:11
Map URL Inquiry URL# http://map.google.com/?q=22.557868,113.935090 <0.0km/h 0.0> <2014-12-12 07:32:13> IMEI:...
Address Inquiry POSITION# Note: Reply message language is determined by device's language setting. If position content fails, device will reply Google Map location link.

Alarm Commands

Functions Command Format Explanation
Status Inquiry STATUS# Displays BATTERY, INTERNET, NET, GPS status, SPEED, ACC, RELAY, POWER, SENSOR, STATE (ARM/DISARM).
Alarms Parameters ALARM# Displays device ID, STATE, SPEED alarm status/value/way, SHIFT alarm status/value/way, VIBRATE alarm status/level/way, ACC alarm status/type/way, POWER DOWN alarm status/way, LOW VOLTAGE alarm status/way. Notes on Alarm Ways: 0: SERVER only, 1: SMS+GPRS, 2: GPRS+SMS+CALL.
Overspeed Alarm Setting SPEED,A,B,M# Example: SPEED,ON,100,1# (Alerts if speed exceeds 100km/h via SMS and server).
A=ON/OFF (default: OFF).
B=1~255 km/h (speed limit, default: 100 km/h).
M=0/1/2 (way of alarm: 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, default: 1).
SPEED,OFF# CANCEL OVERSPEED ALARM OK
Vibration Alarm Setting SENALM,A,M# Example: SENALM,ON,2# (Enable vibration alarm via SMS, server, and call).
A=ON/OFF (default: OFF).
M=0/1/2 (way of alarming: 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, default: 2).
SENALM,OFF# CANEL VIBRATE ALARM OK
Shift Alarm Setting SHIFT,A,B,M# Example: SHIFT,ON,300,1# (Set 300 meters shift alarm range; triggers when ignition is off and vehicle moves 300m, alerts via SMS and server).
A=ON/OFF (default: ON).
B=Shift Distance (Range: 100-9999m).
M=0/1/2 (way of alarm: 0: Server only, 1: SMS+Server, 2: Server+SMS+CALL, default: 1).
SHIFT,OFF# CANCEL SHIFT ALARM OK
Auto Arm By ACC ACCARM,ON,M# Example: ACCARM,ON,60# (Tracker enters arm status automatically after 60s when engine turns off).
Arm Time: M=5-1800s, default: 60s.
ACCARM,OFF# Close auto arm function.
ACC Status Change Alarm ACCALM,A,B,M# Example: ACCALM,ON,2,2# (Enable alarm for engine start/flameout via SMS, server, and call).
A=ON/OFF (Default: ON).
B=0/1/2 (0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC ON&OFF Alarm; Default: 2).
M=0/1/2 (way of alarm: 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, Default: 1).
ACCALM,OFF# Cancel ACC alarm function.
Power Disconnect Alarm PWRALM,A,M# Example: PWRALM,ON,1# (Alerts via SMS and server when external power disconnects).
A=ON/OFF (default ON).
M=0/1/2 (ways of alarming: 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, default: 2).
PWRALM,OFF# Close power disconnect alarm.
Low Voltage Alarm Setting LVALM,A,B,M# Example: LVALM,ON,11.2V,1# (Alerts via SMS and server when external power voltage is less than 11.5V).
A=ON/OFF (default: ON).
B=9-95 V (Low voltage threshold, e.g., 12.5V).
M=0/1/2 (way of alarming: 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call, default: 1).
LVALM,OFF# CANCEL LOW VOLTAGE ALARM OK.
Open Door Alarm Setting DOORALM,A,M# Example: DOORALM,ON,1# (Alerts via SMS and server when the door opens).
A=ON/OFF (default: ON).
M=0/1/2 (way of alarming: 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call, default: 1).
DOORALM,OFF#

11. Any Questions?

For inquiries, please contact:

  • E-mail: support@micodus.com
  • Skype: MiCODUS

12. Download the APP

Search for "MiCODUS" in the iOS App Store or Google Play Store to download the MiCODUS APP.

Alternatively, scan the QR codes below:

[QR code for Apple App Store]

[QR code for Google Play Store]

[QR code for HarmonyOS]

Models: MV710N Door Alarm Vehicle Locator, MV710N, Door Alarm Vehicle Locator, Alarm Vehicle Locator, Vehicle Locator

File Info : application/pdf, 13 Pages, 4.06MB

PDF preview unavailable. Download the PDF instead.

3e42d93fdd-mv710n-user-guide10

References

Adobe PDF library 15.00 Adobe Illustrator 25.0 (Windows)

Related Documents

Preview MiCODUS ML935 Tracker User Manual
Comprehensive user manual for the MiCODUS ML935 tracker, covering setup, specifications, features, troubleshooting, and SMS commands for device management.
Preview MiCODUS MV55G User Manual V1.0: Setup and Operation Guide
Comprehensive user manual for the MiCODUS MV55G tracker, covering features, specifications, activation, functions, installation, troubleshooting, and SMS commands.
Preview MiCODUS MV810G 4G GPS Tracker User Manual - Setup and Features
Comprehensive user manual for the MiCODUS MV810G 4G GPS tracker. Learn how to set up, configure, and use its features, including real-time tracking, geofencing, alarms, and SMS commands.
Preview MiCODUS MV790 GPS Tracker User Manual
Comprehensive guide to setting up and using the MiCODUS MV790 GPS tracker. Learn about features, specifications, installation, SMS commands, and troubleshooting for vehicle tracking and security.
Preview MiCODUS MV720 Tracker User Manual V2.0
User manual for the MiCODUS MV720 Tracker, providing setup instructions, specifications, troubleshooting, and SMS commands.
Preview MiCODUS MV66 User Manual V1.0: Setup and Operation Guide
Comprehensive user manual for the MiCODUS MV66 tracker, detailing setup, specifications, features, and SMS commands for effective vehicle tracking and monitoring.
Preview MiCODUS MV33 Tracker User Manual V2.0
Comprehensive user manual for the MiCODUS MV33 Tracker, covering features, specifications, activation, configuration, functions, installation, troubleshooting, and SMS commands.
Preview MiCODUS MP90G User Manual: Setup, Features, and SMS Commands
Comprehensive user manual for the MiCODUS MP90G GPS tracker. Learn how to set up, activate, and utilize its features like real-time tracking, SOS alerts, voice monitoring, and various alarm settings through detailed instructions and SMS commands.