Yamaha Speaker System
VXS10S/VXS10SW/VXS10ST/VXS10STW Owner's Manual
Precautions
WARNING
- Do not open: This device contains no user-serviceable parts. Discontinue use immediately and have it inspected by qualified Yamaha service personnel if it appears to be malfunctioning.
- Water warning: Do not expose the device to rain, use it near water or in damp/wet conditions, or place containers with liquids on it. If liquid seeps into the device, have it inspected by qualified Yamaha service personnel.
CAUTION
- Location: Do not place the device in an unstable position where it might accidentally fall. Avoid locations exposed to corrosive gases or salt air, as this may result in malfunction. Construction work for installation should be carried out by a professional constructor in accordance with relevant laws. Ensure mounting hardware and location can support the device's weight. Avoid locations with constant vibration. Use required tools for installation and inspect the device periodically. Transport or move the device with two or more people to prevent injury or damage.
- Connections: Turn off power for all devices before connecting to a power amplifier. Set all volume levels to minimum before turning power on or off. Use only speaker cables for connecting speakers to speaker connectors; other cable types may cause fire.
- Maintenance: Do not wipe the outer packaging with benzine, thinner, or synthetic detergent, nor use electrical contact cleaner, as these may damage the packaging and dissolve parts.
- Handling caution: Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into grille holes. If this occurs, have the device inspected by qualified Yamaha service personnel. Do not operate the device if the sound is distorting, as prolonged use in this condition could cause overheating and fire. When selecting a power amplifier, ensure its output power is lower than the device's power capacity (see SPECIFICATIONS). Even if the amplifier's output power is lower, excessive input signals causing clipping may damage the device. Malfunction or fire may occur with specific sounds/noises like feedback (with microphone), continuous extreme volume from musical instruments, extreme continuous distorted sound, or noise from plugging/unplugging cables while the amplifier is on.
Notice
Handling and Maintenance
- Do not place vinyl, plastic, or rubber objects on the device, as this might discolor the cabinet.
- When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
- Condensation may occur due to rapid temperature changes. If condensation is suspected, leave the device for several hours until it has completely dried out to prevent damage.
- Be sure to observe the amplifier's rated load impedance, particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier's rated range can damage the amplifier.
- When connecting speakers with high impedance, ensure the total output of each speaker does not exceed the rated output of the power amplifier.
About the Protection Circuit
- This speaker system has an internal protection circuit that shuts off the speaker unit when an excessive input signal is applied.
- If the speaker unit emits no sound, reduce the volume level of the amplifier immediately. The sound will return automatically in several seconds.
About This Manual
- The illustrations in this manual are for instructional purposes only and may appear somewhat different from your device.
- Yamaha cannot be held responsible for damage caused by improper use or modifications to the device.
Information for Users on Collection and Disposal of Old Equipment
- The symbol ♻ on products, packaging, and/or accompanying documents indicates that used electrical and electronic products should not be mixed with general household waste.
- For proper treatment, recovery, and recycling, take old products to applicable collection points in accordance with national legislation and Directive 2002/96/EC. This helps save valuable resources and prevent negative effects on human health and the environment.
- For more information, contact your local municipality, waste disposal service, or point of sale.
- For business users in the European Union: contact your dealer or supplier.
- For disposal in countries outside the European Union: contact local authorities or dealer for the correct method.
Unpacking
Contents:
- Speaker x 1
- Bracket base x 1
- Mounting bracket x 1
- Captive washer screw x 4
- Rubber spacer x 4 (14 mm thickness)
- Hexagon bolt x 4
- Spring washer x 4
- Flat washer x 4
- Safety wire x 1
- Owner's Manual (this manual)
Note: Screws/bolts to fasten the bracket onto the wall and speaker cables are not included.
Specifications
| Feature | VXS10S/VXS10SW | VXS10ST/VXS10STW |
|---|---|---|
| Type | Subwoofer, Bass reflex | Subwoofer, Bass reflex |
| Component | 10" (25 cm) Cone driver, Dual voice coil | 10" (25 cm) Cone driver, Dual voice coil |
| Nominal impedance | 8Ω + 8Ω | 8Ω + 8Ω |
| Power rating (NOISE) | 100 W + 100 W | 100 W + 100 W |
| Power rating (PGM) | 200 W + 200 W | 200 W + 200 W |
| Power rating (MAX) | 400 W + 400 W | 400 W + 400 W |
| Sensitivity (1W, 1m) *1 | 96 dB SPL | 96 dB SPL |
| Maximum SPL (Calculated, 1m) *2 | 125 dB SPL | 125 dB SPL |
| Frequency range (-10 dB) *1 | 45 Hz - 250 Hz | 45 Hz - 250 Hz |
| Subwoofer filter | Network: Low-pass filter 6 dB/Oct, 200 Hz Acoustic filter: Low-pass filter 6 dB/Oct, 200 Hz |
Network: Low-pass filter 6 dB/Oct, 200 Hz Acoustic filter: Low-pass filter 6 dB/Oct, 200 Hz |
| Satellite filter | Network: High-pass filter 6 dB/Oct, 200 Hz | Network: High-pass filter 6 dB/Oct, 200 Hz |
| Satellite impedance | 8Ω load per satellite output recommended *3 | 8Ω load per satellite output recommended *3 |
| Connector | Euroblock (4 pin) x 1: Input (CH1: +/-, CH2: +/-) Euroblock (4 pin) x 1: Satellite output (ST1: +/-, ST2: +/-) Euroblock (5 pin) x 1: transformer taps |
Euroblock (4 pin) x 1: Input (input: +/-, loop-thru: +/-) Euroblock (4 pin) x 1: Satellite output (ST1: +/-, ST2: +/-) Euroblock (5 pin) x 1: transformer taps |
| Transformer taps | 70 V: 200 W, 100 W, 50 W, 25 W 100 V: 200 W, 100 W, 50 W |
70 V: 200 W, 100 W, 50 W, 25 W 100 V: 200 W, 100 W, 50 W |
| Overload protection | Full-range power limiting to protect network and transducers | |
| Magnetically shielded | No | |
| Enclosure Shape | Rectangle | |
| Cabinet material | MDF | |
| Finish | Black (PVC, approximate value: Munsell N3) | White (PVC, approximate value: Munsell 3.5PB9.0/1) |
| Dimensions (Speaker only) | 260 x 500 x 389 mm (10.2" x 19.7" x 15.3") | |
| Net weight (Speaker only) | 16.5 kg (36.4 lb) | 19.5 kg (43.0 lb) |
*1: Half-space (2π)
*2: Calculated based on power rating and sensitivity, exclusive of power compression.
*3: Impedance lower limit (per satellite output) VXS10S/VXS10SW: 4 Ω, VXS10ST/VXS10STW: 8 Ω
Note: The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.
Installing the Speaker
When installing the speaker on the floor, attach the rubber spacers to the underside of the speaker to provide support. Affix the rubber spacers firmly.
When installing the speaker on a wall or ceiling, use the included brackets or optional U-bracket UB-DXR8. Ensure that the wall/ceiling is sufficiently strong. This package does not include the mounting hardware to install the included brackets/safety wire or the UB-DXR8. If you are not sure what materials are required for installation, consult a specialist.
Wall Installation (using included brackets)
Preparation (Cable)
Use stranded wire for cables attached to the Euroblock connector. Strip their insulation as shown in the figure, to about 7 mm (0.3 in.). Note: Do not plate stranded wires by solder, as doing so will cause the wire to break.
Step 1: Connect Wiring to Connector
Connect the cable from the amplifier to the "INPUT" socket, and the cable being connected to other speakers to the "SATELLITE SPEAKERS" socket. A signal input to CH1 of INPUT is output from ST1 of SATELLITE SPEAKERS, and signal input to CH2 of INPUT is output from ST2 of SATELLITE SPEAKERS.
For VXS10ST/VXS10STW, connect the included 5-pin Euroblock connector as shown below and set the appropriate wattage when using 100 V/70 V line. The diagram illustrates wattage settings for 70V and 100V lines (e.g., 70V/200W, 100V/200W, 70V/100W, 100V/100W, 70V/50W, 100V/50W, 70V/25W). Note: No setting should be made for the 100V line as shown in the far left illustration.
Remove the Euroblock connector from the speaker. After loosening the terminal screws of the Euroblock connector with a flat-blade screwdriver (blade less than 3 mm / 0.1 in.), insert the cable into each terminal and tighten the screws. Make sure that cables cannot be pulled out.
For VXS10ST/VXS10STW only: Plug the 5-pin Euroblock connector into the TRANSFORMER SETTINGS socket.
Step 2: Install the Speaker
Place the bracket base on the wall and mark the position for screws/bolts. The diameter of seven holes for screw/bolt (not included) is ø6.5 mm. Make holes in the wall for the bolts, as required, and feed the bolts through the holes. Affix the bracket base on the wall, ensuring the narrow edge is oriented downward.
Attach the mounting bracket to the speaker with the included screws with captive washer. The narrow edge of the mounting bracket should be oriented downward.
Attach the two rubber spacers to the bottom edge of the speaker. Make sure the spacers are located near the outer edge; otherwise, they will impede installation on the bracket base. Affix the rubber spacers firmly.
Slide the speaker down onto the bracket base until it locks in place. CAUTION: Be sure to perform this work with two or more people.
To detach the mounting bracket from the bracket base, release the lock of the mounting bracket with a long flat-blade driver and lift the speaker. CAUTION: Be sure to perform this work with two or more people.
Plug the Euroblock connectors into the SATELLITE SPEAKERS and INPUT sockets.
Ceiling Installation (using optional bracket UB-DXR8)
To determine the appropriate size of the UB-DXR8, download the "U BRACKET OWNER'S MANUAL" from the following manual library site: https://download.yamaha.com/
Assemble two L-shaped brackets into a U-shape using the M5 x 10 screws included with the UB-DXR8. Peel off the sheet from each rubber spacer (14 mm thickness; included with the speaker), and attach the spacers to the inside of each bracket arm, aligning the holes so that the hexagon bolts can be inserted. Affix the rubber spacers firmly.
Make sure that the width of the U bracket matches the speaker width.
Affix the U bracket on the ceiling using appropriate mounting hardware.
Use the hexagon bolts, spring washers, and flat washers included with the speaker to attach the speaker to the UB-DXR8. CAUTION: Be sure to perform this work with two or more people.
Plug the Euroblock connectors into the SATELLITE SPEAKERS and INPUT sockets.
Attach the Safety Wire
This section explains how to attach the included safety wire.
CAUTION:
- Make sure to take measures to prevent the speaker from falling down in the event of an installation failure.
- When installing the safety wire to the wall, install it higher than the wire's attachment point on the speaker, with as little slack as possible.
- If the safety wire is too short, prepare another wire appropriate for the speaker weight and installation conditions. If the wire is too long, should the speaker fall, the wire may snap as a result of too much strain.
1. Pass the safety wire through the eyebolt on the rear of the speaker.
2. Pass the bracket of the safety wire through the loop on the other end, and pull tight up against the eyebolt.
3. Affix the bracket of the safety wire to the wall.
Dimensions
Diagrams showing dimensions for the Bracket base and Mounting bracket for VXS10S/VXS10SW and VXS10ST/VXS10STW models. Units are in millimeters (mm).
Bracket base dimensions: 260 mm (width), 201 mm (height), 70 mm (depth), with mounting hole indicators.
Mounting bracket dimensions: 208 mm (width), 153 mm (height), with mounting hole indicators.
Resources and Contact Information
Manufacturer: Yamaha Corporation, 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan
Importer (for European Countries): Yamaha Music Europe GmbH, Siemensstrasse 22-34, 25462 Rellingen, Germany
Yamaha Pro Audio global website: http://www.yamahaproaudio.com/
Yamaha Downloads: https://download.yamaha.com/
Warranty Information: For detailed guarantee information and Pan-EEA/Switzerland warranty service, please visit http://europe.yamaha.com/warranty/. This section of the manual also provides warranty details in multiple languages including German, French, Dutch, Spanish, Italian, Portuguese, Greek, Swedish, Norwegian, Danish, Finnish, Polish, Czech, Hungarian, Estonian, Latvian, Lithuanian, Slovak, Slovenian, Bulgarian, and Romanian.
Manual Development Group ©2013 Yamaha Corporation. Published 04/2020 MWEI-E0
