Whirlpool® Top Load Washer Dimension Guide
This guide provides detailed planning dimensions and electrical requirements for Whirlpool Top Load Washers. Models covered include WTW5015LW, WTW5010LW, WTW5057LW, 7MWTW5017MW, and 7MWTW5057MW.
Electrical Requirements
| Model | Capacity (DOE/IEC) |
| WTW5015LW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| WTW5010LW | 4.6 cu ft DOE (US), 5.3 cu ft IEC (CAN) |
| WTW5057LW | 4.7 cu ft / 4.8 cu ft DOE (US), 5.4 cu ft / 5.5 cu ft IEC (CAN) |
| 7MWTW5017MW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| 7MWTW5057MW | 4.7 cu ft DOE (US), 5.4 cu ft IEC (CAN) |
Minimum Circuit Amperage Rating: 15 A
Operating Voltage: 120 V AC only
Operating Frequency: 60 Hz
Product Dimensions
Front View
Diagram showing a front view of the washer with dimensions labeled A (Height with feet) and B (Width).
| Dimension | in (minimum) | mm (minimum) | in (maximum) | mm (maximum) |
| A: Height (with feet) | 41½ | 1048 | 42¼ | 1074 |
| B: Width | 27¾ | 683 | - | - |
| C: Top of Lid Height (with feet) | 38½ | 962 | 38⅔ | 982 |
| D: Depth | 27 | 692 | - | - |
Side View
Diagram showing a side view of the washer with dimensions labeled E (Height with Lid Open), F (Height of Lid), G (Width of Lid), H (Water Inlet Valves Height), I (Water Inlet Valves from Side), J (Power Cord from Side), K (Power Cord Height), L (Power Cord Length), M (Drain Hose Outlet Height), and N (Drain Hose Outlet from Side).
| Dimension | in (minimum) | mm (minimum) | in (maximum) | mm (maximum) |
| E: Height with Lid Open | 55¾ | 1415 | 56⅜ | 1432 |
| F: Height of Lid | 18⅞ | 449 | - | - |
| G: Width of Lid | 23¼ | 593 | - | - |
| H: Water Inlet Valves Height | 37⅞ | 962 | 39½ | 1003 |
| I: Water Inlet Valves from Side | 4½ | 116 | - | - |
| J: Power Cord from Side | 2½ | 63 | - | - |
| K: Power Cord Height | 37⅜ | 950 | 37½ | 953 |
| L: Power Cord Length | 62 | 1530 | - | - |
| M: Drain Hose Outlet Height | 7¼ | 170 | 7¾ | 197 |
| N: Drain Hose Outlet from Side | 4⁵⁄₁₆ | 107 | - | - |
| O: Drain Hose Length | 41 | 1040 | - | - |
| P: Diameter of Drain Hose | 1 | 25 | - | - |
Installation Spacing
Recessed Area or Closet Installation
Diagram illustrating recommended spacing for installing the washer in a recessed area or closet. It shows clearances for the sides, top, and front, as well as ventilation openings required for the closet door.
The dimensions shown are recommended clearances, except for the closet door ventilation openings, which are minimum requirements. This washer has been tested for installation with 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, as well as for companion appliances and clearances for walls, doors, and floor moldings. Add 1" (25 mm) spacing on all sides of the washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in the door are required.
